Miller Electric SS-75D12 manual Adjusting Control Tilt Bracket, Installing Boom And Reel Support

Page 14

4-2. Adjusting Control Tilt Bracket

1 Tilt Bracket

2 Rear Pivot Screw

3 Front Screw

Loosen rear pivot screw. Remove front screw. Pivot control down- ward to desired viewing angle. Re- place and tighten front screw. Tight- en pivot screw.

803 155

4-3. Installing Boom And Reel Support

1Swivel Plates

2Yoke

Remove hardware from swivel plates and yoke.

3 Boom

Set boom into swivel as shown.

4 Yoke Pin

Install pin through yoke. Install cot- ter pin and spread ends.

5 Bolt

Install bolt, tighten hardware, and back bolt off one half turn.

6 Locking Knob

Install locking knob but do not tighten.

7Reel Support Install reel support.

Tools Needed: 3/8, 3/4 in

ST-142 596-C

OM-230 298 Page 10

Image 14

Contents Description OM-230 298AProcesses File MIG GmawFrom Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer unIncendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures graves’EMPLOI Excessif peut SUR Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaquesInstalling Swivel Into Pipe Post − InstallationSpecifications − IntroductionAdjusting Control Tilt Bracket Installing Boom And Reel SupportInstalling Wire Guide Extension Equipment Connection DiagramPin Information Control Box ConnectionsPin Plug Information Motor Speed Wire Type Wire Size Feed Speed Capability Removing Safety Collar And Adjusting BoomWire Type, Size, And Feed Speed Capability Table Gun Recommendation TableRemoval Installing Drive RollsInstallation Installing PD Continuous Wire Guides Installing PD continuous wire guides with PD drive rollsInstalling Non-PD Old Style Wire Guides Installing wire guides with non- PD old- style drive rollsInstalling gun without Accu-Mate connection Installing Welding GunInstalling gun with Accu-Mate connection Installing gun with Accu-Mate connec- tionInstalling Welding Wire And Adjusting Pressure Drive Setting Manually Adjusted Run-In S1-1 And S1-2 Setting Internal DIP SwitchesRun-In Disabled S1-1 S1-1 And S1-2General Terms Cold Wire Jog Equipment DIP Switch Settings For Models With Meters OnlyDigital Meter DIP Switch Setting − OperationPower Switch Jog/Purge And Trigger HoldYou can adjust the preset volt Brush Inspection And Replacement − Maintenance and TroubleshootingRoutine Maintenance Disconnect power before maintainingError Indications DiagnosticsIndicated Error Trouble Remedy TroubleshootingDisconnect power before troubleshooting − Electrical Diagram Circuit DiagramStart Your Professional Welding Career Now − Parts List Main AssemblyQuantity Control Box 070 Boom Assembly Boom Assembly -1Item Drive Assembly, Wire Drive Assembly With Motor Support, Hub & Reel PD-V OM-230 298 Service SupportOwner’s Record Miller Electric Mfg. Co