Miller Electric Metro 250D Installation, AC Auxiliary Power Curve, Installing Welding Generator

Page 21

3.6AC Auxiliary Power Curve

The auxiliary power curve shows the auxiliary power in amperes available at the receptacles.

SA-180 260

4.Installation

4.1Installing Welding Generator

install1 1/97 − Ref. ST-800 652 / Ref. ST-800 477-A / ST-158 936-A / S-0854

1Generator Base

2Metal Vehicle Frame

3Equipment Grounding Terminal

4Grounding Cable

Use #10 AWG or larger insulated copper wire.

YIf unit does not have GFCI re- ceptacles, use GFCI- protected extension cord.

Movement		Airflow Clearance
Y Do not lift unit from end.		18 in
		(460 mm)	18 in
			18 in
		18 in	(460 mm)
	OR	(460 mm)
	OR
		18 in	18 in
		18 in	(460 mm)
		(460 mm)	(460 mm)
		(460 mm)
Location	Grounding
		1	3
		1	4
		GND/PE	4
		GND/PE
	OR	OR
	OR
		Electrically bond genera-
		tor frame to vehicle frame
	2	by metal-to-metal contact.	2

OM-402

Image 21

Contents OM-402B ProcessesDescription From Miller to You Metro 250D Table of ContentsPage Safety Precautions − Read Before Using Symbol UsageArc Welding Hazards Engine Hazards Moving Parts can cause injury Battery Explosion can BlindEngine Exhaust Gases can kill Engine Heat can cause fireEMF Information Principal Safety StandardsRadiation can cause interference ARC Welding can cause interferenceConsignes de sécurité − lire avant utilisation Signification des symbolesUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereuxDES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer un in- cendie ou une explosionDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut affecter l’ouïe’EXPLOSION DE LA Batterie peut DES Organes Mobiles peuvent provoquer des blessuresLA Chaleur DU Moteur peut pro- voquer un incendie LA Chute DE L’APPAREIL peut blesserInformation sur les champs électromagnétiques Principales normes de sécuritéÉlectrostatiques peuvent endommager les circuits imprimés UNE Remorque QUI Bascule peut entraîner des blessuresDefinitions Symbols and DefinitionsGeneral Precautionary Label Fan and Moving Parts Label Battery Charging LabelDiesel Fuel Label Hot Muffler LabelFalling Equipment Label Activation Tag− 50 h Std Manufacturer’s Rating Label Do Not Use Ether LabelWeld, Power, and Engine Specifications SpecificationsDimensions, Weights, and Operating Angles Volt-Ampere CurveDuty Cycle and Overheating Fuel ConsumptionAC Auxiliary Power Curve InstallationInstalling Welding Generator Location GroundingEngine Prestart Checks Connecting Battery and Installing Exhaust PipeStop engine Connect negative − cable lastSelecting Weld Cable Sizes Connecting to Weld Output Terminals100 ft 30 m or Less 10 − 60% 60 − 100% Duty 10 − 100% Duty CycleRemote 14 Receptacle RC1 Information Ref. ST-158Socket Information Operating the Welding Generator Using Idle Lock SwitchFront Panel Controls PlugRemote Amperage and Contactor Control Operating Auxiliary Equipment Auxiliary Power ReceptaclesMaintenance & Troubleshooting 100 Hrs Maintenance Changing Engine Oil and Oil Filter To Clean air filter Servicing Air CleanerDo not clean housing with air hose Changing Fuel FiltersAdjusting Engine Speed Idle Speed AdjustmentWeld/Power Speed Adjustment Remote Control Circuit Weld And Auxiliary Power CircuitsOverload Protection Engine Control CircuitStop engine and let cool. Reinstall cleanout plug Welding TroubleshootingServicing Optional Spark Arrestor Trouble RemedyEngine Troubleshooting Auxiliary Power TroubleshootingUle OM-402 Circuit Diagram for Welding Generator Electrical DiagramSC-181 Run-In Procedure WetstackingHeavy loading during first Load Bank Run-In Procedure Using Load BankRun-In Procedure Using Resistance Grid Auxiliary Power Guidelines Selecting EquipmentGrounding Generator to Truck or Trailer Frame Grounding When Supplying Building Systems How Much Power Does Equipment Require?Amperes x Volts = Watts Approximate Power Requirements for Farm/Home Equipment Approximate Power Requirements for Industrial MotorsIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements for Contractor EquipmentHow Much Power Can Generator Supply? Power Required to Start MotorSingle-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 = Starting Amperage VoltsTypical Connections to Supply Standby Power Current Load Watts Amperes Selecting Extension Cord Use Shortest Cord PossibleMain Assembly Parts ListST-801 488-A PC6 11.1CB9 Panel, Front w/Components .1 Item CB5 11.2Generator .1 Item Diode Board Control Box w/Components .1 ItemOM-402 Page OM-402 Page Metro 250D Options and AccessoriesCall Miller for your local Miller distributor Miller Electric Mfg. Co Owner’s Record