Miller Electric Metro 250D manual Maintenance & Troubleshooting

Page 28

7.Maintenance & Troubleshooting

7.1Routine Maintenance

Recycle engine

fluids.

YStop engine before maintaining.

.See also Engine Manual and Maintenance

Label. Service engine more often if used in severe conditions.

8 h

Check fluid levels. See Section 4.3.

50 h

Clean air filter element. See Section 7.5.

Wipe up spills.

Clean and tighten weld connections.

100 h

Change oil. See Section 7.3 and maintenance label.

200 h

Change oil filter. See Section 7.3 and maintenance label.

Change fuel filter. See Section 7.4.

Clean and

Clean cooling

tighten battery

system.

connections.

See engine manual.

See Section 4.2.

 

Change fuel filter. See Section 7.4.

Replace unreadable labels.

250 h

Check and clean spark arrestor.

See Section 7.8.

300 h

Check valve clearance.

See engine manual.

500 h

Repair or replace cracked cables.

Test/time injectors. See engine manual.

1000 h

Blow out or vacuum inside.

During heavy service,OR clean monthly.

24

OM-402

Image 28
Contents Processes OM-402BDescription From Miller to You Table of Contents Metro 250DPage Symbol Usage Safety Precautions − Read Before UsingArc Welding Hazards Engine Hazards Battery Explosion can Blind Moving Parts can cause injuryEngine Exhaust Gases can kill Engine Heat can cause firePrincipal Safety Standards EMF InformationRadiation can cause interference ARC Welding can cause interferenceSignification des symboles Consignes de sécurité − lire avant utilisationUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in- cendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut affecter l’ouïeDES Organes Mobiles peuvent provoquer des blessures ’EXPLOSION DE LA Batterie peutLA Chaleur DU Moteur peut pro- voquer un incendie LA Chute DE L’APPAREIL peut blesserPrincipales normes de sécurité Information sur les champs électromagnétiquesÉlectrostatiques peuvent endommager les circuits imprimés UNE Remorque QUI Bascule peut entraîner des blessuresSymbols and Definitions DefinitionsGeneral Precautionary Label Battery Charging Label Fan and Moving Parts LabelHot Muffler Label Diesel Fuel LabelActivation Tag Falling Equipment Label− 50 h Std Do Not Use Ether Label Manufacturer’s Rating LabelSpecifications Weld, Power, and Engine SpecificationsDimensions, Weights, and Operating Angles Volt-Ampere CurveFuel Consumption Duty Cycle and OverheatingInstallation AC Auxiliary Power CurveInstalling Welding Generator Location GroundingConnecting Battery and Installing Exhaust Pipe Engine Prestart ChecksStop engine Connect negative − cable lastConnecting to Weld Output Terminals Selecting Weld Cable Sizes100 ft 30 m or Less 10 − 60% 60 − 100% Duty 10 − 100% Duty CycleRef. ST-158 Remote 14 Receptacle RC1 InformationSocket Information Using Idle Lock Switch Operating the Welding GeneratorFront Panel Controls PlugRemote Amperage and Contactor Control Auxiliary Power Receptacles Operating Auxiliary EquipmentMaintenance & Troubleshooting 100 Hrs Maintenance Changing Engine Oil and Oil Filter Servicing Air Cleaner To Clean air filterDo not clean housing with air hose Changing Fuel FiltersIdle Speed Adjustment Adjusting Engine SpeedWeld/Power Speed Adjustment Weld And Auxiliary Power Circuits Remote Control CircuitOverload Protection Engine Control CircuitWelding Troubleshooting Stop engine and let cool. Reinstall cleanout plugServicing Optional Spark Arrestor Trouble RemedyAuxiliary Power Troubleshooting Engine TroubleshootingUle OM-402 Electrical Diagram Circuit Diagram for Welding GeneratorSC-181 Wetstacking Run-In ProcedureHeavy loading during first Run-In Procedure Using Load Bank Load BankRun-In Procedure Using Resistance Grid Selecting Equipment Auxiliary Power GuidelinesGrounding Generator to Truck or Trailer Frame How Much Power Does Equipment Require? Grounding When Supplying Building SystemsAmperes x Volts = Watts Approximate Power Requirements for Industrial Motors Approximate Power Requirements for Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsApproximate Power Requirements for Contractor Equipment Contractor Rating Starting Watts Running WattsPower Required to Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 = Starting Amperage VoltsTypical Connections to Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible Current Load Watts AmperesParts List Main AssemblyST-801 488-A 11.1 PC6CB9 Panel, Front w/Components .1 Item 11.2 CB5Generator .1 Item Control Box w/Components .1 Item Diode BoardOM-402 Page OM-402 Page Options and Accessories Metro 250DCall Miller for your local Miller distributor Owner’s Record Miller Electric Mfg. Co