Miller Electric PipePro 304 manual Engine Hazards, Compressed Air Hazards

Page 7

1-3. Engine Hazards

BATTERY EXPLOSION can BLIND.

DAlways wear a face shield, rubber gloves, and

protective clothing when working on a battery.

D Stop engine before disconnecting or connect- ing battery cables or servicing battery.

DDo not allow tools to cause sparks when working on a battery.

DDo not use welder to charge batteries or jump start vehicles.

DObserve correct polarity (+ and −) on batteries.

DDisconnect negative (−) cable first and connect it last.

FUEL can cause fire or explosion.

D Stop engine and let it cool off before checking or adding fuel.

DDo not add fuel while smoking or if unit is near any sparks or open flames.

DDo not overfill tank — allow room for fuel to expand.

DDo not spill fuel. If fuel is spilled, clean up before starting engine.

DDispose of rags in a fireproof container.

DAlways keep nozzle in contact with tank when fueling.

MOVING PARTS can cause injury.

D Keep away from fans, belts, and rotors.

D Keep all doors, panels, covers, and guards closed and securely in place.

DStop engine before installing or connecting unit.

DHave only qualified people remove doors, panels, covers, or guards for maintenance and troubleshooting as necessary.

DTo prevent accidental starting during servicing, disconnect negative (−) battery cable from battery.

DKeep hands, hair, loose clothing, and tools away from moving parts.

DReinstall doors, panels, covers, or guards when servicing is finished and before starting engine.

DBefore working on generator, remove spark plugs or injectors to keep engine from kicking back or starting.

DBlock flywheel so that it will not turn while working on generator components.

HOT PARTS can cause severe burns.

DDo not touch hot parts bare handed.

D Allow cooling period before working on equip- ment.

DTo handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and clothing to prevent burns.

STEAM AND HOT COOLANT can burn.

DIf possible, check coolant level when engine is cold to avoid scalding.

D Always check coolant level at overflow tank, if present on unit, instead of radiator (unless told otherwise in maintenance section or engine manual).

DIf the engine is warm, checking is needed, and there is no over- flow tank, follow the next two statements.

DWear safety glasses and gloves and put a rag over radiator cap.

DTurn cap slightly and let pressure escape slowly before completely removing cap.

Using a generator indoors CAN KILL YOU IN MINUTES.

D Generator exhaust contains carbon monoxide.

This is a poison you cannot see or smell.

DNEVER use inside a home or garage, EVEN IF doors and windows are open.

DOnly use OUTSIDE and far away from windows, doors, and vents.

BATTERY ACID can BURN SKIN and EYES.

DDo not tip battery.

DReplace damaged battery.

DFlush eyes and skin immediately with water.

ENGINE HEAT can cause fire.

D Do not locate unit on, over, or near combustible surfaces or flammables.

DKeep exhaust and exhaust pipes way from flammables.

EXHAUST SPARKS can cause fire.

D Do not let engine exhaust sparks cause fire.

DUse approved engine exhaust spark arrestor in required areas — see applicable codes.

1-4. Compressed Air Hazards

BREATHING COMPRESSED AIR can cause serious injury or death.

DDo not use compressed air for breathing.

DUse only for cutting, gouging, and tools.

COMPRESSED AIR can cause injury.

DWear approved safety goggles.

DDo not direct air stream toward self or others.

TRAPPED AIR PRESSURE AND WHIPPING HOSES can cause injury.

DRelease air pressure from tools and system be- fore servicing, adding or changing attach- ments, or opening compressor oil drain or oil fill cap.

OM-492 Page 3

Image 7
Contents Visit our website at OM-492190 603BF 2007−05 ProcessesDescription File Engine-DrivenFrom Miller to You Table of Contents Options and Accessories Warranty HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion Fumes and Gases can be hazardousBuildup of GAS can injure or kill ARC Rays can burn eyes and skinCompressed Air Hazards Engine HazardsFalling Unit can cause injury Welding Wire can cause injuryHOT Parts can cause burns and injury Fire or Explosion hazardRadiation can cause interference Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationIndique des instructions spécifiques Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation UN Choc Électrique peut tuerLE Bruit peut affecter l’ouïe DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LE Soudage peut provoquer un in cendie ou une explosionDES Organes Mobiles peuvent pro voquer des blessures ’EXPLOSION DE LA Batterie peu’AIR Comprimé peut provoquer des blessures LA Chaleur DU Moteur peut pro- voquer un incendieRisque D’INCENDIE OU D’EXPLO- Sion ’EMPLOI Excessif peut LE Surchauffement peut endom- mager le moteur électriqueDES Organes Mobiles peuvent provoquer des blessures LES Fils DE Soudage peuvent provoquer des blessuresEn ce qui concerne les implants médicaux Proposition californienne 65 AvertissementsPrincipales normes de sécurité Information EMF− Definitions − SpecificationsSymbol Definitions Weld, Power, And Engine SpecificationsDuty Cycle And Overheating Dimensions, Weights, and Operating AnglesCV Mode CC ModeVolt-Ampere Curves Fuel Consumption Installing Welding Generator − InstallationOil Engine Prestart ChecksThis unit has a low oil pressure shut FuelCable last Connecting The BatteryConnect Negative −Tools Needed 1/2 Installing Exhaust PipeStick And TIG Welding Connecting To Weld Output TerminalsCorrect Installation Stop engineRemote 14 Receptacle RC14 Information Selecting Weld Cable SizesMount on lower Front panel Stop engine, and let coolUse thick-walled rubber hose. Do not use EngineOperating Engine Block Heater Controls See Section − Operating Welding GeneratorDescription Of Controls See Section Meter Functions Mode Switch SettingsMode Meter Reading At Idle Meter Reading While Welding Mode Switch Setting Process Output On/Off ControlStarting Do not use ether Lift-Arc TIG ProcedureBattery Recommendations For Extreme Cold Weather OperationWeld Total 120 Generator Power Receptacles And Circuit BreakersGenerator power decreases as weld current increases − Operating Auxiliary EquipmentTected extension cord Optional Gfci Receptacles And Circuit BreakersIf unit does not have Gfci Receptacles, use GFCI-proReceptacle Current Available in Amperes 240Maintenance Label − Maintenance and TroubleshootingRoutine Maintenance Stop engine and let cool Servicing Spark ArrestorTo clean air filter Servicing Air CleanerServicing Engine Lubrication And Fuel Systems Servicing Engine Cooling System Be sure solenoid plunger rod Adjust throttle link Throttle armReplacing Throttle Solenoid TS1 − cable firstUsing Engine Stop Lever Adjusting Engine SpeedAdjusting Idle Speed Adjusting Weld/Power SpeedOverload Protection Voltmeter/Ammeter Help Displays Welding TroubleshootingTrouble Remedy No power output Reset supplementary protectors see Section Generator PowerNecessary parts Engine CT1 Work like a Pro Circuit Diagram For Welding Generator − Electrical Diagrams212 633-F Do not perform run-in − RUN-IN ProcedureProcedure at less than WetstackingRun-In Procedure Using Load Bank From flammables Run-In Procedure Using Resistance GridSelecting Equipment − Generator Power GuidelinesGrounding Generator To Truck Or Trailer Frame Amperes x Volts = Watts Grounding When Supplying Building SystemsHow Much Power Does Equipment Require? Use ground device as stated in electrical codesFarm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Industrial Motors Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentKVA/HP x HP x 1000 / Volts = Starting Amperage Power Required To Start MotorHow Much Power Can Generator Supply? Single-Phase Induction Motor Starting RequirementsTypical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible 105 104 102 − Parts List30 Fig Item Dia Part Description Quantity Mkgs Dia Part Description Quantity Mkgs 213 Front Panel 24 PL1, PL2, PL3 Inverter Assembly -1, Item Inverter Assembly24 . . HD1 189 Generator Work like a Pro TM-188 304 Invision 354MP Start Your Professional Welding Career Now Your distributor also gives ServiceSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact