Bosch Power Tools 1619EVS manual Preparation For Use With Bosch Router Table

Page 18

BM 2610933969 09-12_BM 2610933969 09-12.qxp 9/20/12 9:19 AM Page 18

Preparation For Use With Bosch Router Table

Your router is uniquely suited for use in the Bosch router table. For detailed instructions about router table procedures, please refer to the manual that is supplied with the router table. To prepare the 1619EVS for table mounting, do the following:

HOUSING

FIG. 22

PLUNGE LOCK

OVERRIDE LEVER

d. Plunge the router motor down as far as it will go.

e. While holding the motor down, press and hold down spring defeat button.

f.Allow the motor to move up slightly.

g.Release the button.

The plunge return spring pressure is now disengaged.

PLUNGE

LOCK LEVER

DEPTH ROD

FIG. 24

SPRING DEFEAT

BUTTON

1.Engage plunge lock override lever as follows: Facing the rear of the router, move plunge lock lever approximately 90 degrees clockwise. Depress small override lever and slowly release plunge lock lever until override lever catches firmly on metal housing as shown in diagram. The motor is now free to move up and down on the posts (Fig. 22).

COARSE

ADjUSTMENT

LOCK

FIG. 23

SPRING

DEFEAT BUTTON

2.Engage the plunge return spring defeat (Fig. 23).

Note: This unique feature makes it easier to adjust the height of the bit when the router is mounted under a router table.

a. Move the depth rod to its highest position, and lock in place with coarse adjustment lock.

b. Remove the collet chuck.

c. Rotate depth stop turret to the position shown in Fig. 23.

KEYHOLE

DEPTH STOP

TURRET

3.Connect the depth rod to the depth stop turret by rotating the depth stop turret so that the large end of keyhole slot is aligned with the lower end of the depth rod. Release coarse adjust lock, and lower depth rod into the large end of keyhole slot. Rotate depth stop turret until the smaller end of the keyhole traps the end of depth rod (Fig. 24). (To keep the rod in the keyhole, there is a raised rim around the underside of the smaller end of the keyhole. When inverted, the weight of the router keeps the depth rod inside the raised rim.) Note:

When the router motor is at its further point away from the base, the motor must be moved slightly closer to the base so the depth rod can clear the raised rim.

-18-

Image 18
Contents BM 2610933969 09-12BM 2610933969 09-12.qxp 9/20/12 919 AM Ver la páginaElectrical safety General Power Tool Safety WarningsWork area safety Personal safetyMany accidents are caused by poorly maintained power tools Safety Rules for RoutersService Protruding cutting bit may cause tool to jumpSafety Rules for Router Table Accidental start-up of the tool can cause injuryAdditional Safety Warnings Symbols Name Designation/ExplanationSymbols Functional Description and Specifications RouterSelecting Bits AssemblyInstalling a Router BIT Removing the Router BITRouter Dust Collection Installing Templet Guide AdapterOperating Instructions Plunging ActionFine ADjUSTMENT Knob Coarse Depth ADjUSTMENTCoarse ADjUSTMENT Indicator Fine ADjUSTMENT IndicatorMaking Progessively Deeper Plunge Cuts Dial Setting RPM Application Trigger Switch and LOCK-ON ButtonSoft Start Feature Electronic Variable Speed ControlEdge Forming Feeding the RouterRate of Feed EndgrainDust Collection While Edge Forming Do not use this dustCentering the SUB-BASE Templet Guides DELUxE Router Guide Not included, available as accessory Templet pattern by that amount, due to the bit position FigPreparation For Use With Bosch Router Table Engage the plunge return spring defeat FigAttaching Router to Mounting Plate Connect the Router and the Router Table SwitchOperation in Router Table Feeding the Workpiece on Router TableTool Lubrication MaintenancePreventive maintenance Carbon BrushesAccessories Sécurité du lieu de travail Sécurité électriqueRègles de sécurité concernant les toupies Utilisation et entretien des outils ÉlectroportatifsEntretien Consignes de sécurité pour table de toupillage Avertissements supplémentaires concernant la sécurité Le plomb provenant des peintures à base de plombTours, coups, vitesse en surface, orbites SymbolesSymbole Nom Désignation/Explication La vitesse augmente depuis le réglageSymboles suite Description fonctionnelle et spécifications DéfonceuseMontage DES Fers AssemblageChoix DES Fers Pour Enlever UN FER DE DéfonceuseRamassage DES Poussières Installation DE L’ADAPTATEUR DE Guide DE GabaritConsignes d’utilisation Mouvement DE PlongéeBouton DE Réglage FIN Réglage Grossier DE LA ProfondeurIndex DE Réglage Grossier Index DE Réglage FINAugmentation Progressive DE LA Profondeur DE Coupe Système DE Démarrage Progressif Commande Électronique DE Variation DE VitesseGchette ET Bouton DE Verrouillage SUR Marche TR/MIN ApplicationMoulurage DE Chants Avance DE LA DéfonceuseVitesse D’AVANCE Chant de bout endommage la pièceFixation DU Capuchon D’EXTRACTION DE Poussière ’emploi de l’outil avec ces accessoiresRamassage DE Poussière Lors DU Moulurage DE Chants Chant DE LA PièceCentrage DE LA SOUS-EMBASE ET DES Guides DE Gabarit Profil DU Gabarit Déport Pièce DE DéfonceuseTige DE Profondeur Bouton DE Désarmement DU Ressort Préparation pour utilisation avec la table de toupillageProfondeur Levier DE Tourelle DE Butée DE ProfondeurRéglage DE LA Profondeur Utilisation avec la table de toupillageDE Montage Avance DE LA Pièce SUR UNE Table DE ToupillageLubrification DE L’OUTIL EntretienNettoyage Balais OU CharbonsAccessoires Capuchon d’extraction de poussière pour moulurage de chantsIndex à graduation métrique pour réglage grossier Seguridad del área de trabajo Seguridad eléctricaSeguridad personal Normas de seguridad para fresadoras MecánicasServicio de ajustes y reparaciones Instrucciones de seguridad para la mesa de fresadora Advertencias de seguridad adicionales Símbolos Símbolo Nombre Designación/explicaciónUn número más alto significa mayor velocidad Símbolos continuación Descripción funcional y especificaciones FresadorasRemoción DE LA Broca DE Fresadora EnsamblajeSelección DE Brocas Cuidado DEL Mandril PortaherramientaInstalación DEL Adaptador DE Guías DE Plantilla FresadoraCubierta a mangueras de aspiración de 1-1/4 y 1-1/2 Acción DE PenetraciónPomo DE Ajuste Fino Ajuste DE Profundidad GruesoIndicador DE Ajuste Grueso Indicador DE Ajuste FinoProgresivamente MÁS Profundos Posición DEL Dial Interruptor Gatillo Y Botón DE Fijación EN EncendidoDispositivo DE Arranque Suave AplicaciónConformado DE Bordes Avance DE LA FresadoraVelocidad DE Avance CorteColocación DE LA Cubierta DE Extracción DE Polvo Lea y entienda estasPara evitar Enredar Cubierta DE Extracción DE PolvoCentrado DE LA Subbase Y LAS Guías DE Plantilla Guiado DE LA FresadoraGuía DE Fresadora DE Lujo Palanca DE Fijación DE LA Profundidad Preparación para la utilización con la mesa de fresadoraCarcasa Palanca DE Cierre DE Ajuste Grueso Botón DE Anulación DEL ResorteAjuste DE LA Profundidad Utilización en la mesa de fresadoraSujeción DE LA Fresadora a LA Placa DE Montaje Avance DE LA Pieza DE Trabajo Sobre UNA Mesa DE FresadoraMantenimiento ServicioLimpieza Accesorios Cubierta de extracción de polvo con anillo de mejoraBM 2610933969 09-12BM 2610933969 09-12.qxp 9/20/12 919 AM Remarques Notas 2610933969
Related manuals
Manual 56 pages 39.23 Kb