Bosch Power Tools 1619EVS Assembly, Selecting Bits, Installing a Router BIT, Collet Chuck Care

Page 9
! WARNING

BM 2610933969 09-12_BM 2610933969 09-12.qxp 9/20/12 9:19 AM Page 9

Assembly

SELECTING BITS

A wide assortment of router bits with different profiles are available as accessories. Use 1/2" shank whenever possible, and only use good quality bits.

To prevent personal injury, ! WARNING always remove the plug from

power source before removing or installing bits or accessories.

INSTALLING A ROUTER BIT

1.Lay router on its side with the flat side of base resting on the bench.

2.Press spindle lock to prevent rotation of collet chuck. NOTE: it may be necessary to rotate collet nut to engage spindle lock (Fig. 3).

3.Next, use the collet wrench to loosen the collet chuck assembly in counter-clockwise direction (viewed from bottom of router).

4.Insert the shank of the router bit into the collet chuck assembly as far as it will go, then back the shank out until the cutters are approximately 1/8" to 1/4" away from the collet nut face.

5.With the router bit inserted and the spindle lock engaged, use the collet wrench to firmly tighten the collet chuck assembly in a clockwise direction (viewed from bottom of router).

To ensure proper gripping of the router bit and minimize run-out, the shank of the router bit must be inserted at least 5/8".

Cutter diameter must be at least 1/4" smaller than the

opening for the bit and cutter.

For use with larger bits, see “Preparation for use with Bosch Router Table” on page 17.

! CAUTION

To prevent damage to tool,

 

do not tighten collet without

a bit.

 

NOTE: The bit shank and chuck should be clean and free of dust, wood, residue and grease before assembling.

REMOVING THE ROUTER BIT

1.Press spindle lock to prevent rotation of collet chuck, and turn the collet chuck assembly in a counter-clockwise direction.

2.Once the collet chuck assembly is loosened, continue to turn the collet chuck assembly until it pulls the collet free from its taper, and the router bit can be removed.

NOTE: The collet chuck is self-extracting; it is NOT necessary to strike the collet chuck to free the router bit.

COLLET CHUCK CARE

With the router bit removed, continue to turn the

collet chuck counter-

 

FIG. 4

clockwise until it is

 

 

 

free of the shaft. To

 

 

assure a firm grip,

COLLET

 

occasionally blow

COLLET

out the collet chuck

COLLET

CHUCK

with compressed air,

 

and clean the taper

NUT

 

in the armature assembly shaft with a tissue or fine brush. The collet chuck is made up of two component parts that snap together (Fig. 4); check to see that the collet is properly seated in the collet chuck nut and lightly thread the collet chuck back onto the armature shaft. Replace worn or damaged collet chucks immediately.

FIG. 3

WRENCH

SHANK

BIT

COLLET CHUCK

BASE

SPINDLE LOCK

-9-

Image 9
Contents Ver la página BM 2610933969 09-12BM 2610933969 09-12.qxp 9/20/12 919 AMWork area safety General Power Tool Safety WarningsElectrical safety Personal safetyService Safety Rules for RoutersMany accidents are caused by poorly maintained power tools Protruding cutting bit may cause tool to jumpAccidental start-up of the tool can cause injury Safety Rules for Router TableAdditional Safety Warnings Name Designation/Explanation SymbolsSymbols Router Functional Description and SpecificationsInstalling a Router BIT AssemblySelecting Bits Removing the Router BITOperating Instructions Installing Templet Guide AdapterRouter Dust Collection Plunging ActionCoarse ADjUSTMENT Indicator Coarse Depth ADjUSTMENTFine ADjUSTMENT Knob Fine ADjUSTMENT IndicatorMaking Progessively Deeper Plunge Cuts Soft Start Feature Trigger Switch and LOCK-ON ButtonDial Setting RPM Application Electronic Variable Speed ControlRate of Feed Feeding the RouterEdge Forming EndgrainDo not use this dust Dust Collection While Edge FormingCentering the SUB-BASE Templet Guides Templet pattern by that amount, due to the bit position Fig DELUxE Router Guide Not included, available as accessoryEngage the plunge return spring defeat Fig Preparation For Use With Bosch Router TableOperation in Router Table Connect the Router and the Router Table SwitchAttaching Router to Mounting Plate Feeding the Workpiece on Router TablePreventive maintenance MaintenanceTool Lubrication Carbon BrushesAccessories Sécurité électrique Sécurité du lieu de travailRègles de sécurité concernant les toupies Utilisation et entretien des outils ÉlectroportatifsEntretien Consignes de sécurité pour table de toupillage Le plomb provenant des peintures à base de plomb Avertissements supplémentaires concernant la sécuritéSymbole Nom Désignation/Explication SymbolesTours, coups, vitesse en surface, orbites La vitesse augmente depuis le réglageSymboles suite Défonceuse Description fonctionnelle et spécificationsChoix DES Fers AssemblageMontage DES Fers Pour Enlever UN FER DE DéfonceuseConsignes d’utilisation Installation DE L’ADAPTATEUR DE Guide DE GabaritRamassage DES Poussières Mouvement DE PlongéeIndex DE Réglage Grossier Réglage Grossier DE LA ProfondeurBouton DE Réglage FIN Index DE Réglage FINAugmentation Progressive DE LA Profondeur DE Coupe Gchette ET Bouton DE Verrouillage SUR Marche Commande Électronique DE Variation DE VitesseSystème DE Démarrage Progressif TR/MIN ApplicationVitesse D’AVANCE Avance DE LA DéfonceuseMoulurage DE Chants Chant de bout endommage la pièceRamassage DE Poussière Lors DU Moulurage DE Chants ’emploi de l’outil avec ces accessoiresFixation DU Capuchon D’EXTRACTION DE Poussière Chant DE LA PièceCentrage DE LA SOUS-EMBASE ET DES Guides DE Gabarit Pièce DE Défonceuse Profil DU Gabarit DéportProfondeur Levier DE Préparation pour utilisation avec la table de toupillageTige DE Profondeur Bouton DE Désarmement DU Ressort Tourelle DE Butée DE ProfondeurDE Montage Utilisation avec la table de toupillageRéglage DE LA Profondeur Avance DE LA Pièce SUR UNE Table DE ToupillageNettoyage EntretienLubrification DE L’OUTIL Balais OU CharbonsAccessoires Capuchon d’extraction de poussière pour moulurage de chantsIndex à graduation métrique pour réglage grossier Seguridad del área de trabajo Seguridad eléctricaSeguridad personal Normas de seguridad para fresadoras MecánicasServicio de ajustes y reparaciones Instrucciones de seguridad para la mesa de fresadora Advertencias de seguridad adicionales Símbolos Símbolo Nombre Designación/explicaciónUn número más alto significa mayor velocidad Símbolos continuación Fresadoras Descripción funcional y especificacionesSelección DE Brocas EnsamblajeRemoción DE LA Broca DE Fresadora Cuidado DEL Mandril PortaherramientaCubierta a mangueras de aspiración de 1-1/4 y 1-1/2 FresadoraInstalación DEL Adaptador DE Guías DE Plantilla Acción DE PenetraciónIndicador DE Ajuste Grueso Ajuste DE Profundidad GruesoPomo DE Ajuste Fino Indicador DE Ajuste FinoProgresivamente MÁS Profundos Dispositivo DE Arranque Suave Interruptor Gatillo Y Botón DE Fijación EN EncendidoPosición DEL Dial AplicaciónVelocidad DE Avance Avance DE LA FresadoraConformado DE Bordes CortePara evitar Enredar Lea y entienda estasColocación DE LA Cubierta DE Extracción DE Polvo Cubierta DE Extracción DE PolvoGuiado DE LA Fresadora Centrado DE LA Subbase Y LAS Guías DE PlantillaGuía DE Fresadora DE Lujo Carcasa Palanca DE Preparación para la utilización con la mesa de fresadoraPalanca DE Fijación DE LA Profundidad Cierre DE Ajuste Grueso Botón DE Anulación DEL ResorteSujeción DE LA Fresadora a LA Placa DE Montaje Utilización en la mesa de fresadoraAjuste DE LA Profundidad Avance DE LA Pieza DE Trabajo Sobre UNA Mesa DE FresadoraMantenimiento ServicioLimpieza Cubierta de extracción de polvo con anillo de mejora AccesoriosBM 2610933969 09-12BM 2610933969 09-12.qxp 9/20/12 919 AM Remarques Notas 2610933969
Related manuals
Manual 56 pages 39.23 Kb