Black & Decker 492777-00 instruction manual Adjusting the Depth of CUT FIG. F, G & H, Soft Start

Page 10

492777-00 FS1200RP Router 2/6/06 1:02 PM Page 10

Carefully guide the cord in order to avoid accidentally cutting it.

ADJUSTING THE DEPTH OF CUT (FIG. F, G & H)

WARNING: Turn the router off and disconnect it from the power supply.

The depth of cut is the distance (X in figure F) between the depth stop bar (8) and the depth stop (28). The depth of cut can be set in two different ways as described below.

ADJUSTING THE DEPTH OF CUT USING THE SCALE (FIG. G)

WARNING: Turn the router off and disconnect it from the power supply.

Install the router bit as described previoisly.

Loosen the locking screw (29).

Pull the plunge lock lever (4) up.

Plunge the router down until the router bit touches the workpiece.

Push the plunge lock lever (4) down.

Move the depth stop bar (8) down against the depth stop using the depth stop adjuster (30). Reset the scale by aligning the zero marking (31) with the arrow (32).

Add the desired depth of cut to the starting position.

Move the depth stop bar (8) to the calculated position using the depth stop adjuster (30).

Tighten the locking screw (29).

Fine adjust using the adjusting knob (33).

Pull the plunge lock lever (4) up and let the router return to its original position.

After switching the router on, plunge it down and make the desired cut.

ADJUSTING THE DEPTH OF CUT USING A PIECE OF WOOD (FIG. H)

WARNING: Turn the router off and disconnect it from the power supply.

Install the router bit and plunge the router down as described previously.

Loosen the locking screw (29).

Move the depth stop bar (8) up using the depth stop adjuster (30).

Place a piece of wood with a thickness equal to the desired depth of cut between the depth stop (28) and the depth stop bar (8).

Move the depth stop bar (8) down against the wood using the depth stop adjuster (30).

Tighten the locking screw (29).

Fine adjust using the adjusting knob (33).

Remove the piece of wood.

Pull the plunge lock lever (4) up and let the router return to its original position.

After switching the router on, plunge it down and make the desired cut.

ADJUSTING THE TURRET DEPTH STOP (FIG. I)

WARNING: Turn the router off and disconnect it from the power supply.

After turning the turret depth stop to the desired setting, you can fine-adjust the depth stop to be used. If you want to make several cuts with a different depth of cut, adjust each of the depth stops.

• Turn the depth stop screw (34) up or down as required using a screwdriver.

SOFT START

Your router is equipped with a “soft start” feature which reduces the torque at start up and allows for increased control of the router.

ELECTRONIC SPEED CONTROL DIAL

The speed of your router is variable. Use the electronic speed control dial (3) to produce uniform cutting results in wood, plastics and aluminum. Use the lower settings for large diameter cutters and the higher settings for small diameter cutters.

CONTROL SPEED ELECTRONICS -CSE

Your router is equipped with CSE (control speed electronics)—as you load the router, the selected cutting speed does not slow down during normal use. The electronic control governs the motor and gives you a consistent finish to your work. Only under very heavy loading will the speed of the unit fall below the governed speed.

To set the router speed, rotate the speed control wheel (3). The higher the number the higher the speed.

10

Image 10
Contents Instruction Electrical Safety Work Area SafetyPersonal Safety Service Power Tool USE and CareSpecific Safety Rules Earthing terminal Features 102 PM 102 PM Bits Available AS Accessories not Supplied Attaching the Dust Extraction Adaptor FIG. C Installing and Removing a Router BIT FIG. aAttaching the Edge Guide FIG. B Attaching the Template Guide FIG. C & DAdjusting the Depth of CUT Using a Piece of Wood FIG. H Adjusting the Depth of CUT FIG. F, G & HAdjusting the Depth of CUT Using the Scale FIG. G Adjusting the Turret Depth Stop FIGUsing the Centering PIN FIG. E Using a Straight Edge AS a Guide FIG. JUsing the Template Guide FIG. D Switching on and OFFMaintenance Using the Router with Dust ExtractionProblem Possible Cause Solution Hints for Optimum USECovered Under OUR Warranty AccessoriesService Information Full TWO-YEAR Home USE Warranty HOW-TOMode ’EMPLOI Sécurité DU Lieu DE Travail Sécurité EN Matière D’ÉLECTRICITÉSécurité Personnelle Utilisation ET Entretien D’UN Outil ÉlectriqueRéparation Règles DE Sécurité SpécifiquesMoteur Caractéristiques 492777-00 FS1200RP Router 2/6/06 102 PM 102 PM Fraises Disponibles Comme Accessoires NON Comprises Fixation DU Guide DE Chant FIG. B Insertion ET Retrait D’UNE Fraise FIG. aInsertion Fixation DU Guide Pour Gabarit FIG. C ET DRéglage DE LA Profondeur DE Coupe SUR L’ÉCHELLE FIG. G Réglage DE LA Profondeur DE Coupe FIG. F, G ET HRéglage DE LA Butée D’ARRÊT DE LA Tourelle FIG Contrôle DE Vitesse Électronique CVE Fonction DE Démarrage SoupleMollette DE Contrôle Électronique DE LA Vitesse Utilisation D’UNE Règle Droite Comme Guide FIG. JConseils Pour UNE Utilisation Optimale Vitesse ET Taux DE RainurageUtilisation DE LA Défonceuse Avec L’ASPIRATEUR Fraises DE Toupie FIG. M NON ComprisesBlack & Decker au Problème possible Cause possible SolutionAccessoires EntretienGarantie Spéciale Avis Pour LES Entrepreneurs Peuvent PAS Être Couverts PAR Notre GarantieManual DE Seguridad EN EL Área DE Trabajo Seguridad EléctricaSeguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaMantenimiento Normas DE Seguridad EspecíficasReciprocaciones por minuto Características 492777-00 FS1200RP Router 2/6/06 102 PM 492777-00 FS1200RP Router 102 PM Brocas Disponibles Como Accesorios no SE Suministran Conexión DEL Adaptador Para Extracción DE Polvo FIG. C Instalación Y Extracción DE UNA Broca DE Rebajadora FIG. aConexión DE LA Guía DE Corte FIG. B Conexión DE LA Guía DE Corte FIG. C Y DAjuste DE LA Profundidad DE Corte CON LA Escala FIG. G Ajuste DE LA Profundidad DE Corte FIG. F, G Y HAjuste DEL Tope DE Profundidad CON Torreta FIG Control Electrónico DE Velocidad CSE Encendido SuaveDisco Electrónico DE Control DE Velocidad Utilice UNA Regla Como Guía FIG. JUSO DE LA Rebajadora CON UN Extractor DE Polvo USO DE LA RebajadoraVelocidad DE Alimentación Y Avance DEL Corte Consejos Para Optimizar EL USOProblema Causa posible Solución posible Detección DE ProblemasImportante Accesorios Nota Especial Sobre LA Garantíaa ContratistasPUEBLA, PUE CULIACAN, SIN MONTERREY, N.LGUADALAJARA, JAL MEXICO, D.F