Grizzly G0459P owner manual Service, Troubleshooting, Motor & Electrical

Page 29

SECTION 7: SERVICE

GZk^Zli]ZigdjWaZh]ddi^c\VcYegdXZYjgZh^ci]^hhZXi^dc^[VegdWaZbYZkZadehl^i]ndjgbVX]^cZ#>[ndj cZZYgZeaVXZbZcieVgihdgVYY^i^dcVa]Zael^i]VegdXZYjgZ!XVaadjgIZX]c^XVaHjeedgiVi*,%*)+".++(# Note:Please gather the serial number and manufacture date of your machine before calling.

Troubleshooting

Motor & Electrical

Symptom

Possible Cause

Possible Solution

 

 

 

 

 

 

Machine

does not

1.

Plug or receptacle is at fault or wired

1.

Test power plug and receptacle for good contact and

start or

a breaker

 

incorrectly.

 

correct wiring.

trips.

 

2.

Start capacitor is faulty.

2.

Test and replace capacitor as required (see photo,

 

 

 

 

 

 

 

Page 44).

 

 

3.

Motor connection is wired incorrectly.

3.

Correct motor wiring (see Page 45).

4.Power supply is faulty, or is switched OFF. 4. Make sure all hot lines and grounds are operational and have correct voltage on all legs.

 

5.

Centrifugal Switch is at fault.

5.

Adjust or replace the centrifugal switch.

 

6.

Motor ON button or ON/OFF switch is

6.

Replace faulty ON button or ON/OFF switch (see

 

 

faulty.

 

photo, Page 44).

 

7.

Motor is at fault.

7.

Test, repair or replace motor.

 

 

 

 

 

Machine has

1.

Motor or component is loose.

1.

Inspect, replace for stripped or damaged bolts/nuts,

vibration or noisy

 

 

 

and re-tighten with thread locking fluid.

operation.

2.

Motor fan is rubbing on fan cover.

2.

Replace dented fan cover, and replace loose or

 

 

 

 

 

damaged fan.

 

3.

V-belt(s) is worn or is loose.

3.

Inspect belt(s), replace as matched sets, and

 

 

 

 

re-tension.

 

4.

Pulley is loose.

4.

Remove pulley, replace shaft, pulley, setscrew, and

 

 

 

 

key as required, and realign.

 

5.

Motor bearings are at fault.

5.

Check bearings, replace motor or bearings as

 

 

 

 

required.

 

6.

Centrifugal switch.

6.

Normal snap/click sound on RPM wind down. No

 

 

 

 

problem exists.

 

 

 

 

 

Motor overheats.

1.

Motor overloaded.

1.

Reduce load on motor.

 

2.

Air circulation through the motor restricted.

2.

Clean off motor to provide normal air circulation.

Model G0459/G0459P (Mfg. 7/11+)

-27-

Image 29
Contents Drum Sander Ss ,EAD from Leadbased PAINTS Table of Contents Manual Accuracy IntroductionContact Info Machine DescriptionFront view, Model G0459 Identification$&+,1$7$ Drum Information $&+,1$7$ Conveyor Feed Rate 47 17.3 FPM Safety Instructions for Machinery SafetyZghWZXdbZVYhigVXidc# Children & BYSTANDERS. @ZZe XaYgZcAdditional Safety for Drum Sanders Availability Power SupplyFull-Load Current Rating Circuit RequirementsExtension Cords Grounding & Plug RequirementsMinimum Gauge Size 14 AWG 50 ftNeeded for Setup SetupUnpacking InventorySite Considerations Components and Hardware Needed Qty Installing Crank HandleMounting Connecting Power Power ConnectionDisconnecting Power Dust CollectionTo test run the machine Recommended AdjustmentsTest Run Operation Overview OperationsBasic Controls Disabling & Locking SwitchStock Inspection Requirements Sanding TipsTo set the depth of cut Depth of CutTo sand a workpiece To adjust the conveyor speedVariable Speed Sanding Choosing Sandpaper Paper ReplacementGrit Class Usage To change sandpaperG4679-Anti-Static Grounding Kit AccessoriesPRO-STICKSanding Pad Size ModelCleaning MaintenanceSchedule LubricationPillow Block Bearings Motor & Electrical ServiceTroubleshooting Sanding Operations Drums Tension Belt ServiceGauge Blocks To adjust V-belt tension Removal/ReplacementPulley Alignment To align the pulleysTensioning Conveyor Tensioning TrackingTracking To tension the conveyorDrum parallel to conveyor belt Model G0459/G0459P Mfg /11+ Drum AdjustmentsDrum perpendicular to feed direction To adjust the pillow block bearingsTo adjust the pressure rollers to the factory setting Factory SettingPressure Roller HeightTo calibrate the scale pointer Scale Pointer CalibrationTools Needed Qty Phillips Head Screwdriver Table Lift Screws To adjust the table lift screwsTo replace the conveyor belt Conveyor Belt ReplacementTo Step Drum sander disassembledBrass Shims IVWaZ To replace the motor brushes Changing Motor BrushesWiring Safety Instructions WiringCapacitor Feed motor110 VAC Wiring DiagramFrame PartsDescription Frame Parts ListDescription DrumConveyor Label Placement Conveyor Parts List10. 8dbbZcih Warranty Card99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns Order Hours a DAY