Black & Decker VP810 instruction manual General Safety Rules

Page 2

90538644 VP810 6/6/08 8:31 AM Page 2

General Safety Rules

WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1)Work area safety

a)Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b)Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c)Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2)Electrical safety

a)Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

b)Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c)Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

d)Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e)When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

3)Personal safety

a)Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tool may result in serious personal injury.

b)Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c)Avoid accidental starting. Ensure the switch is in the off-position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.

d)Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e)Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

f)Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should also be avoided.

g)If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust-related hazards.

4)Power tool use and care

a)Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was designed.

b)Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

2

Image 2
Contents Volt 3 Position Pivot Screwdriver VEA EL Español EN LA ContraportadaGeneral Safety Rules Specific Safety Rules Important Safety Instructions for Battery and Charger Safety Warnings and Instructions ChargingBattery CAP Information Important Charging Notes Safety Warnings and Instructions DrillingCharging Procedure Switch Removing and Installing BitsRemoving and Installing the Battery Operating InstructionsTWO Position Screwdriver MaintenanceAccessories TWO Position Screwdriver WarningsService Information Full TWO-YEAR Home USE Warranty Mode D’EMPLOI Règles de sécurité générales Conserver CES Directives90538644 VP810 6/6/08 831 AM Règles DE Sécurité Spécifiques Information Concernant LE Capuchon DU BLOC-PILEAvertissements de sécurité et directives chargement Procédure DE Charge Avertissements de sécurité et directives perçageRemarques Importantes DE Chargement Retrait ET Insertion DE LA Pile Mode d’emploiRetrait ET Insertion DES Embouts InterrupteurAvertissements Pour LE Tournevis À Deux Positions AccessoiresTournevis À Deux Positions EntretienDépannage 555326-7100 Normas generales de seguridad Conserve Estas Instrucciones90538644 VP810 6/6/08 831 AM Normas DE Seguridad Específicas Instrucciones y advertencias de seguridad carga Procedimiento DE Carga Instrucciones y advertencias de seguridad taladradoNotas Importantes Sobre LA Carga Instalación Y Retiro DE LA Batería Instrucciones de operaciónInstalación Y Retiro DE Puntas InterruptorAdvertencias Sobre DEL Destornillador DE DOS Posiciones Control DE TorsiónDestornillador DE DOS Posiciones MantenimientoDetección de problemas 90538644 VP810 6/6/08 831 AM MERIDA, YUC CULIACAN, SINMEXICO, D.F MONTERREY, N.L