Hitachi CR 18DV When the Blade is Broken, Maintenance and Inspection of SAW Blade Mount

Page 18
Semicircular slit Fig. 12
Fig. 10
Another blade Fig. 11

English

CAUTION: Be absolutely sure to keep the switch turned off and the battery removed to prevent any accident.

(2)After you have turned the holder sleeve in the direction of the arrow mark shown in Fig. 6 and secured it, turn the blade so it faces downward. The blade should fall out by itself. If the blade does't fall out, pull it out by hand.

CAUTION: Never touch the saw blade immediately after use. The metal is hot and can easily burn your skin.

WHEN THE BLADE IS BROKEN

Even when the saw blade is broken and remains inside the small slit of the plunger, it should fall out if you turn the holder sleeve in the direction of the

arrow mark, secure the holder sleeve, and face the

blade downward. If it doesn’t fall out itself, take it Blade out using the procedures explained below.

(1)If a part of the broken saw blade is sticking out of the small slit of the plunger, pull out the protruding part and take the blade out.

(2)If the broken saw blade is hidden inside the small slit, hook the broken blade using a tip of another saw blade and take it out. (Fig. 11)

MAINTENANCE AND INSPECTION OF SAW BLADE MOUNT

(1)After use, blow away sawdust, earth, sand, moisture, etc., with air or brush them away with a brush, etc., to ensure that the blade mount can function smoothly.

(2) Periodically lubricate the saw blade mount with

Holder

machine oil through the semicircular slit at a state

sleeve

where the holder sleeve is turned in the direction

 

of the arrow mark shown in Fig. 6. (Fig. 12)

 

Holder sleeve

Fig. 9

Holder sleeve

Machine

oil

NOTE:

18

If the saw blade mount is used without proper cleaning and lubrication, the rotation of the holder sleeve may be hampered by sawdust and

particles of dust, disabling you to remove the saw blade with your fingers.

In such a case, hold the periphery of the holder sleeve lightly using a pair of pliers and the like, and turn the holder sleeve to left and right little by little. After the saw blade has been successfully removed, be absolutely sure to clean it up with air, etc., carry out proper lubrication, and then check and see if the saw blade mount can function smoothly.

Image 18
Contents CR 18DV AvertissementContents Important Safety Information Meanings of Signal WordsSafety General Safety Rules for ALL Battery Operated ToolsEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Important Safety Instructions for Battery Charger Read ALL InstructionsEnglish Make Them Available to Other Users Owners of this Tool Name of Parts Functional DescriptionModel Cordless Reciprocating Saw CR18DVSpecifications Battery Charger UC 24YFAApplications Assembly and OperationRemoval and Installation Method of Battery Charging MethodEnglish Disconnect battery charger from the receptacle Indications of the pilot lampBefore USE Remove the battery from the battery chargerHow to make the batteries perform longer Regarding electric discharge in case of new batteries, etcPrior to Operation Mounting the bladeDismounting the blade When the Blade is Broken Maintenance and Inspection of SAW Blade MountSwitch operation HOW to USE the Cordless Reciprocating SAWConfirm that the battery is mounted correctly Moving the baseCutting metallic materials Cutting lumberSawing curved lines Plunge cutting Maintenance and Inspection Service parts list Disposal of the exhausted batteryService and repairs Check for DustModifications English English Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTSecurite Conserver CES InstructionsAvertissement Lire et coxmprendre toutes les instructions Avertissement Regles DE Securite Specifiques ET Symboles Manipuler l’outil motorisé avec précaution Ne pas essuyer les parties en plastique avec du solvantLire Tout CE Mode Demploi Français Français NOM DES Parties Description FonctionnelleModele Scie alternative à batterie CR18DVChargeur de batterie UC24YFA Chargeur de batterie UC 24YFAMéthode DE Retrait ET D’INSTALLATION DE LA Batterie Méthode DE RechargeBrancher la fiche du chargeur de batterie dans la prise Insérer la batterie dans le chargeur de batterieRecharge Precaution Débrancher le chargeur de batterie de la priseAvant L’UTILISATION Retirer la batterie du chargeur de batterieComment prolonger la durée de vie des batteries Avant L’OPERATON Montage de la lameDémontage de la lame SI LA Lame EST CasseeEntretien ET Inspection DE LA Monture DE Lame Déplacement du socle Comment Utiliser LA Scie Alternative À Batterie’assurer que la batterie est montée Correctement Fonctionnement de l’interrupteur Coupe de métaux Appuyer le socle fermement contre la pièce Coupe de bois Sciage de lignes courbesAttaque en plein bois Français Entretien ET Inspection Rangement Vérifier s’il y a de la poussièreMise au rebut d’une batterie usée Entretien et réparationLista de repuestos ModificacionesFrançais Français Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónSeguridad Guarde Estas InstruccionesAdvertencia Lea y entienda todas las instrucciones Advertencia Normas Y Símbolos Específicos DE Seguridad Utilice la herramienta correctaManeje correctamente la herramienta Maneje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeLEA Todas LAS Instrucciones Español Español Nomenclatura Descripción FunctionalModelo Sierra reciprocante a batería CR18DVEspecificaciones Cargador de baterías UC 24YFAMétodo DE Extracción E Instalación DE LA Batería Montaje Y OperaciónAplicaciones Método DE CargaInserte la batería en el cargador de baterías CargaDesconecte el cargador de baterías del tomacorriente PrecauciónDescarga eléctrica en caso de baterías nuevas, etc Antes DE LA UtilizaciónExtraiga la batería del cargador de baterías Forma de hacer que las baterías duren másAntes DE LA Operación Montaje de la hojaDesmontaje de la hoja Cuando SE Rompa LA HojaCerciórese de que la batería esté correctamente instalada Como Usar LA Sierra Sable a BateríaMoviendo la base CarreraOperación del interruptor Corte de materiales metálicosCorte de madera Corte de líneas curvadasCorte por penetración Español Mantenimiento E Inspección Almacenamiento Comprobación del polvoEliminación de las baterías agotadas Mantenimiento y reparaciónListe des pièces de rechange Español Español Page Page Page Hitachi Koki Canada Co