Black & Decker BDCDMT120-2, BDCDMT120FL Operating Drill/Screwdriver attachment, Screw driving

Page 10

Installing and removing attachments - Figure G

G

WARNING: Shock hazard. Under no circumstances should

 

this product be used near water.

 

WARNING: Burn hazard. Moving parts within the Power

 

Unit become hot during use. Avoid contact with moving parts

 

within Power Unit when removing and installing accessories.

 

WARNING: Before assembly, lock the Power Unit by

 

setting the forward/reverse slider (7) to the center position and

 

remove the battery from the Power Unit. Remove any accessory

 

from the attachment before removing or installing the attachment.

 

WARNING: To reduce the risk of injury, do not place fingers or other objects inside the Power Unit, other than the attachments designed to work with the Power Unit.

•Lock the Power Unit by setting the forward/reverse slider (7) to the center position.

•To remove an attachment, depress the release button (9) and take the attachment off the tool.

•To fit an attachment, line it up with the tool as shown and push it onto the Power Unit until it snaps into place and an audible click is heard.

•Ensure attachment is securely attached by gently pulling it away from the Power Unit.

NOTE: Only use attachments that are specifically designed for and compatible with the Power Unit.

NOTE: Refer to individual attachment instruction manuals for specific safety warnings and operating instructions before operating attachments with the Power Unit.

Operating: Drill/Screwdriver attachment

Safety Warnings and Instructions: Drills

1. Hold drill firmly with one hand on the grip and the other hand on the bottom of the battery pack unless an auxillary handle has been supplied with the tool. Use auxillary handle if supplied with the tool.

2. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly.

WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall. Grip the drill firmly with both hands to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting.

WARNING: Let the tool work at its own pace. Do not overload.

WARNING: Before drilling into walls, floors or ceilings, check for the location of wiring and pipes.

Fitting and removing a drill bit or screwdriver bit

The drill/screwdriver attachment (11) is fitted with a keyless chuck (12) to allow for an easy exchange of bits.

• Lock the tool by setting the forward/reverse slider (7) to the center position.

• Open the chuck by turning the front part clockwise with one hand while holding the rear part with the other.

• Insert the bit shaft into the chuck.

• Firmly tighten the chuck by turning the front part counterclockwise.

• To remove the screwdriver bit from the holder, lift the bit from the recess.

• To store the screwdriver bit, firmly push it into the holder (10).

screw driving

•Always use the correct type and size of screwdriver bit.

•If screws are difficult to tighten, try applying a small amount of washing liquid or soap as a lubricant.

•Always hold the tool and screwdriver bit in a straight line with the screw.

•For driving fasteners, the reversing button should be pushed to the left. Use reverse (button pushed to the right) for removing fasteners. When moving from forward to reverse, or vice versa, always release the trigger switch first.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Save this manual for Future reference Catalog Number BDCDMT112 12V MAX BDCDMT120 20V MAXVEA EL ESPA-OL EN LA Contraportada Safety Guidelines Definitions Work Area SafetySpecific Safety Rules Always Wear Certified Safety EQUIPMENT  SymbolsImportant Safety Instructions for Battery Chargers FUNCTIONAL DESCRIPTIONRead all Instructions Minimum Gauge for Cord Sets Volts12volt max* Charging Procedure 20volt Max** Charging Procedure Operating Power Unit Trigger Switch & forward/Reverse sliderOperating Drill/Screwdriver attachment Installing and removing attachments Figure GSafety Warnings and Instructions Drills Fitting and removing a drill bit or screwdriver bitTorque Control figure Make sure switch turns drill on and off Drilling in WoodKeyless Chuck figure H On-board bit storageTroubleshooting Rbrc SealSee ‘Tools-Electric’ Service Information Full Two-Year Home Use WarrantyFor Service & Sales Yellow PagesMode D’EMPLOI De catalogue BDCDMT112 12V MAX BDCDMT120 20V MAXLignes directrices en matière de sécurité définitions Modifiées correspondant à la prisePage Règles de sécurité spécifiques Symboles Description FonctionnelleAvertissement Lire toutes les directives Tension Longueur totale du cordon en pieds12volt max* Procédure de charge Remarques importantes pour le chargement 12volt max* Insertion et retrait du bloc-piles de l’outil20volt Max** Procédure de charge Bloc-piles laissé dans le chargeur20volt Max** Insertion et retrait du bloc-piles de l’outil Installation ET Retrait DES Modules Figure GDétente ET Commutateur Coulissant AVANT/ARRIÈRE Avertissement de sécurité et directives perceuses VissageRangement intégré des mèches Réglage du couple figurePerçage Perçage DU Métal DépannagePerçage DU Bois EntretienLe sceau Rbrc Information sur les réparationsPage Manual DE Instrucciones Catálogo N BDCDMT112 12V MAX BDCDMT120 20V MAXPautas DE SEGURIDAD/DEFINICIONES Page Normas de seguridad específicas Descripción de las funciones SímbolosAdvertencia Lea todas las instrucciones AmperajeRecomendaciones con respecto al almacenamiento 12volt max* Procedimiento de cargaNotas importantes sobre la carga Herramienta20volt Max** Procedimiento de carga Instalación Y Extracción DE Aditamentos Figura G Para instalar el paquete de baterías Inserte elPara extraer el paquete de baterías Presione el botón Precaución Riesgo de descarga eléctrica. BajoColocación Y Extracción DE UNA Broca O UNA Punta DestornilladoEspacio en la herramienta para guardar brocas Portabrocas sin llave figura HAjuste del control de torsión figura TaladradoMantenimiento El sello Rbrc Información de mantenimientoGarantía completa de dos años para uso en el hogar Reemplazo DE LAS Etiquetas DE AdvertenciaEsta Garantia no Aplica Cuando Solamente Para Propositos DE Mexico

BDCDMT120IA, BDCDMT120C, BDCDMT120FL, BDCDMT120-2 specifications

The Black & Decker BDCDMT120-2, BDCDMT120FL, BDCDMT120C, and BDCDMT120IA are versatile and reliable power tools designed to cater to a range of home improvement tasks. These tools embody Black & Decker's commitment to quality, functionality, and user-friendliness across various DIY and professional applications.

The BDCDMT120-2 is a 20V Max Lithium-Ion compact cordless drill/driver that provides exceptional power and versatility. With its lightweight design, it offers enhanced maneuverability, making it excellent for both overhead and tight-space tasks. The drill features a two-speed transmission, allowing users to choose between 0-650 RPM for high-speed drilling or 0-450 RPM for increased torque. Additionally, the 11-position clutch helps prevent stripping screws and provides added control for precise tasks.

The BDCDMT120FL is an innovative oscillating multi-tool that stands out for its versatility. It comes equipped with a tool-free accessory change system, enabling quick transitions between sanding, cutting, and scraping tasks. Powered by a 20V Max Lithium-Ion battery, it ensures robust performance, and its variable speed control allows users to adjust the speed according to the specific application needs. With its ergonomic design, users can work comfortably for extended periods without fatigue.

The BDCDMT120C is a 20V Max cordless circular saw that delivers the power and precision required for cutting through various materials. Its 5-1/2 inch blade enables a maximum cutting depth of 1-5/8 inches, making it ideal for wood, plywood, and other materials. The saw features an integrated laser guide that aids in achieving accurate cuts, along with a lightweight design for ease of handling. Its base plate can be adjusted for bevel cuts, adding to its versatility.

Lastly, the BDCDMT120IA is a compact and robust impact driver that significantly enhances drilling and fastening efficiency. With a torque of up to 1,400 in-lbs and a maximum speed of 2,900 RPM, it easily drives screws through the toughest materials. The built-in LED work light illuminates dark workspaces, ensuring precision in low-light conditions. Its ergonomic grip further enhances control, allowing users to work comfortably during extended periods.

Together, these Black & Decker tools form a comprehensive solution for tackling a variety of home improvement projects. Their thoughtful design, advanced features, and powerful performance make them essential additions to any DIYer’s toolkit. Whether for drilling, cutting, or detailed work, these power tools provide the reliability and efficiency that Black & Decker is known for, empowering users to complete their projects with confidence.
Top Page Image Contents