Black & Decker BDCDMT120C Operating Power Unit, Trigger Switch & forward/Reverse slider

Page 9

3.If the battery pack does not charge properly:

a.Check current at receptacle by plugging in a lamp or other appliance

b.Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights.

c.Move charger and battery pack to a location where the surrounding air temperature is approximately 65°F - 75°F (18°- 24°C).

d.If charging problems persist, take the tool, battery pack and charger to your local service center.

4.The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you desire with no adverse affect on the battery pack.

5.Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

6.Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard. Do not allow any liquid to get inside charger. Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a service center for recycling.

20volt Max** Installing and Removing the Battery Pack

From the power unit

 

E

Always ensure the forward/reverse slider (7) is in the center position

when installing and removing batteries.

 

WARNING: Make certain the lock-off button is engaged to

 

prevent switch actuation before removing or installing battery.

 

To install battery pack: Insert battery pack into the Power

 

Unit until an audible click is heard (Figure E). Make sure battery

 

pack is fully seated and fully latched into position.

 

To remove battery pack: Depress the battery release button

 

(6) as shown in Figure F and pull battery pack out of the Power Unit.

 

 

 

 

F

Operating: Power Unit

 

Trigger Switch & forward/Reverse slider

 

The forward/reverse slider (7) is used to control the direction the

 

chuck (12) spins - foward to drive screws, reverse to remove screws.

 

It is located above the variable speed trigger (8). To reverse the

 

motor, release the trigger FIRST, then push the slider to the right

 

hand side of the tool when viewing from the rear. After any reversing

 

operations, return lever to the forward position. Never change the

 

direction of rotation while the motor is running.

 

• The Power Unit is turned ON and OFF by pulling and releasing the trigger. The farther the trigger is depressed, the higher the speed of the Power Unit.

• A forward/reverse control slider determines the direction of the tool.

• To select forward rotation, release the trigger switch and depress the forward/reverse control button to the left.

• To select reverse, depress the forward/reverse control button to the right.

NOTE: When changing the position of the control button, be sure the trigger is released.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Catalog Number BDCDMT112 12V MAX BDCDMT120 20V MAX Save this manual for Future referenceVEA EL ESPA-OL EN LA Contraportada Work Area Safety Safety Guidelines DefinitionsSpecific Safety Rules Symbols Always Wear Certified Safety EQUIPMENT FUNCTIONAL DESCRIPTION Important Safety Instructions for Battery ChargersMinimum Gauge for Cord Sets Volts Read all Instructions12volt max* Charging Procedure 20volt Max** Charging Procedure Trigger Switch & forward/Reverse slider Operating Power UnitSafety Warnings and Instructions Drills Installing and removing attachments Figure GOperating Drill/Screwdriver attachment Fitting and removing a drill bit or screwdriver bitKeyless Chuck figure H Make sure switch turns drill on and off Drilling in WoodTorque Control figure On-board bit storageRbrc Seal TroubleshootingFor Service & Sales Service Information Full Two-Year Home Use WarrantySee ‘Tools-Electric’ Yellow PagesDe catalogue BDCDMT112 12V MAX BDCDMT120 20V MAX Mode D’EMPLOIModifiées correspondant à la prise Lignes directrices en matière de sécurité définitionsPage Règles de sécurité spécifiques Description Fonctionnelle SymbolesAvertissement Tension Longueur totale du cordon en pieds Lire toutes les directives12volt max* Procédure de charge 12volt max* Insertion et retrait du bloc-piles de l’outil Remarques importantes pour le chargementBloc-piles laissé dans le chargeur 20volt Max** Procédure de chargeInstallation ET Retrait DES Modules Figure G 20volt Max** Insertion et retrait du bloc-piles de l’outilDétente ET Commutateur Coulissant AVANT/ARRIÈRE Vissage Avertissement de sécurité et directives perceusesRéglage du couple figure Rangement intégré des mèchesPerçage Perçage DU Bois DépannagePerçage DU Métal EntretienInformation sur les réparations Le sceau RbrcPage Catálogo N BDCDMT112 12V MAX BDCDMT120 20V MAX Manual DE InstruccionesPautas DE SEGURIDAD/DEFINICIONES Page Normas de seguridad específicas Símbolos Descripción de las funcionesAdvertencia Amperaje Lea todas las instrucciones12volt max* Procedimiento de carga Recomendaciones con respecto al almacenamientoHerramienta Notas importantes sobre la carga20volt Max** Procedimiento de carga Para extraer el paquete de baterías Presione el botón Para instalar el paquete de baterías Inserte elInstalación Y Extracción DE Aditamentos Figura G Precaución Riesgo de descarga eléctrica. BajoDestornillado Colocación Y Extracción DE UNA Broca O UNA PuntaAjuste del control de torsión figura Portabrocas sin llave figura HEspacio en la herramienta para guardar brocas TaladradoMantenimiento Información de mantenimiento El sello RbrcReemplazo DE LAS Etiquetas DE Advertencia Garantía completa de dos años para uso en el hogarEsta Garantia no Aplica Cuando Solamente Para Propositos DE Mexico

BDCDMT120IA, BDCDMT120C, BDCDMT120FL, BDCDMT120-2 specifications

The Black & Decker BDCDMT120-2, BDCDMT120FL, BDCDMT120C, and BDCDMT120IA are versatile and reliable power tools designed to cater to a range of home improvement tasks. These tools embody Black & Decker's commitment to quality, functionality, and user-friendliness across various DIY and professional applications.

The BDCDMT120-2 is a 20V Max Lithium-Ion compact cordless drill/driver that provides exceptional power and versatility. With its lightweight design, it offers enhanced maneuverability, making it excellent for both overhead and tight-space tasks. The drill features a two-speed transmission, allowing users to choose between 0-650 RPM for high-speed drilling or 0-450 RPM for increased torque. Additionally, the 11-position clutch helps prevent stripping screws and provides added control for precise tasks.

The BDCDMT120FL is an innovative oscillating multi-tool that stands out for its versatility. It comes equipped with a tool-free accessory change system, enabling quick transitions between sanding, cutting, and scraping tasks. Powered by a 20V Max Lithium-Ion battery, it ensures robust performance, and its variable speed control allows users to adjust the speed according to the specific application needs. With its ergonomic design, users can work comfortably for extended periods without fatigue.

The BDCDMT120C is a 20V Max cordless circular saw that delivers the power and precision required for cutting through various materials. Its 5-1/2 inch blade enables a maximum cutting depth of 1-5/8 inches, making it ideal for wood, plywood, and other materials. The saw features an integrated laser guide that aids in achieving accurate cuts, along with a lightweight design for ease of handling. Its base plate can be adjusted for bevel cuts, adding to its versatility.

Lastly, the BDCDMT120IA is a compact and robust impact driver that significantly enhances drilling and fastening efficiency. With a torque of up to 1,400 in-lbs and a maximum speed of 2,900 RPM, it easily drives screws through the toughest materials. The built-in LED work light illuminates dark workspaces, ensuring precision in low-light conditions. Its ergonomic grip further enhances control, allowing users to work comfortably during extended periods.

Together, these Black & Decker tools form a comprehensive solution for tackling a variety of home improvement projects. Their thoughtful design, advanced features, and powerful performance make them essential additions to any DIYer’s toolkit. Whether for drilling, cutting, or detailed work, these power tools provide the reliability and efficiency that Black & Decker is known for, empowering users to complete their projects with confidence.
Top Page Image Contents