Grizzly owner manual Model G0759

Page 1

MODEL G0759

MILL/DRILL

w/STAND & DRO

MANUAL INSERT

The Model G0759 is the same machine as the Model G0704 except the Model G0759 has a 3-axis DRO. Besides the differences noted in this insert, all other content in the Model G0704 owner's manual applies to this machine. Before operating your new machine, you MUST read and understand this insert, the entire Model G0704 manual, and the DRO manual to reduce the risk of injury when using this machine.

If you have any further questions about this manual insert or the differences between the Model G0759 and the Model G0704, contact our Technical Support at (570) 546-9663 or email techsupport@grizzly.com.

COPYRIGHT © FEBRUARY, 2014 BY GRIZZLY INDUSTRIAL, INC., REVISED APRIL, 2014 (TS)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MANUFACTURED SINCE 1/14) #TS16276 PRINTED IN CHINA

Image 1

Contents Model G0759 Machine Data Sheet Table Info Column & Stand Description Electrical Box Headstock Description Chip Guard Labels Model G0704 MILL/DRILL with Stand Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description Identification G0704 electronic controls identification Electronic Controls IdentificationModel G0704 DRILL/MILL with Stand 50 2250 RPM Accessories Included Safety Instructions for Machinery SafetyChILdREN & BYsTANdERs. Keepchildrenand Maintain Power CORds. When disconnectAdditional Safety for Mill/Drills Power Supply 50 ft Minimum Gauge Size 16 AWGUnpacking Needed for SetupDescription Qty Inventory Contents QtyNot Shown Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Weight LoadMoving & Placing Machine Example of a direct mount setupBolting to Concrete Floors Mounting to Shop FloorTo install the drill chuck onto the arbor AssemblyDrill Chuck Arbor To assemble your machineConnecting Power Power ConnectionTo test run and break-in the spindle bearings Test Run & Spindle Break-inOperation Overview OperationsSpeed Range Selector Knob Selects low range Basic ControlsDigital readout unit controls Model G0704 Mfg. Since 08/11 To use the digital readout Digital Readout UnitTo determine the needed spindle speed Calculating Spindle SpeedTo set the spindle speed Spindle Speed DirectionSpindle Height Controls Changing Spindle Position Using Quill Feed LeversDrill Chuck To install the drill chuck and arborLoading Tooling To install the toolingTo remove the collet To raise or lower the headstock Headstock Travel Axis and RotationTo tilt the headstock to the left or right Longitudinal Feed Table TravelCross Feed H8177-Worktable with Angle H8179G5684-R-8 Vertical Collet Rack G8683Z-Mini Shop Fox Mobile Base G9322-Boring Head Combo SetH5685-4Rotary Table G5758-Tilt x Model G9512 T-Slot NutsSchedule MaintenanceLubrication To lubricate the leadscrews Tools Needed QtyHandwheel gears Troubleshooting ServiceSymptom Possible Cause Possible Solution To adjust the headstock gibs To adjust the table gibsGibs To adjust the Y-axis leadscrew nut Battery ReplacementTo adjust the X-axis leadscrew To replace the digital readout unit batteryTo inspect and replace the motor brushes Motor ServiceWiring Safety Instructions WiringWiring Diagram Side panel Rear panelColumn Breakdown PartsColumn Parts List 80-1 92V2 Electrical Box Breakdown & Parts ListHeadstock Breakdown Headstock Parts List Description Chip Guard Breakdown & Parts ListLabels Breakdown & Parts List Model G0704 Mfg. Since 08/11 Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns