Grizzly G0759 owner manual Labels

Page 10

Labels

301302

303

312

309

310

308

305	304

307

306

311

REF	PART #	DESCRIPTION

301	P0759301	READ MANUAL LABEL
302	P0759302	SAFETY GLASSES LABEL
303	P0759303	MACHINE ID LABEL
304	P0759304	HIGH/LOW SPEED LABEL
305	P0759305	GRIZZLY PUTTY TOUCH-UP PAINT
306	P0759306	MODEL NUMBER LABEL

REF	PART #	DESCRIPTION

307	P0759307	GRIZZLY GREEN TOUCH-UP PAINT
308	P0759308	CUTTER WARNING LABEL
309	P0759309	ENTANGLEMENT LABEL
310	P0759310	AVOID OVERHEATING LABEL
311	P0759311	GRIZZLY.COM LABEL
312	P0759312	ELECTRICITY LABEL

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

-10-	Model G0759 (Mfd. Since 1/14)

Image 10

Contents Model G0759 Machine Data Sheet Table Info Column & Stand Description Electrical Box Headstock Description Chip Guard Labels Model G0704 MILL/DRILL with Stand Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description Identification Electronic Controls Identification G0704 electronic controls identificationModel G0704 DRILL/MILL with Stand 50 2250 RPM Accessories Included Safety Safety Instructions for MachineryMaintain Power CORds. When disconnect ChILdREN & BYsTANdERs. KeepchildrenandAdditional Safety for Mill/Drills Power Supply Minimum Gauge Size 16 AWG 50 ftUnpacking Needed for SetupDescription Qty Inventory Contents QtyNot Shown Before cleaning, gather the following CleanupBasic steps for removing rust preventative Weight Load Site ConsiderationsExample of a direct mount setup Moving & Placing MachineMounting to Shop Floor Bolting to Concrete FloorsDrill Chuck Arbor AssemblyTo install the drill chuck onto the arbor To assemble your machinePower Connection Connecting PowerTest Run & Spindle Break-in To test run and break-in the spindle bearingsOperations Operation OverviewBasic Controls Speed Range Selector Knob Selects low rangeDigital readout unit controls Model G0704 Mfg. Since 08/11 Digital Readout Unit To use the digital readoutCalculating Spindle Speed To determine the needed spindle speedSpindle Speed Direction To set the spindle speedChanging Spindle Position Using Quill Feed Levers Spindle Height ControlsTo install the drill chuck and arbor Drill ChuckLoading Tooling To install the toolingTo remove the collet To raise or lower the headstock Headstock Travel Axis and RotationTo tilt the headstock to the left or right Longitudinal Feed Table TravelCross Feed H8177-Worktable with Angle H8179G5684-R-8 Vertical Collet Rack G8683Z-Mini Shop Fox Mobile Base G9322-Boring Head Combo SetH5685-4Rotary Table Model G9512 T-Slot Nuts G5758-Tilt xSchedule MaintenanceLubrication Tools Needed Qty To lubricate the leadscrewsHandwheel gears Service TroubleshootingSymptom Possible Cause Possible Solution To adjust the headstock gibs To adjust the table gibsGibs To adjust the X-axis leadscrew Battery ReplacementTo adjust the Y-axis leadscrew nut To replace the digital readout unit batteryMotor Service To inspect and replace the motor brushesWiring Wiring Safety InstructionsWiring Diagram Rear panel Side panelParts Column BreakdownColumn Parts List Electrical Box Breakdown & Parts List 80-1 92V2Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List DescriptionLabels Breakdown & Parts List Model G0704 Mfg. Since 08/11 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns