Grizzly G0759 owner manual Loading Tooling, To install the tooling, To remove the collet

Page 42

Loading Tooling

Your Model G0704 features an R-8 spindle taper, which gives the freedom to use standard R-8 cutting tools and collets. These optional collets come in many sizes, typically ranging from 116" to 78" and 3mm to 20mm, and should be matched to your cutting tool shank size.

To install the tooling:

1.DISCONNECT MILL/DRILL FROM POWER!

2.Remove the drawbar cap.

3.Carefully clean the surface of the tooling and spindle taper. Ensure that it is free of debris and is lightly oiled.

4.If you are using a cutting tool and collet, insert the cutting tool into the collet, then insert the collet up into the spindle taper, making sure the slot in the collet lines up with the pin in the spindle.

if you are using a cutting tool that installs directly into the spindle, insert the tool into the spindle taper, making sure the slot in the tool lines up with the pin in the spindle.

5.slide the tooling upward until it makes con- tact with the drawbar threads.

6.Hand thread the drawbar into the tooling until the tooling draws up into the spindle taper.

7.Use the included spindle pin to prevent the spindle from turning while you use an 8mm wrench to tighten the drawbar.

Note: Do not overtighten the drawbar. Overtightening makes collet removal difficult and will damage the drawbar threads, collet, and the spindle taper. Keep in mind that the taper keeps the collet and tool in place. The drawbar simply aids in seating the taper.

-30-

To remove the collet:

1.DISCONNECT MILL/DRILL FROM POWER!

2.Remove the drawbar cap.

3.Lock the quill in place with the quill lock lever.

4.Use the included spindle pin to prevent the spindle from turning while you use an 8mm wrench to loosen the drawbar 2–3 turns. DO NOT continue loosening the drawbar without supporting the collet or it will fall from the spindle.

LACERATION HAZARD! Leading edges of end mills and other cutting tools can be very sharp. Protect your hands with gloves or a shop towel when handling.

NOTICE

The Model G0704 drawbar will extract the arbor from the spindle. Once the arbor or collet has broken free from the spindle taper, be sure to properly support it while continuing to loosen the drawbar. Failure to properly support the arbor or collet while loosening the drawbar will result in the arbor or collet falling out of the spindle, causing damage to machine components.

5.protect the table surface with a piece of cardboard and hold the cutter/tool with a shop towel to prevent it from falling out of the collet. Continue loosening the drawbar until the collet is freed from the spindle.

Model G0704 (Mfg. Since 08/11)

Image 42
Contents Model G0759 Machine Data Sheet Table Info Column & Stand Description Electrical Box Headstock Description Chip Guard Labels Model G0704 MILL/DRILL with Stand Page Table of Contents Introduction Manual Accuracy Contact InfoMachine Description Identification Electronic Controls Identification G0704 electronic controls identificationModel G0704 DRILL/MILL with Stand 50 2250 RPM Accessories Included Safety Safety Instructions for MachineryMaintain Power CORds. When­ disconnect ChILdREN & BYsTANdERs. Keep­children­and­Additional Safety for Mill/Drills Power Supply Minimum Gauge Size 16 AWG 50 ftNeeded for Setup UnpackingDescription Qty Contents Qty InventoryNot Shown Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Weight Load Site ConsiderationsExample of a direct mount setup Moving & Placing MachineMounting to Shop Floor Bolting to Concrete FloorsDrill Chuck Arbor AssemblyTo install the drill chuck onto the arbor To assemble your machinePower Connection Connecting PowerTest Run & Spindle Break-in To test run and break-in the spindle bearingsOperations Operation OverviewBasic Controls Speed Range Selector Knob Selects low rangeDigital readout unit controls Model G0704 Mfg. Since 08/11 Digital Readout Unit To use the digital readoutCalculating Spindle Speed To determine the needed spindle speedSpindle Speed Direction To set the spindle speedChanging Spindle Position Using Quill Feed Levers Spindle Height ControlsTo install the drill chuck and arbor Drill ChuckTo install the tooling Loading ToolingTo remove the collet Headstock Travel Axis and Rotation To raise or lower the headstockTo tilt the headstock to the left or right Table Travel Longitudinal FeedCross Feed H8179 H8177-Worktable with AngleG5684-R-8 Vertical Collet Rack G9322-Boring Head Combo Set G8683Z-Mini Shop Fox Mobile BaseH5685-4Rotary Table Model G9512 T-Slot Nuts G5758-Tilt xMaintenance ScheduleLubrication Tools Needed Qty To lubricate the leadscrewsHandwheel gears Service TroubleshootingSymptom Possible Cause Possible Solution To adjust the table gibs To adjust the headstock gibsGibs To adjust the X-axis leadscrew Battery ReplacementTo adjust the Y-axis leadscrew nut To replace the digital readout unit batteryMotor Service To inspect and replace the motor brushesWiring Wiring Safety InstructionsWiring Diagram Rear panel Side panelParts Column BreakdownColumn Parts List Electrical Box Breakdown & Parts List 80-1 92V2Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List DescriptionLabels Breakdown & Parts List Model G0704 Mfg. Since 08/11 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns