Grizzly G0759 owner manual Inventory, Contents Qty, Not Shown

Page 26

Inventory

The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them.

If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store.

Contents

Qty

A.

mill/Drill w/Stand

1

B.

open End Combo Wrench 17/19

1

C.

open End Combo Wrench 8/10

1

D.

bottle for Oil

1

E.

tool Box

1

F.

large Handwheel Handle

1

G.

Small Handwheel Handles

3

H.

t-Bolts M10-1.5 x 60 (vise mounting)

2

 

Flat Washers 10mm (vise mounting)

2

 

hex Nuts M10-1.5 (vise mounting)

2

I.

drill Chuck

1

J.

Chuck Key

1

K.

Phillips Screwdriver

1

L.

Flat Screwdriver

1

M.

arbor B16 x R8

1

N.

hex Wrench Set 2, 3, 4, 5, & 6mm

1 ea.

O.

Spindle Pin

1

Not Shown:

 

 

hex Bolts M10-1.5 x 50

4

 

Flat Washers 10mm

4

-14-

A

Figure 4. G0704 out of the crate.

NOTICE

If you cannot find an item on this list, care- fully check around/inside the machine and packaging materials. Often, these items get lost in packaging materials while unpack- ing or they are pre-installed at the factory.

D

B

E

 

 

C

 

M

 

 

K L

 

N

O

 

 

 

F

J

I

H

G

 

 

Figure 5. Inventory.

Model G0704 (Mfg. Since 08/11)

Image 26
Contents Model G0759 Machine Data Sheet Table Info Column & Stand Description Electrical Box Headstock Description Chip Guard Labels Model G0704 MILL/DRILL with Stand Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification Electronic Controls Identification G0704 electronic controls identificationModel G0704 DRILL/MILL with Stand 50 2250 RPM Accessories Included Safety Safety Instructions for MachineryMaintain Power CORds. When­ disconnect ChILdREN & BYsTANdERs. Keep­children­and­Additional Safety for Mill/Drills Power Supply Minimum Gauge Size 16 AWG 50 ftDescription Qty Needed for SetupUnpacking Not Shown Contents QtyInventory Basic steps for removing rust preventative CleanupBefore cleaning, gather the following Weight Load Site ConsiderationsExample of a direct mount setup Moving & Placing MachineMounting to Shop Floor Bolting to Concrete FloorsDrill Chuck Arbor AssemblyTo install the drill chuck onto the arbor To assemble your machinePower Connection Connecting PowerTest Run & Spindle Break-in To test run and break-in the spindle bearingsOperations Operation OverviewBasic Controls Speed Range Selector Knob Selects low rangeDigital readout unit controls Model G0704 Mfg. Since 08/11 Digital Readout Unit To use the digital readoutCalculating Spindle Speed To determine the needed spindle speedSpindle Speed Direction To set the spindle speedChanging Spindle Position Using Quill Feed Levers Spindle Height ControlsTo install the drill chuck and arbor Drill ChuckTo remove the collet To install the toolingLoading Tooling To tilt the headstock to the left or right Headstock Travel Axis and RotationTo raise or lower the headstock Cross Feed Table TravelLongitudinal Feed G5684-R-8 Vertical Collet Rack H8179H8177-Worktable with Angle H5685-4Rotary Table G9322-Boring Head Combo SetG8683Z-Mini Shop Fox Mobile Base Model G9512 T-Slot Nuts G5758-Tilt xLubrication MaintenanceSchedule Tools Needed Qty To lubricate the leadscrewsHandwheel gears Service TroubleshootingSymptom Possible Cause Possible Solution Gibs To adjust the table gibsTo adjust the headstock gibs To adjust the X-axis leadscrew Battery ReplacementTo adjust the Y-axis leadscrew nut To replace the digital readout unit batteryMotor Service To inspect and replace the motor brushesWiring Wiring Safety InstructionsWiring Diagram Rear panel Side panelParts Column BreakdownColumn Parts List Electrical Box Breakdown & Parts List 80-1 92V2Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List DescriptionLabels Breakdown & Parts List Model G0704 Mfg. Since 08/11 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns