Grizzly G0759 owner manual Table Travel, Longitudinal Feed, Cross Feed

Page 44

Table Travel

The mill/drill table can be moved in the longitudi- nal (X-axis) and cross (Y-axis) directions.

Longitudinal Feed

The X-axis is moved by the handwheels shown in Figure 32 at the end of the table. These handwheels will move the table in both directions side-to-side. One complete revolution of either handwheel moves the longitudinal feed 0.100". There is also a scale on the front of the table for use when a tight tolerance is not required. The longitudinal feed can be locked in position by table locks located on the front of the table (see Figure 33).

Cross Feed

The Y-axis shown in Figure 32, is moved with the handwheel on the front of the table base. One complete revolution of the handwheel moves the cross slide 0.100". The cross feed can be locked into position by a table lock lever located on the right side of the cross slide underneath the table (see Figure 33).

X-Axis Handwheels

Y-Axis Handwheel

Figure 32. Table X- and Y-axis controls.

X-Axis Table Lock Levers

X-Axis Scale

Y-Axis Table Lock Levers

Figure 33. Table locks and scales.

-32-	Model G0704 (Mfg. Since 08/11)

Image 44

Contents Model G0759 Machine Data Sheet Table Info Column & Stand Description Electrical Box Headstock Description Chip Guard Labels Model G0704 MILL/DRILL with Stand Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification Electronic Controls Identification G0704 electronic controls identificationModel G0704 DRILL/MILL with Stand 50 2250 RPM Accessories Included Safety Safety Instructions for MachineryMaintain Power CORds. When disconnect ChILdREN & BYsTANdERs. KeepchildrenandAdditional Safety for Mill/Drills Power Supply Minimum Gauge Size 16 AWG 50 ftDescription Qty Needed for SetupUnpacking Not Shown Contents QtyInventory Basic steps for removing rust preventative CleanupBefore cleaning, gather the following Weight Load Site ConsiderationsExample of a direct mount setup Moving & Placing MachineMounting to Shop Floor Bolting to Concrete FloorsAssembly To install the drill chuck onto the arborDrill Chuck Arbor To assemble your machinePower Connection Connecting PowerTest Run & Spindle Break-in To test run and break-in the spindle bearingsOperations Operation OverviewBasic Controls Speed Range Selector Knob Selects low rangeDigital readout unit controls Model G0704 Mfg. Since 08/11 Digital Readout Unit To use the digital readoutCalculating Spindle Speed To determine the needed spindle speedSpindle Speed Direction To set the spindle speedChanging Spindle Position Using Quill Feed Levers Spindle Height ControlsTo install the drill chuck and arbor Drill ChuckTo remove the collet To install the toolingLoading Tooling To tilt the headstock to the left or right Headstock Travel Axis and RotationTo raise or lower the headstock Cross Feed Table TravelLongitudinal Feed G5684-R-8 Vertical Collet Rack H8179H8177-Worktable with Angle H5685-4Rotary Table G9322-Boring Head Combo SetG8683Z-Mini Shop Fox Mobile Base Model G9512 T-Slot Nuts G5758-Tilt xLubrication MaintenanceSchedule Tools Needed Qty To lubricate the leadscrewsHandwheel gears Service TroubleshootingSymptom Possible Cause Possible Solution Gibs To adjust the table gibsTo adjust the headstock gibs Battery Replacement To adjust the Y-axis leadscrew nutTo adjust the X-axis leadscrew To replace the digital readout unit batteryMotor Service To inspect and replace the motor brushesWiring Wiring Safety InstructionsWiring Diagram Rear panel Side panelParts Column BreakdownColumn Parts List Electrical Box Breakdown & Parts List 80-1 92V2Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List DescriptionLabels Breakdown & Parts List Model G0704 Mfg. Since 08/11 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns