Grizzly G0759 owner manual Digital Readout Unit, To use the digital readout

Page 37

Digital Readout Unit

The digital readout unit gives a precise reading of the vertical positioning of the quill. It can be zeroed at any position and manually increased or decreased independent of quill position when the operation requires it (Figure 23).

OFF Button

 

 

ON/0 Button

IN/MM Button

 

Button

 

Button

Battery Cover

 

Figure 23. Digital readout controls.

To use the digital readout:

1.Press the ON/0 button. A reading should appear on the display.

2.Press the IN/MM button to select whether units will be displayed in inches or millime- ters. Each press of the button switches from one unit to the other.

3.If you want to "zero" the readout at any time, press the ON/0 button. The current reading will be cleared and the scale will be reset to 0.000.

if you want to increase or decrease the read- ing at any time, press the appropriate or button. This is useful when calibrating the mill to known dimensions on a workpiece.

4.When the operation is complete, press the OFF button to conserve the battery.

Model G0704 (Mfg. Since 08/11)

-25-

Image 37
Contents Model G0759 Machine Data Sheet Table Info Column & Stand Description Electrical Box Headstock Description Chip Guard Labels Model G0704 MILL/DRILL with Stand Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description Identification G0704 electronic controls identification Electronic Controls IdentificationModel G0704 DRILL/MILL with Stand 50 2250 RPM Accessories Included Safety Instructions for Machinery SafetyChILdREN & BYsTANdERs. Keep­children­and­ Maintain Power CORds. When­ disconnectAdditional Safety for Mill/Drills Power Supply 50 ft Minimum Gauge Size 16 AWGUnpacking Needed for SetupDescription Qty Inventory Contents QtyNot Shown Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Weight LoadMoving & Placing Machine Example of a direct mount setupBolting to Concrete Floors Mounting to Shop FloorTo install the drill chuck onto the arbor AssemblyDrill Chuck Arbor To assemble your machineConnecting Power Power ConnectionTo test run and break-in the spindle bearings Test Run & Spindle Break-inOperation Overview OperationsSpeed Range Selector Knob Selects low range Basic ControlsDigital readout unit controls Model G0704 Mfg. Since 08/11 To use the digital readout Digital Readout UnitTo determine the needed spindle speed Calculating Spindle SpeedTo set the spindle speed Spindle Speed DirectionSpindle Height Controls Changing Spindle Position Using Quill Feed LeversDrill Chuck To install the drill chuck and arborLoading Tooling To install the toolingTo remove the collet To raise or lower the headstock Headstock Travel Axis and RotationTo tilt the headstock to the left or right Longitudinal Feed Table TravelCross Feed H8177-Worktable with Angle H8179G5684-R-8 Vertical Collet Rack G8683Z-Mini Shop Fox Mobile Base G9322-Boring Head Combo SetH5685-4Rotary Table G5758-Tilt x Model G9512 T-Slot NutsSchedule MaintenanceLubrication To lubricate the leadscrews Tools Needed QtyHandwheel gears Troubleshooting ServiceSymptom Possible Cause Possible Solution To adjust the headstock gibs To adjust the table gibsGibs To adjust the Y-axis leadscrew nut Battery ReplacementTo adjust the X-axis leadscrew To replace the digital readout unit batteryTo inspect and replace the motor brushes Motor ServiceWiring Safety Instructions WiringWiring Diagram Side panel Rear panelColumn Breakdown PartsColumn Parts List 80-1 92V2 Electrical Box Breakdown & Parts ListHeadstock Breakdown Headstock Parts List Description Chip Guard Breakdown & Parts ListLabels Breakdown & Parts List Model G0704 Mfg. Since 08/11 Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns