Grizzly G0759 ChILdREN & BYsTANdERs. Keep­children­and­, Maintain Power CORds. When­ disconnect

Page 21

­

WEARING PROPER APPAREL.­ Do­ not­ wear­ clothing,­ apparel­ or­ jewelry­ that­ can­ become­ entangled­ in­ moving­ parts.­ Always­ tie­ back­ or­ cover­ long­ hair.­ Wear­ non-slip­ footwear­ to­ avoid­ accidental­slips,­which­could­cause­loss­of­work- piece­control.

hAzARdOus dusT. Dust­ created­ while­ using­ machinery­ may­ cause­ cancer,­ birth­ defects,­ or­ long-term­ respiratory­ damage.­ Be­ aware­ of­ dust­ hazards­associated­with­each­workpiece­material,­ and­always­wear­a­NIOSH-approved­respirator­to­ reduce­your­risk.

hEARING PROTECTION.­ Always­ wear­ hear- ing­ protection­ when­ operating­ or­ observing­ loud­ machinery.­ Extended­ exposure­ to­ this­ noise­ without­ hearing­ protection­ can­ cause­ permanent­ hearing­loss.

REMOVE AdJusTING TOOLs.­ Tools­ left­ on­ machinery­ can­ become­ dangerous­ projectiles­ upon­startup.­Never­leave­chuck­keys,­wrenches,­ or­ any­ other­ tools­ on­ machine.­ Always­ verify­ removal­before­starting!

INTENdEd usAGE.­ Only­ use­ machine­ for­ its­ intended­purpose­and­never­make­modifications­ not­ approved­ by­ Grizzly.­ Modifying­ machine­ or­ using­ it­ differently­ than­ intended­ may­ result­ in­ malfunction­or­mechanical­failure­that­can­lead­to­ serious­personal­injury­or­death!

AWKWARd POsITIONs.­ Keep­ proper­ footing­ and­balance­at­all­times­when­operating­machine.­ Do­not­overreach!­Avoid­awkward­hand­positions­ that­ make­ workpiece­ control­ difficult­ or­ increase­ the­risk­of­accidental­injury.

ChILdREN & BYsTANdERs. Keep­children­and­

bystanders­at­a­safe­distance­from­the­work­area.

Stop­using­machine­if­they­become­a­distraction.

GuARds & COVERs.­Guards­and­covers­reduce­ accidental­ contact­ with­ moving­ parts­ or­ flying­ debris.­ Make­ sure­ they­ are­ properly­ installed,­ undamaged,­and­working­correctly.

FORCING MAChINERY.­Do­not­force­machine.­ It­ will­ do­ the­ job­ safer­ and­ better­ at­ the­ rate­ for­ which­it­was­designed.

NEVER sTANd ON MAChINE.­ Serious­ injury­ may­ occur­ if­ machine­ is­ tipped­ or­ if­ the­ cutting­ tool­is­unintentionally­contacted.­

sTABLE MAChINE. Unexpected­movement­dur- ing­ operation­ greatly­ increases­ risk­ of­ injury­ or­ loss­of­control.­Before­starting,­verify­machine­is­ stable­and­mobile­base­(if­used)­is­locked.

usE RECOMMENdEd ACCEssORIEs.­Consult­ this­owner’s­manual­or­the­manufacturer­for­rec- ommended­ accessories.­ Using­ improper­ acces- sories­will­increase­the­risk­of­serious­injury.

uNATTENdEd OPERATION. To­ reduce­ the­ risk­ of­ accidental­ injury,­ turn­ machine­ off­ and­ ensure­ all­ moving­ parts­ completely­ stop­ before­ walking­ away.­ Never­ leave­ machine­ running­ while­unattended.­

MAINTAIN WITh CARE.­Follow­all­maintenance­ instructions­ and­ lubrication­ schedules­ to­ keep­ machine­ in­ good­ working­ condition.­ A­ machine­ that­ is­ improperly­ maintained­ could­ malfunction,­ leading­to­serious­personal­injury­or­death.­

ChECK dAMAGEd PARTs.­ Regularly­ inspect­ machine­ for­ any­ condition­ that­ may­ affect­ safe­ operation.­Immediately­repair­or­replace­damaged­ or­mis-adjusted­parts­before­operating­machine.

MAINTAIN POWER CORds. When­ disconnect-

ing­ cord-connected­ machines­ from­ power,­ grab­ and­pull­the­plug—NOT­the­cord.­Pulling­the­cord­ may­ damage­ the­ wires­ inside.­ Do­ not­ handle­ cord/plug­with­wet­hands.­Avoid­cord­damage­by­ keeping­it­away­from­heated­surfaces,­high­traffic­ areas,­harsh­chemicals,­and­wet/damp­locations.

EXPERIENCING dIFFICuLTIEs. If­ at­ any­ time­ you­experience­difficulties­performing­the­intend- ed­operation,­stop­using­the­machine!­Contact­our­ Technical­Support­at­(570)­546-9663.

Model G0704 (Mfg. Since 08/11)

-9-

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model G0759 Machine Data Sheet Table Info Column & Stand Description Electrical Box Headstock Description Chip Guard Labels Model G0704 MILL/DRILL with Stand Page Table of Contents Introduction Manual Accuracy Contact InfoMachine Description Identification G0704 electronic controls identification Electronic Controls IdentificationModel G0704 DRILL/MILL with Stand 50 2250 RPM Accessories Included Safety Instructions for Machinery SafetyChILdREN & BYsTANdERs. Keep­children­and­ Maintain Power CORds. When­ disconnectAdditional Safety for Mill/Drills Power Supply 50 ft Minimum Gauge Size 16 AWGNeeded for Setup UnpackingDescription Qty Contents Qty InventoryNot Shown Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Weight LoadMoving & Placing Machine Example of a direct mount setupBolting to Concrete Floors Mounting to Shop FloorTo install the drill chuck onto the arbor AssemblyDrill Chuck Arbor To assemble your machineConnecting Power Power ConnectionTo test run and break-in the spindle bearings Test Run & Spindle Break-inOperation Overview OperationsSpeed Range Selector Knob Selects low range Basic ControlsDigital readout unit controls Model G0704 Mfg. Since 08/11 To use the digital readout Digital Readout UnitTo determine the needed spindle speed Calculating Spindle SpeedTo set the spindle speed Spindle Speed DirectionSpindle Height Controls Changing Spindle Position Using Quill Feed LeversDrill Chuck To install the drill chuck and arborTo install the tooling Loading ToolingTo remove the collet Headstock Travel Axis and Rotation To raise or lower the headstockTo tilt the headstock to the left or right Table Travel Longitudinal FeedCross Feed H8179 H8177-Worktable with AngleG5684-R-8 Vertical Collet Rack G9322-Boring Head Combo Set G8683Z-Mini Shop Fox Mobile BaseH5685-4Rotary Table G5758-Tilt x Model G9512 T-Slot NutsMaintenance ScheduleLubrication To lubricate the leadscrews Tools Needed QtyHandwheel gears Troubleshooting ServiceSymptom Possible Cause Possible Solution To adjust the table gibs To adjust the headstock gibsGibs To adjust the Y-axis leadscrew nut Battery ReplacementTo adjust the X-axis leadscrew To replace the digital readout unit batteryTo inspect and replace the motor brushes Motor ServiceWiring Safety Instructions WiringWiring Diagram Side panel Rear panelColumn Breakdown PartsColumn Parts List 80-1 92V2 Electrical Box Breakdown & Parts ListHeadstock Breakdown Headstock Parts List Description Chip Guard Breakdown & Parts ListLabels Breakdown & Parts List Model G0704 Mfg. Since 08/11 Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns
Top Page Image Contents