Grizzly G0759 owner manual Digital readout unit controls Model G0704 Mfg. Since 08/11

Page 36

Cross Handwheel: Moves the table forward and backward (Y-Axis).

Longitudinal Handwheels: Move the table from side to side (X-Axis).

Longitudinal Table Locks: Lock the longitudinal position of the table when tightened.

Cross Table Locks: Lock the cross position of the table when tightened.

Longitudinal

Longitudinal

Table Locks

Handwheels

Cross Handwheel

Cross Table Locks

Figure 20. Table controls.

Spindle RPM Readout: Displays the speed of the spindle rotation.

Emergency STOP Button: Interrupts the flow of power to the machine.

Variable Spindle Speed Knob: Changes the speed of the spindle rotation.

Spindle Direction Selection Knob: Changes the direction of spindle rotation.

Spindle RPM Readout

Emergency

STOP Button

Variable Spindle

Speed Knob

Spindle Direction

Selection Knob

Figure 21. Control panel.

-24-

OFF Button: Turns OFF the display.

ON/0 Button: Turns ON the display with the first press. Pressed again resets the display to 0.000".

IN/MM Button: Toggles the units displayed.

Button: Increases the current depth reading.

Button: Decreases the current depth reading.

OFF Button

ON/0 Button

IN/MM Button

Button

Button

Figure 22. Digital readout unit controls.

Model G0704 (Mfg. Since 08/11)

Image 36
Contents Model G0759 Machine Data Sheet Table Info Column & Stand Description Electrical Box Headstock Description Chip Guard Labels Model G0704 MILL/DRILL with Stand Page Table of Contents Introduction Manual Accuracy Contact InfoMachine Description Identification Electronic Controls Identification G0704 electronic controls identificationModel G0704 DRILL/MILL with Stand 50 2250 RPM Accessories Included Safety Safety Instructions for MachineryMaintain Power CORds. When­ disconnect ChILdREN & BYsTANdERs. Keep­children­and­Additional Safety for Mill/Drills Power Supply Minimum Gauge Size 16 AWG 50 ftNeeded for Setup UnpackingDescription Qty Contents Qty InventoryNot Shown Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Weight Load Site ConsiderationsExample of a direct mount setup Moving & Placing MachineMounting to Shop Floor Bolting to Concrete FloorsAssembly To install the drill chuck onto the arborDrill Chuck Arbor To assemble your machinePower Connection Connecting PowerTest Run & Spindle Break-in To test run and break-in the spindle bearingsOperations Operation OverviewBasic Controls Speed Range Selector Knob Selects low rangeDigital readout unit controls Model G0704 Mfg. Since 08/11 Digital Readout Unit To use the digital readoutCalculating Spindle Speed To determine the needed spindle speedSpindle Speed Direction To set the spindle speedChanging Spindle Position Using Quill Feed Levers Spindle Height ControlsTo install the drill chuck and arbor Drill ChuckTo install the tooling Loading ToolingTo remove the collet Headstock Travel Axis and Rotation To raise or lower the headstockTo tilt the headstock to the left or right Table Travel Longitudinal FeedCross Feed H8179 H8177-Worktable with AngleG5684-R-8 Vertical Collet Rack G9322-Boring Head Combo Set G8683Z-Mini Shop Fox Mobile BaseH5685-4Rotary Table Model G9512 T-Slot Nuts G5758-Tilt xMaintenance ScheduleLubrication Tools Needed Qty To lubricate the leadscrewsHandwheel gears Service TroubleshootingSymptom Possible Cause Possible Solution To adjust the table gibs To adjust the headstock gibsGibs Battery Replacement To adjust the Y-axis leadscrew nutTo adjust the X-axis leadscrew To replace the digital readout unit batteryMotor Service To inspect and replace the motor brushesWiring Wiring Safety InstructionsWiring Diagram Rear panel Side panelParts Column BreakdownColumn Parts List Electrical Box Breakdown & Parts List 80-1 92V2Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List DescriptionLabels Breakdown & Parts List Model G0704 Mfg. Since 08/11 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns