Grizzly G0759 owner manual Machine Data Sheet

Page 2

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0759 MILL/DRILL WITH STAND AND DRO

Product Dimensions:
Weight	280 lbs.
Width (side-to-side) x Depth (front-to-back) x Height	38 x 24 x 31 in.
Footprint (Length x Width)	15- 3/4 x 16-1/2 in.
Space Required for Full Range of Movement (Width x Depth)	57 x 25 in.
Shipping Dimensions:
Carton #1
Type	Wood Crate
Content	Machine
Weight	315 lbs.
Length x Width x Height	30 x 28 x 36 in.
Carton #2
Type	Cardboard Box
Content	Stand
Weight	77 lbs.
Length x Width x Height	17 x 17 x 33 in.
Electrical:
Power Requirement	110V, Single-Phase, 60 Hz
Prewired Voltage	110V
Full-Load Current Rating	12A
Minimum Circuit Size	15A
Connection Type	Cord & Plug
Power Cord Included	Yes
Power Cord Length	6 ft.
Power Cord Gauge	16 AWG
Plug Included	Yes
Included Plug Type	5-15
Switch Type	ON/OFF Push Button
Motors:
Main
Type	Universal
Horsepower	1 HP
Phase	Single-Phase
Amps	12A
Speed	4300 RPM
Power Transfer	Gear Drive
Bearings	Shielded & Permanently Lubricated

-2-	Model G0759 (Mfd. Since 1/14)

Image 2

Contents Model G0759 Machine Data Sheet Table Info Column & Stand Description Electrical Box Headstock Description Chip Guard Labels Model G0704 MILL/DRILL with Stand Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification Electronic Controls Identification G0704 electronic controls identificationModel G0704 DRILL/MILL with Stand 50 2250 RPM Accessories Included Safety Safety Instructions for MachineryMaintain Power CORds. When disconnect ChILdREN & BYsTANdERs. KeepchildrenandAdditional Safety for Mill/Drills Power Supply Minimum Gauge Size 16 AWG 50 ftDescription Qty Needed for SetupUnpacking Not Shown Contents QtyInventory Basic steps for removing rust preventative CleanupBefore cleaning, gather the following Weight Load Site ConsiderationsExample of a direct mount setup Moving & Placing MachineMounting to Shop Floor Bolting to Concrete FloorsDrill Chuck Arbor AssemblyTo install the drill chuck onto the arbor To assemble your machinePower Connection Connecting PowerTest Run & Spindle Break-in To test run and break-in the spindle bearingsOperations Operation OverviewBasic Controls Speed Range Selector Knob Selects low rangeDigital readout unit controls Model G0704 Mfg. Since 08/11 Digital Readout Unit To use the digital readoutCalculating Spindle Speed To determine the needed spindle speedSpindle Speed Direction To set the spindle speedChanging Spindle Position Using Quill Feed Levers Spindle Height ControlsTo install the drill chuck and arbor Drill ChuckTo remove the collet To install the toolingLoading Tooling To tilt the headstock to the left or right Headstock Travel Axis and RotationTo raise or lower the headstock Cross Feed Table TravelLongitudinal Feed G5684-R-8 Vertical Collet Rack H8179H8177-Worktable with Angle H5685-4Rotary Table G9322-Boring Head Combo SetG8683Z-Mini Shop Fox Mobile Base Model G9512 T-Slot Nuts G5758-Tilt xLubrication MaintenanceSchedule Tools Needed Qty To lubricate the leadscrewsHandwheel gears Service TroubleshootingSymptom Possible Cause Possible Solution Gibs To adjust the table gibsTo adjust the headstock gibs To adjust the X-axis leadscrew Battery ReplacementTo adjust the Y-axis leadscrew nut To replace the digital readout unit batteryMotor Service To inspect and replace the motor brushesWiring Wiring Safety InstructionsWiring Diagram Rear panel Side panelParts Column BreakdownColumn Parts List Electrical Box Breakdown & Parts List 80-1 92V2Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List DescriptionLabels Breakdown & Parts List Model G0704 Mfg. Since 08/11 Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns