Hitachi DV 24DV instruction manual Maintenance and Inspection

Page 23

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to turn off the switch and remove the battery before maintenance and inspection.

1.Inspecting the drill bits

Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is noted.

2.Inspecting the screws

Regularly inspect all screws and ensure that they are fully tightened. Should any of the screws be loosened, retighten them immediately.

WARNING: Using this drill with loosened screws is extremely dangerous.

3.Maintenance of the motor

The motor unit winding is the very “heart”’ of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.

4.Inspecting the carbon brushes (Fig. 15)

The motor employs carbon brushes which are consumable parts. Since and excessively worn carbon brush can result in motor trouble, replace the carbon brush with new ones when it becomes worn to or near the “wear limit”. In addition, always keep carbon brushes clean and ensure that they slide freely within the brush holders.

NOTE:

Wear limit

0.12" (3 mm)

0.45"

(11.5 mm)

Fig. 15

When replacing the carbon brush with a new one, be sure to use the Hitachi Carbon Brush Code No. 999058.

5.Replacing carbon brushes

Take out the carbon brush by first removing the brush cap and then hooking the protrusion of the carbon brush with a slotted-head screw driver, etc., as shown in Fig. 16, Fig. 17.

When installing the carbon brush, choose the direction so that the nail of the carbon brush (Fig. 16) agrees with the contact portion outside the brush tube (Fig. 18). Then push it in with a finger.

Lastly, install the brush cap.

Nail of carbon brush

Protrusion of carbon brush

Fig. 16

23

Image 23
Contents Variable speed AvertissementContents Meanings of Signal Words Important Safety InformationGeneral Safety Rules for ALL Battery Operated Tools SafetyEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Keep motor air vent cleanNever use a tool which is defective or operating abnormally Read ALL Instructions Important Safety Instructions for Battery ChargerEnglish Make Them Available to Other Users Owners of this Tool Cordless Hammer Drill DV24DV Functional DescriptionModel Name of PartsBattery Charger UC24YFB SpecificationsCapacity with Angle Unit Optional accessory Applications Assembly and OperationRemoval and Installation Method of Battery Insert the plug of battery charger into the receptacleCharging Insert the battery to the battery chargerRemove the battery from the battery charger Disconnect battery charger from the receptacleMounting and dismounting of the bit Before USEPrior to Operation Selecting the appropriate drill bit Installing the side handle and handle joint FigHigh-speed/Low-speed changeover Fig Hammer to Rotation changeover FigRemoving keyless chuck from hammer drill Fig Attaching the angle unit. Optional accessoryWhen using as a Drill or an Hammer Drill HOW to USESwitch operation English Maintenance and Inspection Check for Dust Disposal of the exhausted batteryService and repairs Service parts listModifications Battery EB2420 AccessoriesStandard Accessories Angle unit Code No Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéAvertissement Lire et coxmprendre toutes les instructions SecuriteConserver CES Instructions Avertissement NE Jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesNe pas essuyer les parties en plastique avec du solvant Garder propres les évents d’air du moteurLire Tout CE Mode D’EMPLOI Français Français Marteau perforateur à batterie DV24DV Description FonctionnelleModele NOM DES PartiesChargeur de batterie UC24YFB Capacité avec angle accessoire en option Retrait de la batterie Méthode DE Retrait ET D’INSTALLATION DE LA BatterieUtilisations Brancher la fiche du chargeur de batterie dans la priseRecharge Insérer la batterie dans le chargeur de batterieRetirer la batterie du chargeur de batterie PrecautionDébrancher le chargeur de batterie de la prise Pose et dépose du foret Avant L’UTILISATIONAvant LA Mise EN Marche Schéma vu du côté de la poignée Choix du foret de perçage correctMARTEAU/fonctionnement en Rota Installation de la poignée latérale et duJoint de poignée Fig Commutation fonctionnement enFixation de l’angle accessoire disponible en option Français La pièce à percer UtilisationFonctionnement de linterrupteur Entretien ET Inspection Entretien et réparation Vérifier s’il y a de la poussièreMise au rebut d’une batterie usée RangementListe des pièces de rechange Batterie EB2420 AccessoiresAccessoires Standard Unité de perçage dangle No. de code Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadAdvertencia Lea y entienda todas las instrucciones SeguridadGuarde Estas Instrucciones Advertencia Maneje correctamente la herramienta Normas Y Símbolos Específicos DE SeguridadUtilice la herramienta correcta No limpie las partes de plástico con disolvente Maneje con cuidado las herramientas eléctricasLEA Todas LAS Instrucciones Español Español Martillo roto-percutor a batería DV24DV Descripción FuncionalModelo NomenclaturaCargador de baterías UC24YFB EspecificacionesCapacidad con unidad angular accesorio opcional Método DE Carga Montaje Y OperaciónAplicaciones Método DE Extracción E Instalación DE LA BateríaRoja Inserte la batería en el cargador de bateríasPrecaución Desconecte el cargador de baterías del tomacorrienteExtraiga la batería del cargador de baterías Montaje y desmontaje de la broca Antes DE LA UtilizaciónAntes DE Usar LA Herramienta Instalación del asa lateral y de la unión del asa Fig Seleccionar la broca de taladro apropiadaCambio entre alta velocidad/baja velocidad Fig Cambio de Percusion a Rotacion FigFijación de la unidad angular Accesorio opcional Desmontaje del portabrocas de la unidad angular Uso como taladro común o taladro de percusión Como SE USAOperación del interruptor Mantenimiento E Inspección Mantenimiento y reparación Comprobación del polvoEliminación de las baterías agotadas AlmacenamientoModificaciones Lista de repuestosBattería EB2420 Accesorios EstándarBroca para concreto y ladrillo Unidad argulara Núm. de códigoUC24YFB Page Hitachi Koki Canada Co