Hitachi DV 24DV Important Safety Instructions for Battery Charger, Read ALL Instructions

Page 8
= 10 amperes

English

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER

WARNING: Death or serious bodily injury could result from improper or unsafe use of power tools. To avoid these risks, follow these basic safety instruc- tions:

READ ALL INSTRUCTIONS

1.This manual contains important safety and operating instructions for battery charger Model UC24YFB.

2.Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.

3.To reduce risk of injury, charge HITACHI rechargeable battery type EB2420. Other type of batteries may burst causing personal injury and damage.

4.Do not expose battery charger to rain or snow.

5.Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons.

6.To reduce risk of damage to electric plug and cord, pull by plug when disconnecting battery charger.

7.Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.

8.An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a.That blades of extension cord are the same number, size, and shape as those of plug on battery charger:

b.That extension cord is properly wired and in good electrical condition; and

c.That wire size is large enough for AC ampere rating of battery charger as specified

in Table 1.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes*

 

 

AWG Size of Cord

 

 

 

 

Equal to or

but less

 

Length of Cord, Feet (Meter)

 

greater than

than

25 (7.5)

50 (15)

100 (30)

150 (45)

0

2

18

18

18

16

2

3

18

18

16

14

3

4

18

18

16

14

*If the input rating of a battery charger is given in watts rather than in amperes, the corresponding ampere rating is to be determined by dividing the wattage rating by the voltage rating–for example:

1250watts

125 volts

8

Image 8
Contents Avertissement Variable speedContents Important Safety Information Meanings of Signal WordsSafety General Safety Rules for ALL Battery Operated ToolsEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Keep motor air vent cleanNever use a tool which is defective or operating abnormally Important Safety Instructions for Battery Charger Read ALL InstructionsEnglish Make Them Available to Other Users Owners of this Tool Functional Description ModelName of Parts Cordless Hammer Drill DV24DVSpecifications Battery Charger UC24YFBCapacity with Angle Unit Optional accessory Assembly and Operation Removal and Installation Method of BatteryInsert the plug of battery charger into the receptacle ApplicationsInsert the battery to the battery charger ChargingDisconnect battery charger from the receptacle Remove the battery from the battery chargerMounting and dismounting of the bit Before USEPrior to Operation Installing the side handle and handle joint Fig Selecting the appropriate drill bitHammer to Rotation changeover Fig High-speed/Low-speed changeover FigAttaching the angle unit. Optional accessory Removing keyless chuck from hammer drill FigWhen using as a Drill or an Hammer Drill HOW to USESwitch operation English Maintenance and Inspection Disposal of the exhausted battery Service and repairsService parts list Check for DustModifications Battery EB2420 AccessoriesStandard Accessories Angle unit Code No Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTAvertissement Lire et coxmprendre toutes les instructions SecuriteConserver CES Instructions Avertissement Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesGarder propres les évents d’air du moteur Ne pas essuyer les parties en plastique avec du solvantLire Tout CE Mode D’EMPLOI Français Français Description Fonctionnelle ModeleNOM DES Parties Marteau perforateur à batterie DV24DVChargeur de batterie UC24YFB Capacité avec angle accessoire en option Méthode DE Retrait ET D’INSTALLATION DE LA Batterie UtilisationsBrancher la fiche du chargeur de batterie dans la prise Retrait de la batterieInsérer la batterie dans le chargeur de batterie RechargeRetirer la batterie du chargeur de batterie PrecautionDébrancher le chargeur de batterie de la prise Pose et dépose du foret Avant L’UTILISATIONAvant LA Mise EN Marche Choix du foret de perçage correct Schéma vu du côté de la poignéeInstallation de la poignée latérale et du Joint de poignée FigCommutation fonctionnement en MARTEAU/fonctionnement en RotaFixation de l’angle accessoire disponible en option Français La pièce à percer UtilisationFonctionnement de linterrupteur Entretien ET Inspection Vérifier s’il y a de la poussière Mise au rebut d’une batterie uséeRangement Entretien et réparationListe des pièces de rechange Batterie EB2420 AccessoiresAccessoires Standard Unité de perçage dangle No. de code Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónAdvertencia Lea y entienda todas las instrucciones SeguridadGuarde Estas Instrucciones Advertencia Maneje correctamente la herramienta Normas Y Símbolos Específicos DE SeguridadUtilice la herramienta correcta Maneje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeLEA Todas LAS Instrucciones Español Español Descripción Funcional ModeloNomenclatura Martillo roto-percutor a batería DV24DVEspecificaciones Cargador de baterías UC24YFBCapacidad con unidad angular accesorio opcional Montaje Y Operación AplicacionesMétodo DE Extracción E Instalación DE LA Batería Método DE CargaInserte la batería en el cargador de baterías RojaPrecaución Desconecte el cargador de baterías del tomacorrienteExtraiga la batería del cargador de baterías Montaje y desmontaje de la broca Antes DE LA UtilizaciónAntes DE Usar LA Herramienta Seleccionar la broca de taladro apropiada Instalación del asa lateral y de la unión del asa FigCambio de Percusion a Rotacion Fig Cambio entre alta velocidad/baja velocidad FigFijación de la unidad angular Accesorio opcional Desmontaje del portabrocas de la unidad angular Uso como taladro común o taladro de percusión Como SE USAOperación del interruptor Mantenimiento E Inspección Comprobación del polvo Eliminación de las baterías agotadasAlmacenamiento Mantenimiento y reparaciónLista de repuestos ModificacionesAccesorios Estándar Battería EB2420Unidad argulara Núm. de código Broca para concreto y ladrilloUC24YFB Page Hitachi Koki Canada Co