Hitachi Koki USA W8VB2, W6B3, W6VA4, W6VM Assembly and Operation, Applications, Prior to Operation

Page 10

English

ASSEMBLY AND OPERATION

APPLICATIONS

Tightening hex. head screws

Tightening Drywall screws, wood screws and self-drilling screws

NOTE:

For tightening the Self-drilling screws, sub-stopper (B) and non-magnetic bit holder (sold separately) are recommended.

PRIOR TO OPERATION

1.Power source

Ensure that the power source to be utilized conforms to the power source re- quirements specified on the product nameplate.

2.Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a recep- tacle while the switch is in the ON position, the power tool will start operating immediately and can cause serious injury.

3.Extension cord

When the work area is far away from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.

WARNING:

Damaged cord must be replaced or repaired.

4.Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a seri- ous hazard.

5.Confirming condition of the environment

Confirm that the work site is placed under appropriate conditions conforming to prescribed precautions.

10

Image 10
Contents Advertencia AvertissementManual DE Instrucciones E Instrucciones DE Seguridad Contents Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Never operate without all guards in place Specific Safety Rules and SymbolsBlades and accessories must be securely mounted to the tool Use right toolDefinitions for symbols used on this tool. V ... volts Keep motor air vent cleanOperate power tools at the rated voltage Never use a tool which is defective or operating abnormallyMake Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationFunctional Description SpecificationsName of Parts Applications Assembly and OperationPrior to Operation Adjusting the tightening depth Fig Confirm the direction of bit rotation FigScrew Driver operation HOW to USE the Screw DriverMounting the bit Direction of hex-socket rotationDismounting the hex-socket Fig Mounting and Dismounting the HEX-SOCKET or the BITTightening Self-drilling screw Dismounting the bit FigMaintenance and Inspection Standard Accessories AccessoriesModifications For other screws For hex-head screwsPlastic case Code No Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTRegles Generale DE Securite SecuriteConserver CES Instructions Avertissement Lire et coxmprendre toutes les instructionsFrançais Regles DE Securite Specifiques ET Symboles Garder propres les évents d’air du moteur Utiliser l’outil correctManipuler l’outil correctement Utiliser l’outil motorisé à la tension nominaleManipuler l’outil motorisé avec précaution Ne pas essuyer les parties en plastique avec du solvantDouble Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties Description FonctionnelleRemarque Avant L’UTILISATION AvertissementRéglage de la profondeur de serrage Fig PrecautionVérifier la direction de la tête de vissage Pour vis autoperceuses à tête ronde FigFonctionnement de la visseuse Comment Utiliser LA VisseuseSens de rotation du manchon six pans Serrage d’une vis auto-foreuse Démontage du manchon six pans FigEntretien ET Inspection Accessoires Accessoires StandardPour les autres vis Pour vis à tête six pansBoîtier en plastique No. de code Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónNormas Generales DE Seguridad SeguridadGuarde Estas Instrucciones Advertencia Lea y entienda todas las instruccionesEspañol Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móviles Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Especificaciones Descripción FuncionalNomenclatura NotaAntes DE LA Operación Montaje Y OperaciónAplicaciones AdvertenciaAjustar la profundidad de apretado Fig Confirmar la dirección de rotación de la broca FigPrecaución Funcionamiento del destornillador Como Usar EL DestornilladorDirección de giro del portatornillos Inserción de tornillos autotaladradores Desmontaje de la broca Desmontaje del portatornillo hexagonalCuando montre el portatornillo hexagonal o la broca Mantenimiento E Inspección Accesorios Estándar AccesoriosModificaciones Para otros tornillos Para tornillos cabeza hexagonalCaja de plástico Num. de código THA,TPE,KOR 608VVMC2PS2L C D W6VA4 W6VB3 W8VB2 Page Page Page Hitachi Koki Canada Co