Hitachi Koki USA W6V4, W8VB2, W6B3, W6VA4, W6VM instruction manual Maintenance and Inspection

Page 14

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection.

1.Inspecting the hex. socket (or bit)

Since continued use of a worn hex. socket (bit) will damage screw heads, re- place the hex. socket (bit) with a new one as soon as excessive wear is noticed.

2.Inspecting the screws

Regularly inspect all screws and ensure that they are properly tightened. Should any of the screws be loosened, retighten them immediately.

WARNING: Using this screw driver with loosened screws is extremely dangerous.

3.Maintenance of the motor

The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.

4.Cleaning the unit exterior

Wipe off oil and stain on the unit exterior with a dried rag or a rag moistened with soapy water.

5.Inspecting the carbon brushes

For your continued safety and electrical shock protection, carbon brush inspec- tion and replacement on this tool should ONLY be performed by a Hitachi Authorized Service Center.

6.Service and repairs

All quality power tools will eventually require servicing or replacement of parts because of wear from normal use. To assure that only authorized replacement parts will be used, all service and repairs must be performed by a Hitachi Authorized Service Center, ONLY.

7.Service parts list

A:Item No.

B:Code No.

C:No. Used

D:Remarks

CAUTION: Repair, modification and inspection of Hitachi Power Tools must be

carried out by a Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

14

Image 14

Contents Manual DE Instrucciones E Instrucciones DE Seguridad AvertissementAdvertencia Contents Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Never operate without all guards in place Specific Safety Rules and SymbolsBlades and accessories must be securely mounted to the tool Use right toolDefinitions for symbols used on this tool. V ... volts Keep motor air vent cleanOperate power tools at the rated voltage Never use a tool which is defective or operating abnormallyMake Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationName of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Adjusting the tightening depth Fig Confirm the direction of bit rotation FigScrew Driver operation HOW to USE the Screw DriverMounting the bit Direction of hex-socket rotationDismounting the hex-socket Fig Mounting and Dismounting the HEX-SOCKET or the BITTightening Self-drilling screw Dismounting the bit FigMaintenance and Inspection Modifications AccessoriesStandard Accessories Plastic case Code No For hex-head screwsFor other screws Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTRegles Generale DE Securite SecuriteConserver CES Instructions Avertissement Lire et coxmprendre toutes les instructionsFrançais Regles DE Securite Specifiques ET Symboles Garder propres les évents d’air du moteur Utiliser l’outil correctManipuler l’outil correctement Utiliser l’outil motorisé à la tension nominaleManipuler l’outil motorisé avec précaution Ne pas essuyer les parties en plastique avec du solvantDouble Isolation Pour UN Fonctionnement Plus SUR Remarque Description FonctionnelleNOM DES Parties Avant L’UTILISATION AvertissementRéglage de la profondeur de serrage Fig PrecautionVérifier la direction de la tête de vissage Pour vis autoperceuses à tête ronde FigSens de rotation du manchon six pans Comment Utiliser LA VisseuseFonctionnement de la visseuse Serrage d’une vis auto-foreuse Démontage du manchon six pans FigEntretien ET Inspection Accessoires Accessoires StandardBoîtier en plastique No. de code Pour vis à tête six pansPour les autres vis Información Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónNormas Generales DE Seguridad SeguridadGuarde Estas Instrucciones Advertencia Lea y entienda todas las instruccionesEspañol Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móviles Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Especificaciones Descripción FuncionalNomenclatura NotaAntes DE LA Operación Montaje Y OperaciónAplicaciones AdvertenciaPrecaución Confirmar la dirección de rotación de la broca FigAjustar la profundidad de apretado Fig Dirección de giro del portatornillos Como Usar EL DestornilladorFuncionamiento del destornillador Inserción de tornillos autotaladradores Cuando montre el portatornillo hexagonal o la broca Desmontaje del portatornillo hexagonalDesmontaje de la broca Mantenimiento E Inspección Modificaciones AccesoriosAccesorios Estándar Caja de plástico Num. de código Para tornillos cabeza hexagonalPara otros tornillos THA,TPE,KOR 608VVMC2PS2L C D W6VA4 W6VB3 W8VB2 Page Page Page Hitachi Koki Canada Co