Hitachi B13F Drill Press Adjustments, Tilting the Table Fig. H, Spindle / Quill Fig

Page 13

DRILL PRESS ADJUSTMENTS

CAUTION: All the adjustments for the operation of the drill press have been completed at the factory. Due to normal wear and use, some occasional readjustments may be necessary.

WARNING

To prevent personal injury, always disconnect the plug from the power source when making any adjustment.

TILTING THE TABLE (Fig. H)

NOTE: The bevel scale has been included to measure approximate bevel angles. if precision is necessary, a square or other measuring tool should be used to position the table. To use the bevel scale (1):

1.Remove pin and nut (2). Tighten nut until pin slips out.

2.Loosen the large hex head bevel locking bolt (3).

Fig. H

1

3

2

WARNING

To prevent injury, be sure to hold the table assembly, so it will not swivel or tilt.

3.Tilt the table, aligning the desired angle measurement to the zero line scribed on the table opposite the bevel scale (1).

4.Tighten the bevel locking bolt (3).

5.To return the table to its original position, loosen the bevel locking bolt (3). Realign the bevel scale (1) to the 0 scribed line on the table.

6.Back nut out several turns, reinsert pin and nut into table, and tap into place with hammer.

7.Tighten the bevel locking bolt.

NOTE: The table has been removed from the illustration for clarity.

WARNING

To prevent personal injury, always disconnect the plug from the power source when making any adjustment.

English

SPINDLE / QUILL (Fig. I)

Rotate the feed handles counterclockwise to lower spindle to its lowest position. Hand support the spindle securely and move it back and forth around the axis. If there is play, do the following:

1.Loosen the lock nut (1).

2.Turn the screw (2) clockwise to eliminate the play, but without obstructing the upward movement of the spindle.

3.Tighten the lock nut (1).

Fig. I

1

2

WARNING

To prevent personal injury, always disconnect the plug from the power source when making any adjustment.

QUILL RETURN SPRING (Fig. J)

The quill return spring may need adjustment if the tension causes the quill to return too rapidly or too slowly.

1.Lower the table for additional clearance.

2.Place a screwdriver in the lower front notch (1) of the spring cap (2). Hold it in place while loosening and removing only the outer jam nut (3).

3.With the screwdriver still engaged in the notch loosen the

inner nut (4) just until the notch (5) disengages from the boss (6) on the drill press head.

CAUTION: DO NOT REMOVE THIS INNER NUT, because the spring will forcibly unwind.

Fig. J

6

5

4

3

2

1

4.Carefully turn the spring cap (2) counterclockwise with the screwdriver, engaging the next notch.

5.Lower the quill to the lowest position by rotating the feed handle in a counterclockwise direction while holding the spring cap (2) in position.

– 13 –

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Hitachi Hitachi Authorized Service Centers NET Weight Product SpecificationsMotor 61 LB 27.5 kgGeneral Safety Instructions SafetyBefore Using the Drill Press Specific Safety Instructions for the Drill Press Guidelines for Extension Cords Electrical RequirementsCarton Contents Accessories and AttachmentsUnpacking Your Drill Press Know Your Drill Press Drill Press Terms Glossary of TermsDepth Scale Stop Nuts Lock the spindle to a Assembly Instructions Assembly and AdjustmentsEstimated Assembly Time 20-40 Minutes Tools NeededInstalling the Head Fig. D Installing Battery for Laser Guide Fig. C-1Installing Feed Handles Fig. E Installing the Chuck Fig. F and GTilting the Table Fig. H Drill Press AdjustmentsSpindle / Quill Fig Quill Return Spring Fig. JBelt Tension Fig. K Avoid Direct EYE ContactLaser Guide Basic Drill Press Operations OperationYour Protection Basic Operation IstructionsDrilling to a Specific Depth Fig. P Removing Chuck and Arbor Fig. RFeeding Positioning the Table and Workpiece Fig. S and TMaintaining Your Drill Press MaintenanceLubrication BatteriesProblem Probable Cause Remedy Troubleshooting GuideGeneral Moteur Spécifications DU ProduitPoids NET 27,5 kg 61 lbConsignes DE Sécurité Générales SécuritéAvant D’UTILISER Cette Perceuse Consignes DE Sécurité Spécifiques À LA Perceuse D’ÉTABLI Directives Pour LES Rallonges Électriques Exigences ÉlectriquesCalibre Minimal Pour Cordons Prolongateurs AWG Avec du 120 V seulementAccessoires Recommandés Accessoires ET ÉquipementsContenu DU Carton Déballage ET Vérification DU ContenuDéballage DE LA Perceuse MARCHE/ARRÊT Connaître SA PerceuseBoutons DE Verrouillage DE Tension DE Glossaire DES TermesÉcrous DE Blocage D’ÉCHELLE DE Interrupteur DE MARCHE/ARRÊT DEInstructions D’ASSEMBLAGE Assemblage ET AjustementsTemps D’ASSEMBLAGE Prévu 35 Minutes Outils RequisInstallation DU Mandrin Fig. F et G Installation DE LA Tête Fig. DInsertion DES Piles Dans LE Guide AU Laser Fig. C-1 Nstallation DES Leviers DE Manoeuvre Fig. EInclinaison DE LA Table Fig. H Réglages DE LA PerceuseBroche / Arbre Creux Fig Ressort DE Rappel DE L’ARBRE Creux Fig. JTension DE LA Courroie Fig. K Éviter UN Contact Direct Avec LES YeuxLE Guide Laser Opérations DE Base DE LA Perceuse FonctionnementVotre Protection Instructions SUR LE Fonctionnement DE BasePerçage À UNE Profondeur Spécifique Fig. P Dépose DU Mandrin ET DE L’ARBRE Fig. RDiam Matériau Du foret Bois Tableau DES Vitesses DE PerçagePlastique Acier Inox DouxEntretien DE LA Perceuse EntretienPositionnement LubrificationProblème Causes Probable Action Corrective Guide DE DépannageMotor Especificaciones DEL ProductoAmperios Peso NetoInstrucciones Generales DE Seguridad SeguridadAntes DE Usar Esta Prensa Taladradora Especificaciones DE LA Alimentacion Electrica Y EL Motor Requisitos ElectricosInstrucciones Para LA Conexion a Tierra Pautas Para EL USO DE Cables DE ExtensionEN Caso DE UN MAL Funcionamiento O UNA Calibre Minimo Para Cables DE Extension AWGContenido DE LA Caja Accesorios Y AditamentosAccesorios Recomendados Desempaque Y Verificacion DEL ContenidoDesempaque DE Prensa Taladradora Conozca SU Prensa Taladradora Manillas DE Fijacion DE LA Tension DE LA Correa Glosario DE TerminosTuercas DE Tope DE LA Escala DE Profundidad Interruptor DE Encendido Y Apagado DEL TaladroInstruccioned DE Montaje Montaje Y AjustesHerramientas Necesarias Instalacion DEL Cabezal Fig. D Instalacion DE LA Bateria Para LA Guia Laser Fig. C-1Instalacion DE LOS Mangos DE Alimentacion Fig. E Instalacion DEL Portabrocas Fig. F y GInclinacion DE LA Mesa Fig. H Ajustes DE LA Prensa TaladradoraHusillo / Manguito Fig Resorte DE Retorno DEL Manguito Fig. JLA Guia Laser Tension DE LA Correa Fig. KEvite EL Contacto Directo CON LOS Ojos Operaciones Basicas DE LA Prensa Taladradora OperacionSU Proteccion Instrucciones Basicas DE OperacionTaladrado a UNA Profundidad Especifica Fig. P Desmontaje DEL Portabrocas Y EL Arbol Fig. RDiám Material De broca Madera Tabla DE Velocidad DE Taladradora RPMPlástico Acero Inoxid Pulg Dulce Colocacion DE LA Mesa Y DE LA Pieza DE Trabajo Fig. S y TDele Mantenimiento a SU Prensa Taladradora MantenimientoAlimentacion LubricacionProblema Causa Probable Solucion Guia DE Identificacion DE ProblemasGeneralidades 10 ″ Bench Drill Press Schematic aModel NO. B13F 10″ Bench Drill Press Model NO. B13F Parts List for Schematic aAlways Order by Part NO. and I.D. Number Hitachi Koki Canada Co

B13F specifications

The Hitachi B13F is a versatile and robust benchtop drill press designed to meet the demands of both professionals and hobbyists in various applications. Known for its reliability and precision, the B13F combines advanced technology with practical features that make it a popular choice among woodworkers, metalworkers, and those involved in DIY projects.

One of the standout features of the Hitachi B13F is its powerful 350-watt motor, which provides sufficient torque for a wide range of drilling operations. This motor is designed to handle heavier materials, ensuring that users can work with wood, metal, and plastics without compromising on performance. Additionally, the drill press offers a variable speed control system, allowing users to select from a speed range of 580 to 3,050 RPM, making it suitable for drilling different materials with ease and precision.

The B13F's 13mm keyless chuck provides convenience and quick tool changes, reducing setup time and enhancing productivity. This feature allows users to effortlessly switch between drill bits without the need for additional tools, which is especially beneficial for those who require frequent bit changes on the job site or in their workshops.

Precision is a hallmark of the Hitachi B13F, thanks in part to its laser guide system that aids in aligning the drill bit with the target material. This ensures accurate and clean holes, minimizing the risk of error in drilling. The drill press is equipped with an adjustable depth stop, enabling users to set the maximum drilling depth for consistent results across multiple holes.

The construction of the B13F is another highlight, with a sturdy cast iron base that provides stability during operation. This solid foundation minimizes vibrations, contributing to a smoother drilling experience and enhancing the overall accuracy of the tool. The height-adjustable work table also adds flexibility, allowing users to accommodate various workpiece sizes effortlessly.

Moreover, safety features such as the emergency stop switch and a built-in work light further enhance the usability of the Hitachi B13F, ensuring that operators can work efficiently while prioritizing safety.

In summary, the Hitachi B13F benchtop drill press combines power, precision, and convenience in a compact design. With advanced technologies such as variable speed control, a keyless chuck, and laser guiding capabilities, it stands out as a reliable tool for a wide range of drilling tasks, making it an excellent investment for both professional workshops and home garages.
Top Page Image Contents