Hitachi B13F instruction manual Troubleshooting Guide, General, Problem Probable Cause Remedy

Page 19

English

TROUBLESHOOTING GUIDE

WARNING

•To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source before making any adjustments.

•All electrical or mechanical repairs should be done only by qualified service technicians. Contact Hitachi Authorized Service Center.

GENERAL

 

PROBLEM

PROBABLE CAUSE

REMEDY

 

Noisy operation

1.

Incorrect belt tension.

1.

Adjust tension. See DRILL PRESS

 

 

 

 

 

ADJUSTMENTS section, BELT TENSION.

 

 

2.

Loose spindle pulley.

2.

Check tighteness of retaining nut on pulley, and

 

 

 

 

 

tighten if necessary

 

 

3.

Loose motor pulley

3.

Tighten set screw in motor pulley.

 

 

 

 

 

 

 

Drill bit burns.

1.

Incorrect speed.

1.

Change speed. See BASIC DRILL PRESS

 

 

 

 

 

OPERATIONS section, SPEEDS AND BELT

 

 

 

 

 

PLACEMENT.

 

 

2.

Chips not coming out of hole.

2.

Retract drill frequently to clear chips.

 

 

3.

Dull drill bit.

3.

Resharpen drill bit.

 

 

 

 

 

 

 

 

Run out of drill bit point - drill

1.

Hand grain in wood or lengths of cutting

1.

Resharpen drill bit correctly.

 

hole not round.

 

flutes and/or angles not equal.

 

 

 

 

 

2.

Bent drill bit..

2.

Replace drill bit.

 

Wood splinters on underside.

1.

No backup material under workpiece.

1.

Use backup material. See BASIC DRILL PRESS

 

 

 

 

 

OPERATIONS section.

 

Workpice torn loose from hand.

1.

Not supported or clamped properly.

1.

Support workpiece or clamp it. See BASIC DRILL

 

 

 

 

 

PRESS OPERATIONS section.

 

Drill bit binds in workpiece.

1.

Workpiece pinching drill bit, or excessive

1.

Support workpiece or clamp it. See BASIC DRILL

 

 

 

feed pressure.

 

PRESS OPERATIONS section.

 

 

2.

Improper belt tension.

2.

Adjust tension. See DRILL PRESS

 

 

 

 

 

ADJUSTMENTS section, BELT TENSION.

 

 

Excessive drill bit runout or

1.

Bent drill bit.

1.

Replace drill bit.

 

wobble.

2.

Worn bearings.

2.

Replace bearings.

 

 

3.

Drill bit not properly installed in chuck.

3.

Install drill properly. See BASIC DRILL PRESS

 

 

 

 

 

OPERATIONS section, INSTALLING DRILL BIT.

 

 

4.

Chuck not properly installed.

4.

Install chuck properly. See ASSEMBLY

 

 

 

 

 

INSTRUCTIONS section, INSTALLING THE

 

 

 

 

 

CHUCK.

 

 

 

 

 

 

 

Quill returns too slow or too

1.

Spring has improper tension.

1.

Adjust spring tension. See ASSEMBLY

 

 

fast.

 

 

 

INSTRUCTIONS section, QUILL RETURN

 

 

 

 

 

SPRING.

 

 

 

 

 

 

 

Chuck will not stay attached to

1.

Dirt, grease, or oil on the tapered inside

1.

Using a household detergent, clean the tapered

 

spindle. It falls off when trying

 

surface of chuck or on the spindle’s

 

surface of the chuck and spindle to remove all dirt,

 

to install.

 

tapered surface.

 

grease and oil. See ASSEMBLY INSTRUCTIONS

 

 

 

 

 

section, INSTALLING THE CHUCK.

 

The LASER GUIDE will not

1.

The batteries have become uncharged.

1.

See ASSEMBLY INSTRUCTIONS section,

 

turn on.

 

 

 

INSTALLING BATTERY FOR LASER GUIDE.

 

 

 

 

 

 

 

– 19 –

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Hitachi Hitachi Authorized Service Centers 61 LB 27.5 kg Product SpecificationsNET Weight MotorGeneral Safety Instructions SafetyBefore Using the Drill Press Specific Safety Instructions for the Drill Press Guidelines for Extension Cords Electrical RequirementsCarton Contents Accessories and AttachmentsUnpacking Your Drill Press Know Your Drill Press Drill Press Terms Glossary of TermsDepth Scale Stop Nuts Lock the spindle to a Tools Needed Assembly and AdjustmentsAssembly Instructions Estimated Assembly Time 20-40 MinutesInstalling the Chuck Fig. F and G Installing Battery for Laser Guide Fig. C-1Installing the Head Fig. D Installing Feed Handles Fig. EQuill Return Spring Fig. J Drill Press AdjustmentsTilting the Table Fig. H Spindle / Quill FigBelt Tension Fig. K Avoid Direct EYE ContactLaser Guide Basic Drill Press Operations OperationRemoving Chuck and Arbor Fig. R Basic Operation IstructionsYour Protection Drilling to a Specific Depth Fig. PFeeding Positioning the Table and Workpiece Fig. S and TBatteries MaintenanceMaintaining Your Drill Press LubricationProblem Probable Cause Remedy Troubleshooting GuideGeneral 27,5 kg 61 lb Spécifications DU ProduitMoteur Poids NETConsignes DE Sécurité Générales SécuritéAvant D’UTILISER Cette Perceuse Consignes DE Sécurité Spécifiques À LA Perceuse D’ÉTABLI AWG Avec du 120 V seulement Exigences ÉlectriquesDirectives Pour LES Rallonges Électriques Calibre Minimal Pour Cordons ProlongateursDéballage ET Vérification DU Contenu Accessoires ET ÉquipementsAccessoires Recommandés Contenu DU CartonDéballage DE LA Perceuse MARCHE/ARRÊT Connaître SA PerceuseInterrupteur DE MARCHE/ARRÊT DE Glossaire DES TermesBoutons DE Verrouillage DE Tension DE Écrous DE Blocage D’ÉCHELLE DEOutils Requis Assemblage ET AjustementsInstructions D’ASSEMBLAGE Temps D’ASSEMBLAGE Prévu 35 MinutesNstallation DES Leviers DE Manoeuvre Fig. E Installation DE LA Tête Fig. DInstallation DU Mandrin Fig. F et G Insertion DES Piles Dans LE Guide AU Laser Fig. C-1Ressort DE Rappel DE L’ARBRE Creux Fig. J Réglages DE LA PerceuseInclinaison DE LA Table Fig. H Broche / Arbre Creux FigTension DE LA Courroie Fig. K Éviter UN Contact Direct Avec LES YeuxLE Guide Laser Opérations DE Base DE LA Perceuse FonctionnementDépose DU Mandrin ET DE L’ARBRE Fig. R Instructions SUR LE Fonctionnement DE BaseVotre Protection Perçage À UNE Profondeur Spécifique Fig. PDoux Tableau DES Vitesses DE PerçageDiam Matériau Du foret Bois Plastique Acier InoxLubrification EntretienEntretien DE LA Perceuse PositionnementProblème Causes Probable Action Corrective Guide DE DépannagePeso Neto Especificaciones DEL ProductoMotor AmperiosInstrucciones Generales DE Seguridad SeguridadAntes DE Usar Esta Prensa Taladradora Especificaciones DE LA Alimentacion Electrica Y EL Motor Requisitos ElectricosCalibre Minimo Para Cables DE Extension AWG Pautas Para EL USO DE Cables DE ExtensionInstrucciones Para LA Conexion a Tierra EN Caso DE UN MAL Funcionamiento O UNADesempaque Y Verificacion DEL Contenido Accesorios Y AditamentosContenido DE LA Caja Accesorios RecomendadosDesempaque DE Prensa Taladradora Conozca SU Prensa Taladradora Interruptor DE Encendido Y Apagado DEL Taladro Glosario DE TerminosManillas DE Fijacion DE LA Tension DE LA Correa Tuercas DE Tope DE LA Escala DE ProfundidadInstruccioned DE Montaje Montaje Y AjustesHerramientas Necesarias Instalacion DEL Portabrocas Fig. F y G Instalacion DE LA Bateria Para LA Guia Laser Fig. C-1Instalacion DEL Cabezal Fig. D Instalacion DE LOS Mangos DE Alimentacion Fig. EResorte DE Retorno DEL Manguito Fig. J Ajustes DE LA Prensa TaladradoraInclinacion DE LA Mesa Fig. H Husillo / Manguito FigLA Guia Laser Tension DE LA Correa Fig. KEvite EL Contacto Directo CON LOS Ojos Operaciones Basicas DE LA Prensa Taladradora OperacionDesmontaje DEL Portabrocas Y EL Arbol Fig. R Instrucciones Basicas DE OperacionSU Proteccion Taladrado a UNA Profundidad Especifica Fig. PColocacion DE LA Mesa Y DE LA Pieza DE Trabajo Fig. S y T Tabla DE Velocidad DE Taladradora RPMDiám Material De broca Madera Plástico Acero Inoxid Pulg DulceLubricacion MantenimientoDele Mantenimiento a SU Prensa Taladradora AlimentacionProblema Causa Probable Solucion Guia DE Identificacion DE ProblemasGeneralidades 10 ″ Bench Drill Press Schematic aModel NO. B13F 10″ Bench Drill Press Model NO. B13F Parts List for Schematic aAlways Order by Part NO. and I.D. Number Hitachi Koki Canada Co

B13F specifications

The Hitachi B13F is a versatile and robust benchtop drill press designed to meet the demands of both professionals and hobbyists in various applications. Known for its reliability and precision, the B13F combines advanced technology with practical features that make it a popular choice among woodworkers, metalworkers, and those involved in DIY projects.

One of the standout features of the Hitachi B13F is its powerful 350-watt motor, which provides sufficient torque for a wide range of drilling operations. This motor is designed to handle heavier materials, ensuring that users can work with wood, metal, and plastics without compromising on performance. Additionally, the drill press offers a variable speed control system, allowing users to select from a speed range of 580 to 3,050 RPM, making it suitable for drilling different materials with ease and precision.

The B13F's 13mm keyless chuck provides convenience and quick tool changes, reducing setup time and enhancing productivity. This feature allows users to effortlessly switch between drill bits without the need for additional tools, which is especially beneficial for those who require frequent bit changes on the job site or in their workshops.

Precision is a hallmark of the Hitachi B13F, thanks in part to its laser guide system that aids in aligning the drill bit with the target material. This ensures accurate and clean holes, minimizing the risk of error in drilling. The drill press is equipped with an adjustable depth stop, enabling users to set the maximum drilling depth for consistent results across multiple holes.

The construction of the B13F is another highlight, with a sturdy cast iron base that provides stability during operation. This solid foundation minimizes vibrations, contributing to a smoother drilling experience and enhancing the overall accuracy of the tool. The height-adjustable work table also adds flexibility, allowing users to accommodate various workpiece sizes effortlessly.

Moreover, safety features such as the emergency stop switch and a built-in work light further enhance the usability of the Hitachi B13F, ensuring that operators can work efficiently while prioritizing safety.

In summary, the Hitachi B13F benchtop drill press combines power, precision, and convenience in a compact design. With advanced technologies such as variable speed control, a keyless chuck, and laser guiding capabilities, it stands out as a reliable tool for a wide range of drilling tasks, making it an excellent investment for both professional workshops and home garages.
Top Page Image Contents