Hitachi B13F instruction manual General Safety Instructions, Before Using the Drill Press

Page 4

English

SAFETY

GENERAL SAFETY INSTRUCTIONS

BEFORE USING THE DRILL PRESS

Safety is a combination of common sense, staying alert and knowing how to use this Drill Press.

WARNING

To avoid mistakes that could cause serious injury, do not plug the Drill Press in until you have read and understood the following:

1.READ and become familiar with the entire Operator’s Manual. LEARN the tool’s application, limitations and possible hazards.

2.KEEP GUARDS IN PLACE and in working order.

3.REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to see that keys and adjusting wrenches are removed from the tool before turning ON.

4.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

5.DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them to rain. Keep work area well lighted.

6.KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from work area.

7.MAKE WORKSHOP CHILDPROOF with padlocks, master switches, or by removing starter keys.

8.DON’T FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed.

9.USE THE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed.

10.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will result in a drop in line voltage and in loss of power that will cause the tool to overheat. The table on page 6 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

11.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.

12.ALWAYS WEAR EYE PROTECTION. Any Drill Press can throw foreign objects into the eyes that could cause permanent eye damage. ALWAYS wear Safety Goggles (not glasses) that comply with ANSI Safety Standard Z87.1. Everyday eyeglasses have only impact-resistance lenses. They ARE NOT safety glasses. Safety Goggles are available at HITACHI.

NOTE: Glasses or goggles not in compliance with ANSI Z87.1 could cause serious injury.

13.SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and it frees both hands to operate tool.

14.DISCONNECT TOOLS before servicing; when changing accessories such as blades, bits, cutters, and the like.

15.REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in OFF position before plugging in.

16.USE RECOMMENDED ACCESSORIES. Consult the Operator’s Manual for recommended accessories. The use of improper accessories may cause serious injury.

17.NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

18.CHECK FOR DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function – check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

19.NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER “OFF”. Don’t leave tool until it comes to a complete stop.

20.DON’T OVERREACH. Keep proper footing and balance at all times.

21.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

22.DO NOT use power tools in the presence of flammable liquids or gases.

23.DO NOT OPERATE the tool if you are under the influence of any drugs, alcohol or medication that could affect your ability to use the tool properly.

24.ALWAYS operate the Drill Press in a well-ventilated area and provide for proper dust removal. Use dust collection systems whenever possible. Dust generated from certain materials can be hazardous to your health.

– 4 –

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Hitachi Hitachi Authorized Service Centers Product Specifications NET WeightMotor 61 LB 27.5 kgGeneral Safety Instructions SafetyBefore Using the Drill Press Specific Safety Instructions for the Drill Press Electrical Requirements Guidelines for Extension CordsAccessories and Attachments Carton ContentsUnpacking Your Drill Press Know Your Drill Press Drill Press Terms Glossary of TermsDepth Scale Stop Nuts Lock the spindle to a Assembly and Adjustments Assembly InstructionsEstimated Assembly Time 20-40 Minutes Tools NeededInstalling Battery for Laser Guide Fig. C-1 Installing the Head Fig. DInstalling Feed Handles Fig. E Installing the Chuck Fig. F and GDrill Press Adjustments Tilting the Table Fig. HSpindle / Quill Fig Quill Return Spring Fig. JBelt Tension Fig. K Avoid Direct EYE ContactLaser Guide Operation Basic Drill Press OperationsBasic Operation Istructions Your ProtectionDrilling to a Specific Depth Fig. P Removing Chuck and Arbor Fig. RPositioning the Table and Workpiece Fig. S and T FeedingMaintenance Maintaining Your Drill PressLubrication BatteriesProblem Probable Cause Remedy Troubleshooting GuideGeneral Spécifications DU Produit MoteurPoids NET 27,5 kg 61 lbConsignes DE Sécurité Générales SécuritéAvant D’UTILISER Cette Perceuse Consignes DE Sécurité Spécifiques À LA Perceuse D’ÉTABLI Exigences Électriques Directives Pour LES Rallonges ÉlectriquesCalibre Minimal Pour Cordons Prolongateurs AWG Avec du 120 V seulementAccessoires ET Équipements Accessoires RecommandésContenu DU Carton Déballage ET Vérification DU ContenuDéballage DE LA Perceuse Connaître SA Perceuse MARCHE/ARRÊTGlossaire DES Termes Boutons DE Verrouillage DE Tension DEÉcrous DE Blocage D’ÉCHELLE DE Interrupteur DE MARCHE/ARRÊT DEAssemblage ET Ajustements Instructions D’ASSEMBLAGETemps D’ASSEMBLAGE Prévu 35 Minutes Outils RequisInstallation DE LA Tête Fig. D Installation DU Mandrin Fig. F et GInsertion DES Piles Dans LE Guide AU Laser Fig. C-1 Nstallation DES Leviers DE Manoeuvre Fig. ERéglages DE LA Perceuse Inclinaison DE LA Table Fig. HBroche / Arbre Creux Fig Ressort DE Rappel DE L’ARBRE Creux Fig. JTension DE LA Courroie Fig. K Éviter UN Contact Direct Avec LES YeuxLE Guide Laser Fonctionnement Opérations DE Base DE LA PerceuseInstructions SUR LE Fonctionnement DE Base Votre ProtectionPerçage À UNE Profondeur Spécifique Fig. P Dépose DU Mandrin ET DE L’ARBRE Fig. RTableau DES Vitesses DE Perçage Diam Matériau Du foret BoisPlastique Acier Inox DouxEntretien Entretien DE LA PerceusePositionnement LubrificationGuide DE Dépannage Problème Causes Probable Action CorrectiveEspecificaciones DEL Producto MotorAmperios Peso NetoInstrucciones Generales DE Seguridad SeguridadAntes DE Usar Esta Prensa Taladradora Requisitos Electricos Especificaciones DE LA Alimentacion Electrica Y EL MotorPautas Para EL USO DE Cables DE Extension Instrucciones Para LA Conexion a TierraEN Caso DE UN MAL Funcionamiento O UNA Calibre Minimo Para Cables DE Extension AWGAccesorios Y Aditamentos Contenido DE LA CajaAccesorios Recomendados Desempaque Y Verificacion DEL ContenidoDesempaque DE Prensa Taladradora Conozca SU Prensa Taladradora Glosario DE Terminos Manillas DE Fijacion DE LA Tension DE LA CorreaTuercas DE Tope DE LA Escala DE Profundidad Interruptor DE Encendido Y Apagado DEL TaladroInstruccioned DE Montaje Montaje Y AjustesHerramientas Necesarias Instalacion DE LA Bateria Para LA Guia Laser Fig. C-1 Instalacion DEL Cabezal Fig. DInstalacion DE LOS Mangos DE Alimentacion Fig. E Instalacion DEL Portabrocas Fig. F y GAjustes DE LA Prensa Taladradora Inclinacion DE LA Mesa Fig. HHusillo / Manguito Fig Resorte DE Retorno DEL Manguito Fig. JLA Guia Laser Tension DE LA Correa Fig. KEvite EL Contacto Directo CON LOS Ojos Operacion Operaciones Basicas DE LA Prensa TaladradoraInstrucciones Basicas DE Operacion SU ProteccionTaladrado a UNA Profundidad Especifica Fig. P Desmontaje DEL Portabrocas Y EL Arbol Fig. RTabla DE Velocidad DE Taladradora RPM Diám Material De broca MaderaPlástico Acero Inoxid Pulg Dulce Colocacion DE LA Mesa Y DE LA Pieza DE Trabajo Fig. S y TMantenimiento Dele Mantenimiento a SU Prensa TaladradoraAlimentacion LubricacionProblema Causa Probable Solucion Guia DE Identificacion DE ProblemasGeneralidades 10 ″ Bench Drill Press Schematic aModel NO. B13F 10″ Bench Drill Press Model NO. B13F Parts List for Schematic aAlways Order by Part NO. and I.D. Number Hitachi Koki Canada Co

B13F specifications

The Hitachi B13F is a versatile and robust benchtop drill press designed to meet the demands of both professionals and hobbyists in various applications. Known for its reliability and precision, the B13F combines advanced technology with practical features that make it a popular choice among woodworkers, metalworkers, and those involved in DIY projects.

One of the standout features of the Hitachi B13F is its powerful 350-watt motor, which provides sufficient torque for a wide range of drilling operations. This motor is designed to handle heavier materials, ensuring that users can work with wood, metal, and plastics without compromising on performance. Additionally, the drill press offers a variable speed control system, allowing users to select from a speed range of 580 to 3,050 RPM, making it suitable for drilling different materials with ease and precision.

The B13F's 13mm keyless chuck provides convenience and quick tool changes, reducing setup time and enhancing productivity. This feature allows users to effortlessly switch between drill bits without the need for additional tools, which is especially beneficial for those who require frequent bit changes on the job site or in their workshops.

Precision is a hallmark of the Hitachi B13F, thanks in part to its laser guide system that aids in aligning the drill bit with the target material. This ensures accurate and clean holes, minimizing the risk of error in drilling. The drill press is equipped with an adjustable depth stop, enabling users to set the maximum drilling depth for consistent results across multiple holes.

The construction of the B13F is another highlight, with a sturdy cast iron base that provides stability during operation. This solid foundation minimizes vibrations, contributing to a smoother drilling experience and enhancing the overall accuracy of the tool. The height-adjustable work table also adds flexibility, allowing users to accommodate various workpiece sizes effortlessly.

Moreover, safety features such as the emergency stop switch and a built-in work light further enhance the usability of the Hitachi B13F, ensuring that operators can work efficiently while prioritizing safety.

In summary, the Hitachi B13F benchtop drill press combines power, precision, and convenience in a compact design. With advanced technologies such as variable speed control, a keyless chuck, and laser guiding capabilities, it stands out as a reliable tool for a wide range of drilling tasks, making it an excellent investment for both professional workshops and home garages.
Top Page Image Contents