Hitachi B13F instruction manual Specific Safety Instructions for the Drill Press

Page 5

SPECIFIC SAFETY INSTRUCTIONS FOR THE DRILL PRESS

WARNING

For your own safety, do not try to use your drill press or plug it in until it is completely assembled and installed according to the instrucitons, and until you have read and understood this intstruction manual.

1.THIS DRILL PRESS is intended for use in dry conditions, indoor use only.

2.WEAR EYE PROTECTION. USE a face or dust mask along with safety goggles if drilling operation is dusty. USE ear protectors, especially during extended periods of operation.

3.DO NOT wear gloves, neckties, or loose clothing.

4.DO NOT try to drill material too small to be securely held.

5.ALWAYS keep hands out of the path of a drill bit. Avoid awkward hand positions where a sudden slip could cause your hand to move into the drill bit.

6.DO NOT install or use any drill bit that exceeds 175mm (7″) in length or extends 150mm (6″) below the chuck jaws. They can suddenly bend outward or break.

7.DO NOT USE wire wheels, router bits, shaper cutters, circle (fly) cutters, or rotary planers on this drill press.

8.WHEN cutting a large piece of material, make sure it is fully supported at the table height.

9.DO NOT perform any operation freehand. ALWAYS hold the workpiece firmly against the table so it will not rock or twist. Use clamps or a vise for unstable workpieces.

10.MAKE SURE there are no nails or foreign objects in the part of the workpiece to be drilled.

11.CLAMP THE WORKPIECE OR BRACE IT against the left side of the column to prevent rotation. If it is too short or the table is tilted, clamp it solidly to the table and use the fence provided.

12.IF THE WORKPIECE overhangs the table such that it will fall or tip if not held, clamp it to the table or provide auxiliary support.

13.SECURE THE WORK. Use clamps or a vise to hold the work when practical. It’s safer than using your hand and it frees both hands to operate tool.

English

14.MAKE SURE all clamps and locks are firmly tightened before drilling.

15.SECURELY LOCK THE HEAD and table support to the column, and the table to the table support before operating the drill press.

16.NEVER turn your drill press ON before clearing the table of all objects (tools, scraps of wood, etc.).

17.BEFORE STARTING the operation, jog the motor switch to make sure the frill bit does not wobble or vibrate.

18.LET THE SPINDLE REACH FULL SPEED before starting to drill. If your drill press makes an unfamiliar noise or if it vibrates excessively, stop immediately, turn the drill press OFF and unplug. Do not restart the unit until the problem is corrected.

19.DO NOT perform layout assembly or set up work on the table while the drill press is in operation.

20.USE THE RECOMMENDED SPEED for any drill press accessory and for different workpiece material. READ THE INSTRUCTIONS that come with the accessory.

21.WHEN DRILLING large diameter holes, clamp the workpiece firmly to the table. Otherwise, the bit may grab and spin the workpiece at high speeds. DO NOT USE fly cutters or multiple-part hold cutters, as they can come apart or become unbalanced in use.

22.MAKE SURE the spindle has come to a complete stop before touching the workpiece.

23.TO AVOID INJURY from accidental starting, always turn the switch OFF and unplug the drill press before installing or removing any accessory or attachment or making any adjustment.

24.KEEP GUARDS IN PLACE and in working order.

25.USE ONLY THE SELF-EJECTING TYPE CHUCK KEY as provided with the drill press.

26.AVOID DIRECT EYE EXPOSURE when using the laser guide.

27.ALWAYS ENSURE THE LASER BEAM IS AIMED AT A SURFACE WITHOUT REFLECTIVE PROPERTIES. Shiny reflective materials are not suitable for laser use.

– 5 –

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Hitachi Hitachi Authorized Service Centers NET Weight Product SpecificationsMotor 61 LB 27.5 kgBefore Using the Drill Press SafetyGeneral Safety Instructions Specific Safety Instructions for the Drill Press Guidelines for Extension Cords Electrical RequirementsCarton Contents Accessories and AttachmentsUnpacking Your Drill Press Know Your Drill Press Depth Scale Stop Nuts Lock the spindle to a Glossary of TermsDrill Press Terms Assembly Instructions Assembly and AdjustmentsEstimated Assembly Time 20-40 Minutes Tools NeededInstalling the Head Fig. D Installing Battery for Laser Guide Fig. C-1Installing Feed Handles Fig. E Installing the Chuck Fig. F and GTilting the Table Fig. H Drill Press AdjustmentsSpindle / Quill Fig Quill Return Spring Fig. JLaser Guide Avoid Direct EYE ContactBelt Tension Fig. K Basic Drill Press Operations OperationYour Protection Basic Operation IstructionsDrilling to a Specific Depth Fig. P Removing Chuck and Arbor Fig. RFeeding Positioning the Table and Workpiece Fig. S and TMaintaining Your Drill Press MaintenanceLubrication BatteriesGeneral Troubleshooting GuideProblem Probable Cause Remedy Moteur Spécifications DU ProduitPoids NET 27,5 kg 61 lbAvant D’UTILISER Cette Perceuse SécuritéConsignes DE Sécurité Générales Consignes DE Sécurité Spécifiques À LA Perceuse D’ÉTABLI Directives Pour LES Rallonges Électriques Exigences ÉlectriquesCalibre Minimal Pour Cordons Prolongateurs AWG Avec du 120 V seulementAccessoires Recommandés Accessoires ET ÉquipementsContenu DU Carton Déballage ET Vérification DU ContenuDéballage DE LA Perceuse MARCHE/ARRÊT Connaître SA PerceuseBoutons DE Verrouillage DE Tension DE Glossaire DES TermesÉcrous DE Blocage D’ÉCHELLE DE Interrupteur DE MARCHE/ARRÊT DEInstructions D’ASSEMBLAGE Assemblage ET AjustementsTemps D’ASSEMBLAGE Prévu 35 Minutes Outils RequisInstallation DU Mandrin Fig. F et G Installation DE LA Tête Fig. DInsertion DES Piles Dans LE Guide AU Laser Fig. C-1 Nstallation DES Leviers DE Manoeuvre Fig. EInclinaison DE LA Table Fig. H Réglages DE LA PerceuseBroche / Arbre Creux Fig Ressort DE Rappel DE L’ARBRE Creux Fig. JLE Guide Laser Éviter UN Contact Direct Avec LES YeuxTension DE LA Courroie Fig. K Opérations DE Base DE LA Perceuse FonctionnementVotre Protection Instructions SUR LE Fonctionnement DE BasePerçage À UNE Profondeur Spécifique Fig. P Dépose DU Mandrin ET DE L’ARBRE Fig. RDiam Matériau Du foret Bois Tableau DES Vitesses DE PerçagePlastique Acier Inox DouxEntretien DE LA Perceuse EntretienPositionnement LubrificationProblème Causes Probable Action Corrective Guide DE DépannageMotor Especificaciones DEL ProductoAmperios Peso NetoAntes DE Usar Esta Prensa Taladradora SeguridadInstrucciones Generales DE Seguridad Especificaciones DE LA Alimentacion Electrica Y EL Motor Requisitos ElectricosInstrucciones Para LA Conexion a Tierra Pautas Para EL USO DE Cables DE ExtensionEN Caso DE UN MAL Funcionamiento O UNA Calibre Minimo Para Cables DE Extension AWGContenido DE LA Caja Accesorios Y AditamentosAccesorios Recomendados Desempaque Y Verificacion DEL ContenidoDesempaque DE Prensa Taladradora Conozca SU Prensa Taladradora Manillas DE Fijacion DE LA Tension DE LA Correa Glosario DE TerminosTuercas DE Tope DE LA Escala DE Profundidad Interruptor DE Encendido Y Apagado DEL TaladroHerramientas Necesarias Montaje Y AjustesInstruccioned DE Montaje Instalacion DEL Cabezal Fig. D Instalacion DE LA Bateria Para LA Guia Laser Fig. C-1Instalacion DE LOS Mangos DE Alimentacion Fig. E Instalacion DEL Portabrocas Fig. F y GInclinacion DE LA Mesa Fig. H Ajustes DE LA Prensa TaladradoraHusillo / Manguito Fig Resorte DE Retorno DEL Manguito Fig. JEvite EL Contacto Directo CON LOS Ojos Tension DE LA Correa Fig. KLA Guia Laser Operaciones Basicas DE LA Prensa Taladradora OperacionSU Proteccion Instrucciones Basicas DE OperacionTaladrado a UNA Profundidad Especifica Fig. P Desmontaje DEL Portabrocas Y EL Arbol Fig. RDiám Material De broca Madera Tabla DE Velocidad DE Taladradora RPMPlástico Acero Inoxid Pulg Dulce Colocacion DE LA Mesa Y DE LA Pieza DE Trabajo Fig. S y TDele Mantenimiento a SU Prensa Taladradora MantenimientoAlimentacion LubricacionGeneralidades Guia DE Identificacion DE ProblemasProblema Causa Probable Solucion Model NO. B13F Schematic a10 ″ Bench Drill Press Always Order by Part NO. and I.D. Number Parts List for Schematic a10″ Bench Drill Press Model NO. B13F Hitachi Koki Canada Co

B13F specifications

The Hitachi B13F is a versatile and robust benchtop drill press designed to meet the demands of both professionals and hobbyists in various applications. Known for its reliability and precision, the B13F combines advanced technology with practical features that make it a popular choice among woodworkers, metalworkers, and those involved in DIY projects.

One of the standout features of the Hitachi B13F is its powerful 350-watt motor, which provides sufficient torque for a wide range of drilling operations. This motor is designed to handle heavier materials, ensuring that users can work with wood, metal, and plastics without compromising on performance. Additionally, the drill press offers a variable speed control system, allowing users to select from a speed range of 580 to 3,050 RPM, making it suitable for drilling different materials with ease and precision.

The B13F's 13mm keyless chuck provides convenience and quick tool changes, reducing setup time and enhancing productivity. This feature allows users to effortlessly switch between drill bits without the need for additional tools, which is especially beneficial for those who require frequent bit changes on the job site or in their workshops.

Precision is a hallmark of the Hitachi B13F, thanks in part to its laser guide system that aids in aligning the drill bit with the target material. This ensures accurate and clean holes, minimizing the risk of error in drilling. The drill press is equipped with an adjustable depth stop, enabling users to set the maximum drilling depth for consistent results across multiple holes.

The construction of the B13F is another highlight, with a sturdy cast iron base that provides stability during operation. This solid foundation minimizes vibrations, contributing to a smoother drilling experience and enhancing the overall accuracy of the tool. The height-adjustable work table also adds flexibility, allowing users to accommodate various workpiece sizes effortlessly.

Moreover, safety features such as the emergency stop switch and a built-in work light further enhance the usability of the Hitachi B13F, ensuring that operators can work efficiently while prioritizing safety.

In summary, the Hitachi B13F benchtop drill press combines power, precision, and convenience in a compact design. With advanced technologies such as variable speed control, a keyless chuck, and laser guiding capabilities, it stands out as a reliable tool for a wide range of drilling tasks, making it an excellent investment for both professional workshops and home garages.
Top Page Image Contents