Hitachi DN 12DY instruction manual To use for drilling metal

Page 20

English

NOTE: A buzzing noise is produced when the motor is about to rotate; this is only a noise, not a machine failure.

5.To use for drilling metal

◯In case you drill metal with an iron-working drill bit, apply in advance a center punch in the drilling position. You can drill metal stably since the point of the drill bit does not slip.

◯If you apply sewing machine oil or soapy water to the drill bit with a brush or an old tooth brush, the drill bit will last long.

◯When drilling a hole, it cannot be drilled more rapidly by applying more than the required force. On the contrary, the edge of the drill bit will be damaged. This will decrease operational efficiency and shorten the life of this POWER TOOL.

CAUTION:

⬤The motor rotation may be locked to cease while the Cordless angle drill is used as a drill. The motor must be burnt or the battery life must remarkably be reduced when the locked condition is continued for several seconds.

⬤Drilling a hole in the metal exerts considerable force on the edge of the hole so that the drill bit may slip from the keyless chuck. If this happens, decrease the pushing pressure on the Cordless angle drill so that the drill bit does not slip.

⬤While operating the Cordless angle drill, take care not to lock the motor. If the motor is locked, immediately turn the power off.

⬤Do tighten too strongly as the screw heads will be damaged.

⬤When pressing the tool against the object to be drilled, take care not to touch the keyless chuck with your hands.

20

Image 20

Contents Avertissement AdvertenciaVariable speed Perceuse dangle à batterieContents Important Safety Information Meanings of Signal WordsSafety General Safety Rules for ALL Battery Operated ToolsEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Carefully handle power toolsNever use a tool which is defective or operating abnormally Important Safety Instructions for Battery Charger Remember Disposal of the Exhausted Battery Make Them Available to Other Users Owners of this ToolFunctional Description ModelName of Parts Cordless Angle Drill DN12DYSpecifications Battery ChargerUC14YFA UC24YFA Assembly and Operation Removal and Installation Method of BatteryApplications Charging MethodInsert the battery into the battery charger Insert the plug of battery charger into the receptacleDisconnect battery charger from the receptacle Remove the battery from the battery chargerInsert the battery to the battery charger RED Mounting and dismounting the bit Before USEOperation Check the rotational direction Confirm that the battery is mounted correctlySwitch operation To use for drilling metal Maintenance and Inspection Accessories Standard AccessoriesBattery EB1212S, EB1220BL Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTAvertissement Lire et coxmprendre toutes les instructions SecuriteConserver CES Instructions Avertissement Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesManipuler l’outil motorisé avec précaution Ne pas essuyer les parties en plastique avec du solvantUC24YFA Tableau Mise AU Rebut D’UNE Batterie Usée Français Description Fonctionnelle ModeleNOM DES Parties Perceuse dangle à batterie DN12DYChargeur de batterie UC14YF2/UC14YFA/CU24YFAModèle Méthode DE Recharge Méthode DE Retrait ET D’INSTALLATION DE LA BatterieUtilisations Insérer la batterie dans le chargeur de batterie Brancher la fiche du chargeur de batterie dans la priseRecharge Débrancher le chargeur de batterie de la priseFrançais Comment prolonger la durée de vie des batteries Verte Avant L’UTILISATION Vérifiez si la batterie a été correctement installée UtilisationPose et dépose du foret Vérifiez la direction de rotationFonctionnement de l’interrupteur Utilisation pour percer du métalEntretien ET Inspection Accessoires Accessoires StandardAccessoires EN OPTION.....vendus séparément Batterie EB1212S, EB1220BLInformación Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónAdvertencia Lea y entienda todas las instrucciones SeguridadGuarde Estas Instrucciones Advertencia Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móvilesUtilice la herramienta correcta Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeEspañol Recuerde Eliminación DE LAS Baterías Agotadas Español Descripción Funcional ModeloNomenclatura Taladro angular a batería DN12DYEspecificaciones Cargador de bateríasModelo Montaje Y Operación AplicacionesMétodo DE Extracción E Instalación DE LA Batería Método DE CargaInserte la batería en el cargador de baterías CargaDesconecte el cargador de baterías del tomacorriente Extraiga la batería del cargador de bateríasInserte el enchufe del cargador de baterías En un tomacorrienteVerde Antes DE LA Utilización Operación Montaje y desmontaje de la brocaConfirmar que la batería está puesta correctamente Examinar la dirección de rotaciónOperación del interruptor Cómo proceder para taladrar metalMantenimiento E Inspección Accesorios Accesorios EstándarAccesorios OPCIONALES.....de venta por separado Battería EB1212S, EB1220BLUC24YFA Page Page Page Hitachi Koki Canada Co