Senco PC1108 operating instructions Preparation, Initial SET-UP, Location, Electrical

Page 10

PREPARATION

INITIAL SET-UP:

1.Read safety warnings before setting-up air compressor.

2.Add entire contents of oil from enclosed bottle prior to starting compressor.

3.Ensure the oil level is above the minimum notch and below the maximum notch on the dipstick. If low, add compressor pump oil.

LOCATION:

CAUTION

In order to avoid damaging the air compressor,do not incline the air compressor transversely or longitudinally more than 10 °.

1.Place air compressor at least 12 inches away from obstacles that may prevent proper ventilation. Do not place air compressor in an area:

-where there is evidence of oil or gas leaks.

-where flammable gas vapors or materials may be present.

WARNING

Serious injury or death may occur if electrical sparks from motor and pressure switch come in contact with flammable vapors, combustible dust, gases or other

combustible materials. When using the air compressor for spray painting, place the air compressor as far away from the work area as possible,using extra air hoses instead of extension cords.

-where air temperatures fall below 32 °F or exceed 104 °F.

-where extremely dirty air or water could be drawn into the air compressor.

ELECTRICAL:

DANGER

Improper connection of the equipment-grounding conductor can result in a risk of shock or electrocution. Check with a qualified electrician or service personnel if

you are in doubt as to whether the outlet is properly grounded. Do not use any type of adapter with this product. If repair or replacement of the cord or plug is necessary,do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.

WARNING

This product must be grounded.If there should be a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-

grounding conductor and a grounding type plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

1.Senco ® DOES NOT RECOMMEND THE USE OF EXTENSION CORDS as this can create power loss and overheating of the motor. Use of an additional air hose is recommended rather than an extension cord. If use of an extension cord is unavoidable, it should be plugged into a GFCI found in circuit boxes or protected receptacles. When using an extension cord,observe the following:

Cable Length

Wire Gauge

Up to 25 feet

12 AWG

Up to 100 feet

10 AWG

Up to 150 feet

8 AWG

Up to 250 feet

6 AWG

Use only 3-blade extension cords that have 3-blade grounding-type plugs and 3-slot cord connectors that will accept the plug from the product. Use only extension cords having an electrical rating not less than the rating of the product. Do not use damaged extension cords. Examine extension cord before using and replace if damaged. Do not abuse extension cord and do not yank on any cord to disconnect. Keep cord away from heat and sharp edges. Always shut off the air compressor switch before removing the plug from the receptacle.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operating Instructions Table of Contents Introduction Safety AlertInspection Electric Shock Safety WarningsHazard Potential Consequence Prevention Risk ElectrocutionExplosion or Fire BurstingBurns Hazard Potential Consequence Prevention Risk toBreathing FlyingNegligence Hazard Potential Consequence Prevention Risk fromMoving Parts AIR Compressor DamageCompressor Features Wheel Location PreparationInitial SET-UP ElectricalMaintenance OperationRemedy TroubleshootingProbable Cause Probable Cause RemedySymptom 5. Air leaks from safety relief valve Symptom 10. Air compressor not making enough air Specifications Senco PCSenco Compressor and Parts Warranty Compresseurdaire eléctrique PC1108 Mises EN Garde DE Sécurité Table DES MatièresCaractéristiques DU Compresseur Alertes Pour LA Sécurité Mises EN Garde DE Sécurité Commotion Électrique OU D’ÉLECTROCUTIONOU D’INCENDIE Compresseur D’AIRConséquences Potentielles Prévention Risque D’EXPLOSION RisqueRisque DE Brûlure Conséquences Potentielles Prévention Risque’INHALATION ’OBJETSConservez CES Instructions Caractéristiques DU Compresseur Caractéristiques DU Compresseur Mise EN Œuvre Initiale EmplacementPréparation AvertissementDémarrage FonctionnementListe DE Vérifications Préliminaires CoupureRemède DépannageCause Probable Cause Probable RemèdeSymptôme 5 L’air fuit au niveau de la soupape de sûreté Symptôme 11 Humidité dans l’air en sortie Spécifications Garantie Senco Pour LE Compresseur ET LES Pièces Instruccione de Operación Indice ¡AVISO DE Seguridad IntroducciónInspección Electrochoque Medidas DE SeguridadRiesgo Consecuencia Potencial Prevención Riesgo DE ElectrocuciónIncendio EstallidoQuemaduras Riesgo Potential Consequence Prevención Riesgo Para LASVias Respiratorias Riesgo DE SER¡GUARDE Estas Instrucciones Características DEL Compresor Características DEL Compresor Emplazamiento PreparaciónMontaje Inicial AdvertenciaLista DE Comprobación Antes DE LA Puesta EN Marcha FuncionamientoCuadro DE Mantenimiento Solución Localización Y Solución DE AveríasCausa Probable Causa Probable SoluciónSíntoma 5. Escape de aire por la válvula de seguridad Síntoma 10. El compresor no produce suficiente aire Especificaciones MotorGarantia Senco Para EL Compresor Y LAS Piezas

PC1108 specifications

The Senco PC1108 is a powerful and versatile pneumatic nail gun designed for both professional contractors and DIY enthusiasts. This tool stands out for its robust performance, user-friendly features, and reliability, making it a favorite for a variety of nailing applications.

One of the main features of the Senco PC1108 is its lightweight design, weighing just 3.5 pounds. This makes it easy to handle and reduces fatigue during extended use. The gun is equipped with a powerful motor that can drive up to 120 nails per minute, allowing users to complete projects quickly and efficiently. It uses 18-gauge nails, which provide a strong hold while minimizing damage to the materials being fastened.

The Senco PC1108 also boasts an adjustable depth-of-drive feature, enabling users to control how deep the nails are driven into the material. This ensures a professional finish and is particularly useful when working with different materials or when precision is required.

Another notable technology incorporated in the Senco PC1108 is its air filter and dual lubrication system. The air filter helps keep dust and debris out of the tool, extending its lifespan and ensuring smooth operation. The dual lubrication system ensures that all moving parts are well-lubricated, further enhancing performance and durability over time.

The nail gun features a 360-degree adjustable exhaust, which allows users to direct exhaust airflow away from their face and work surface. This design enhances comfort and visibility when working in tight spaces. Additionally, the tool includes a quick-release nose design, making it easy to clear jams without needing additional tools, which can save valuable time on the job.

Durability is another key characteristic of the Senco PC1108. Constructed with high-quality materials, it is built to withstand the rigors of daily use on job sites. The rubberized grip provides added comfort and control, making it suitable for both horizontal and vertical nailing tasks.

In summary, the Senco PC1108 is an impressive pneumatic nail gun that combines power, versatility, and advanced features. With its lightweight design, powerful performance, and user-friendly technologies, it is an essential tool for any professional or DIY nailing application.
Top Page Image Contents