HP xw460c Blade manual Route Map configuration, Ap AS number AS number AS, Lp 0-4294967294 none

Page 126

The following table describes the Network Filter Configuration Menu options.

Table 127 Network Filter Configuration Menu options

Command

Description

 

 

addr <IP address>

Sets the starting IP address for this filter. The default address is 0.0.0.0

 

 

mask <IP subnet mask>

Sets the IP subnet mask that is used with /cfg/l3/nwf/addr to define the

 

range of IP addresses that will be accepted by the peer when the filter is

 

enabled. The default value is 0.0.0.0

 

 

enable

Enables the Network Filter configuration.

 

 

disable

Disables the Network Filter configuration.

 

 

delete

Deletes the Network Filter configuration.

 

 

current

Displays the current the Network Filter configuration.

 

 

Route Map configuration

Command: /cfg/l3/rmap <1-32>

 

[IP Route Map

1

Menu]

 

alist

- Access List number

 

aspath

- AS Filter Menu

 

ap

- Set as-path prepend of the matched route

 

lp

- Set local-preference of the matched route

 

metric

- Set metric of the matched route

 

type

- Set OSPF metric-type of the matched route

 

prec

- Set the precedence of this route map

 

weight

- Set weight of the matched route

 

enable

- Enable route map

 

disable

- Disable route map

 

delete

- Delete route map

 

current

- Display current route map configuration

 

 

 

 

 

 

 

 

 

 

NOTE: This menu is available only on the GbE2c Layer 2/3 Ethernet Blade Switch.

Routing maps control and modify routing information. The map number (1-32) represents the routing map you wish to configure.

The following table describes the Route Map Configuration Menu options. Table 128 Route Map Configuration Menu options

Command

Description

 

 

 

alist <1-8>

Displays the Access List menu.

 

 

 

aspath <1-8>

Displays the Autonomous System (AS) Filter menu.

 

 

 

ap <AS number> [<AS number>] [<AS

Sets the AS path preference of the matched route. One to three path

number>]none

preferences can be configured.

 

 

 

lp <0-4294967294>none

Sets the local preference of the matched route, which affects both

 

inbound and outbound directions. The path with the higher preference is

 

preferred.

 

 

 

metric <0-4294967294>none

Sets the metric of the matched route.

 

 

 

type 12none

Assigns the type of OSPF metric. The default is type 1.

 

• Type 1—External routes are calculated using both internal and

 

external metrics.

 

• Type 2—External routes are calculated using only the external

 

metrics. Type 2 routes have more cost than Type 2.

 

• none—Removes the OSPF metric.

 

 

 

prec <1-256>

Sets the precedence of the route map. The smaller the value, the higher

 

the precedence. Default value is 10.

 

 

 

weight <0-65534>none

Sets the weight of the route map.

 

 

 

 

Configuration Menu 126

Page 125 Page 127
Image 126
Page 125 Page 127
Contents HP GbE2c Ethernet Blade Switch for c-Class BladeSystem Page Contents Statistics Menu Configuration Menu 111 Index Command line interface Additional references Connecting to the switchIntroduction Establishing a console connectionEstablishing a Telnet connection Setting an IP addressTelnet GbE2c Ethernet Blade Switch IP address Establishing an SSH connectionAccessing the switch # ssh user@GbE2c Ethernet Blade Switch IP addressIdle timeout Typographical conventions AaBbCc123Main Menu Menu summaryGlobal commands DelayTraceroute host name IP address max-hops msec Command line history and editing Telnet hostname IP address portCommand abbreviation Command line interface shortcutsCommand stacking Tab completionMain# /cfg Configuring Simple Network Management Protocol support# /cfg/sys/access/snmp disableread onlyread/write # /cfg/sys/ssnmp/rcommwcommSetting passwords Changing the default administrator passwordSystem# apply System# save Changing the default user password Changing the default operator password Information Menu Menu overviewSystem Information Menu SNMPv3 Information MenuComm AdminshaSNMPv3 USM User Table information V1v2onlySNMPv3 Access Table information SNMPv3 View Table informationSNMPv3 Group Table information SNMPv3 Community Table informationPrefix SNMPv3 Target Address Table information SNMPv3 Target Parameters Table informationCommand /info/sys/snmpv3/notify NameTag V1v2trapv1v2trap SNMPv3 Notify Table informationSec Level SNMPv3 dump System information Show last 100 syslog messages System user informationCfg/sys/access/user/uid command Layer 2 information8021x Stp FDB information menu Find MAC address VlanPort port number Link Aggregation Control Protocol information Show all FDB informationLacp dump 802.1x information Command /info/l2/stp Port Auth ModeAuthenticator PAE State Spanning Tree informationPriority bridge Current RootPath-Cost HelloDesg 8017 P2P2,Edge Rapid Spanning Tree and Multiple Spanning Tree informationDesignated port Desg 8018Disabled DSB Common Internal Spanning Tree information Disabled DSB Trunk group informationDiscarding Disc , Learning LRN , Forwarding FWD , or Vlan information Layer 2 general informationLayer 3 information Gw IP address Route informationFind IP address If IP addressShow all IP Route information Show all ARP entry information Command /info/arp/dump IP address Flags MAC addressARP information VlanOspf information Nbr nbr router-id A.B.C.DDbase Sumaddr Nsumadd Routes Dump Ospf general information Ospf interface informationOspf Database information menu Ext adv-rtr A.B.C.D linkstateid A.B.C.Dself Advrtr router-id A.B.C.DAsbrsum adv-rtr A.B.C.D Linkstateid A.B.C.Dself Nw adv-rtr A.B.C.D linkstateid A.B.C.DselfOspf route codes information Routing Information Protocol informationRIP Routes information RIP user configuration IP informationIgmp multicast group information Command /info/l3/vrrp Vrrp information Igmp multicast router port informationVrrp information QoS Menu 8021p Show QOS 802.1p information QoS information802.1p information 8021pACL information Rmon Information MenuRmon history information IntervalRmon alarm information Command /info/rmon/eventRmon event information Link status information Command /info/port Port Tag Rmon Pvid Port informationVLANs Logical Port to GEA Port mapping Command /info/geaport Logical Port GEA Port0-based GEA UnitUplink Failure Detection Enabled LtM status Down Member Uplink Failure Detection informationCommand /info/dump Information dumpMenu information Ntp clearUfd clear Port Statistics Menu Authenticating 802.1x statisticsAuthSuccessesWhile Bridging statistics BackendNonNakResponsesFromSupplicant Ethernet statistics Dot3StatsSingleCollisionFrames Dot3StatsFCSErrorsDot3StatsInternalMacTransmitErrors Dot3StatsMultipleCollisionFramesInterface statistics Internet Protocol IP statistics Link statisticsPort Rmon statistics Layer 2 statistics FDB statisticsArp clear Lacp statisticsLayer 3 statistics Clrigmp 1- 4095 allIP statistics GEA Layer 3 statistics menuGEA Layer 3 statistics L3 bucket for An IP address DumpRoute statistics ARP statisticsDNS statistics Icmp statisticsTCP statistics UDP statistics Ospf statistics menu Command /stats/l3/ospfIgmp Multicast Group statistics Ospf stats MenuOspf global statistics Tx ls Updates Nbr changeTimers Kickoff Vrrp statisticsRIP statistics Command /stats/l3/ripManagement Processor statistics Packet statisticsAllocs 10ad41e8/10ad5790Access Control List ACL statistics menu CPU statisticsACL statistics Snmp statistics Only NTP statistics Statistics dump Command /stats/dumpUplink Failure Detection statistics Number of times LtM link in BlockingConfiguration Menu Viewing pending changes Saving the configurationViewing, applying, reverting, and saving changes Applying pending changesSystem configuration RemindersBannr 1-80 characters System host log configurationLine to end Host IP addressSecure Shell Server configuration Console disableenableLog featureall enabledisable Intrval Radius server configurationCommand /cfg/sys/radius Sshport TCP port numberTACACS+ server configuration Telnet enabledisable Port TCP port numberDlight disableenable NTP server configurationSystem Snmp configuration Command /cfg/sys/ssnmpSNMPv3 configuration Name 1-64 charactersCharacters User Security Model configuration V1v2 disableenableTree 1-32 characters SNMPv3 View configurationName 1-32 characters Mask 1-32 charactersUsmsnmpv1snmpv2 Level View-based Access Control Model configurationSNMPv3 Group configuration NoAuthNoPrivauthNoSNMPv3 Community Table configuration Usmsnmpv1snmpv2 UnameDel Deletes the vacmSecurityToGroup entry Cur Addr transport SNMPv3 Target Address Table configurationSNMPv3 Target Parameters Table configuration Address ip Port transportSNMPv3 Notify Table configuration Snmpv1snmpv2csnmp ModelSystem Access configuration Management Networks configurationUser Access Control configuration User ID configurationUseroperadmin Name Port configuration Https Access configurationAccess enabledisable Name 1-64 characters none Port link configuration Temporarily disabling a portLayer 2 configuration 802.1x configurationPort ACL/QoS configuration 802.1x Global configuration Mode forceUnauthautoforce-auth 802.1x Port configuration Reauth onoffMode rstpmstp RevPort parameter menu Common Internal Spanning Tree configurationBridge parameter menu 4095Cist bridge configuration Cist port configurationCost Spanning Tree configurationEdge disableenable Link autop2psharedBridge Spanning Tree configuration Spanning Tree port configuration Cur Display current port Spanning Tree parametersForwarding Database configuration Static FDB configurationFastfwd disableenable Clear mac MAC AddressVLAN 1-4095 Port port numberAll Trunk configurationMAC address Vlan port Add port numberIP Trunk Hash configuration Layer 2 IP Trunk Hash configurationLink Aggregation Control Protocol configuration Timeout shortlong Lacp Port configurationVlan configuration Mode offactivepassiveLayer 3 configuration Port numberList of port numbers IP interface configuration Addr IP addressMask IP subnet mask IP Static Route configuration Default Gateway configurationNetwork Filter configuration Address Resolution Protocol configurationIP Forwarding configuration Dirbr disableenableRoute Map configuration Ap AS number AS number ASLp 0-4294967294 none Metric 1-4294967294none IP Access List configurationAutonomous System Path configuration Action permitdenyRouting Information Protocol configuration RIP Interface configuration Add 1-32 1-32all Open Shortest Path First configurationRIP Route Redistribution configuration Remove 1-32 1-32allMd5key 1-255 characters Osfp Area Index configurationDefault 1-16777215 12none Redist fixedstaticripAreaid IP address Ospf Summary Range configurationAuth nonepasswordmd5 Type transitstubnssaKey key stringnone Ospf Interface configurationMask IP address mask Mdkey 1-255noneOspf Virtual Link configuration Key passwordNbr IP address Rem 1-32 1-32 ... all Ospf Host Entry configurationOspf Route Redistribution configuration Export 1-16777215 12noneIgmp configuration Ospf MD5 Key configurationFastlv 1-4095 disableenable Igmp snooping configurationAggr disableenable Srcip IP addressAdd port number 1-4095 Igmp static multicast router configurationIgmp filtering configuration FilterRange IP multicast address IP Igmp filtering port configurationIgmp filter definition Multicast addressBootstrap Protocol Relay configuration Domain Name System configurationVirtual Router Redundancy Protocol configuration Vrrp Virtual Router configurationPreem disableenable Vrs disableenable Vrrp Virtual Router Priority Tracking configurationVrrp Virtual Router Group configuration Ifs disableenableVrrp Virtual Router Group Priority Tracking configuration Vrrp Interface configuration Vrrp Tracking configurationPassw password Quality of Service configuration Access Control configurationQoS 802.1p configuration Action permitdenysetprio Access Control List configurationEgrport port number Stats edACL Ethernet Filter configuration ACL IP Version 4 Filter configurationACL TCP/UDP Filter configuration Sport 1-65535 port maskFlags value 0x0-0x3f Enable ed ACL Meter configurationACL Re-mark configuration CirACL Re-mark In-Profile configuration ACL Re-mark In-Profile Update User Priority configurationACL Re-mark Out-of-Profile configuration Remote Monitoring configuration ACL Packet Format configurationACL Group configuration Rmon history configuration Ifoid 1-127 charactersOwner 1-127 characters Descn 1-127 characters Rmon event configurationRmon alarm configuration Type nonelogtrapboth2147483647 Port mirroringRlimit -2147483647 to Flimit -2147483647 toAdd mirrored port inoutboth Uplink Failure Detection configurationPort-based port mirroring Rem mirrored portAddport port number Failure Detection Pair configurationLink to Monitor configuration Remport port numberDump Saving the active switch configurationLink to Disable configuration Addport port number Remport port numberRestoring the active switch configuration Command /cfg/gtcfg FTP/TFTP server filenameConfiguration# gtcfg FTP/TFTP server filename Operations Menu Operations-level port optionsReset Reauth Operations-level port 802.1x optionsOperations-level Vrrp options Updating the switch software image Downloading new software to the switchSelecting a software image to run AddressBoot Options# ptimg Uploading a software image from the switchSelecting a configuration block Boot Options# confBoot Options# reset Resetting the switchAccessing the Iscli Boot Options# curMaintenance Menu Flags new Nvram flags word as System maintenance optionsForwarding Database options 0xXXXXXXXXDebugging options ARP cache optionsIP Route Manipulation options Igmp Multicast Group optionsBroadcastmartian Igmp Snooping options Igmp Mrouter optionsUuencode flash dump FTP/TFTP system dump putClearing dump information Confirm dump and reboot y/n y Panic commandCommand /maint/panic Unscheduled system dumpsIndex
Related manuals
Manual 33 pages 57.51 Kb
Top Page Image Contents