HP xw460c Blade manual Bootstrap Protocol Relay configuration, Domain Name System configuration

Page 140

Domain Name System configuration

Command: /cfg/l3/dns

[Domain Name System

Menu]

prima

- Set

IP

address of primary DNS server

secon

- Set

IP

address of secondary DNS server

dname

- Set

default domain name

cur

- Display current DNS configuration

 

 

 

 

The Domain Name System (DNS) Configuration Menu is used for defining the primary and secondary DNS servers on your local network, and for setting the default domain name served by the switch services. DNS parameters must be configured prior to using hostname parameters with the ping, traceroute, and tftp commands.

The following table describes the Domain Name System (DNS) Configuration Menu options.

Table 148 Domain Name System (DNS) Configuration Menu options

Command

Description

 

 

prima <IP address>

Sets the IP address for your primary DNS server. Use dotted

 

decimal notation. For example, 192.4.17.41

 

 

secon <IP address>

Sets the IP address for your secondary DNS server. If the

 

primary DNS server fails, the configured secondary will be

 

used instead. Enter the IP address using dotted decimal

 

notation. For example, 192.4.17.42

 

 

dname <dotted DNS notation>none

Sets the default domain name used by the switch.

 

For example: mycompany.com

 

 

cur

Displays the current Domain Name System (DNS) settings.

 

 

Bootstrap Protocol Relay configuration

Command: /cfg/l3/bootp

 

[Bootstrap Protocol

Relay Menu]

 

addr

- Set

IP address of BOOTP server

 

addr2

- Set

IP address of second BOOTP server

 

on

- Globally turn BOOTP relay ON

 

off

- Globally turn BOOTP relay OFF

 

cur

- Display current BOOTP relay configuration

 

 

 

 

 

 

 

 

 

 

NOTE: This menu is available only on the GbE2c Layer 2/3 Ethernet Blade Switch.

The Bootstrap Protocol (BOOTP) Relay Menu is used to allow hosts to obtain their configurations from a Dynamic Host Configuration Protocol (DHCP) server. The BOOTP configuration enables the switch to forward a client request for an IP address to two DHCP/BOOTP servers with IP addresses that have been configured on the GbE2c.

BOOTP relay is turned off by default.

The following table describes the BOOTP Configuration Menu options.

Table 149 BOOTP Configuration Menu options

Command

Description

 

 

addr <IP address>

Sets the IP address of the BOOTP server. For example,

 

100.10.1.1

 

 

addr2 <IP address>

Sets the IP address of the secondary BOOTP server. For example,

 

100.10.1.2

 

 

on

Globally turns on BOOTP relay.

 

 

off

Globally turns on BOOTP relay.

 

 

cur

Displays the current BOOTP relay configuration.

 

 

Configuration Menu 140

Page 139 Page 141
Image 140
Page 139 Page 141
Contents HP GbE2c Ethernet Blade Switch for c-Class BladeSystem Page Contents Statistics Menu Configuration Menu 111 Index Command line interface Connecting to the switch IntroductionAdditional references Establishing a console connectionSetting an IP address Telnet GbE2c Ethernet Blade Switch IP addressEstablishing a Telnet connection Establishing an SSH connectionAccessing the switch # ssh user@GbE2c Ethernet Blade Switch IP addressIdle timeout Typographical conventions AaBbCc123Main Menu Menu summaryTraceroute host name IP address max-hops msec Global commandsDelay Command line history and editing Telnet hostname IP address portCommand line interface shortcuts Command stackingCommand abbreviation Tab completionConfiguring Simple Network Management Protocol support # /cfg/sys/access/snmp disableread onlyread/writeMain# /cfg # /cfg/sys/ssnmp/rcommwcommSystem# apply System# save Setting passwordsChanging the default administrator password Changing the default user password Changing the default operator password Information Menu Menu overviewSystem Information Menu SNMPv3 Information MenuAdminsha SNMPv3 USM User Table informationComm V1v2onlySNMPv3 Access Table information SNMPv3 View Table informationPrefix SNMPv3 Group Table informationSNMPv3 Community Table information SNMPv3 Target Address Table information SNMPv3 Target Parameters Table informationSec Level Command /info/sys/snmpv3/notify NameTag V1v2trapv1v2trapSNMPv3 Notify Table information SNMPv3 dump System information Show last 100 syslog messages System user information8021x Stp Cfg/sys/access/user/uid commandLayer 2 information Port port number FDB information menuFind MAC address Vlan Link Aggregation Control Protocol information Show all FDB informationLacp dump 802.1x information Port Auth Mode Authenticator PAE StateCommand /info/l2/stp Spanning Tree informationCurrent Root Path-CostPriority bridge HelloRapid Spanning Tree and Multiple Spanning Tree information Designated portDesg 8017 P2P2,Edge Desg 8018Disabled DSB Common Internal Spanning Tree information Discarding Disc , Learning LRN , Forwarding FWD , or Disabled DSBTrunk group information Layer 3 information Vlan informationLayer 2 general information Route information Find IP addressGw IP address If IP addressShow all IP Route information Command /info/arp/dump IP address Flags MAC address ARP informationShow all ARP entry information VlanDbase Sumaddr Nsumadd Routes Dump Ospf informationNbr nbr router-id A.B.C.D Ospf Database information menu Ospf general informationOspf interface information Advrtr router-id A.B.C.D Asbrsum adv-rtr A.B.C.D Linkstateid A.B.C.DselfExt adv-rtr A.B.C.D linkstateid A.B.C.Dself Nw adv-rtr A.B.C.D linkstateid A.B.C.DselfRIP Routes information Ospf route codes informationRouting Information Protocol information Igmp multicast group information RIP user configurationIP information Vrrp information Command /info/l3/vrrp Vrrp informationIgmp multicast router port information QoS information 802.1p informationQoS Menu 8021p Show QOS 802.1p information 8021pACL information Rmon Information MenuRmon history information IntervalRmon event information Rmon alarm informationCommand /info/rmon/event Link status information VLANs Command /info/port Port Tag Rmon PvidPort information Command /info/geaport Logical Port GEA Port0-based GEA Unit Uplink Failure Detection Enabled LtM status Down MemberLogical Port to GEA Port mapping Uplink Failure Detection informationCommand /info/dump Information dumpUfd clear Menu informationNtp clear Port Statistics Menu AuthSuccessesWhile Authenticating802.1x statistics Supplicant Bridging statisticsBackendNonNakResponsesFrom Ethernet statistics Dot3StatsFCSErrors Dot3StatsInternalMacTransmitErrorsDot3StatsSingleCollisionFrames Dot3StatsMultipleCollisionFramesInterface statistics Internet Protocol IP statistics Link statisticsPort Rmon statistics Layer 2 statistics FDB statisticsLacp statistics Layer 3 statisticsArp clear Clrigmp 1- 4095 allGEA Layer 3 statistics menu GEA Layer 3 statisticsIP statistics L3 bucket for An IP address DumpRoute statistics ARP statisticsDNS statistics Icmp statisticsTCP statistics UDP statistics Command /stats/l3/ospf Igmp Multicast Group statisticsOspf statistics menu Ospf stats MenuOspf global statistics Tx ls Updates Nbr changeTimers Kickoff Vrrp statisticsCommand /stats/l3/rip Management Processor statisticsRIP statistics Packet statisticsAllocs 10ad41e8/10ad5790ACL statistics Access Control List ACL statistics menuCPU statistics Snmp statistics Only NTP statistics Command /stats/dump Uplink Failure Detection statisticsStatistics dump Number of times LtM link in BlockingConfiguration Menu Saving the configuration Viewing, applying, reverting, and saving changesViewing pending changes Applying pending changesSystem configuration RemindersSystem host log configuration Line to endBannr 1-80 characters Host IP addressLog featureall enabledisable Secure Shell Server configurationConsole disableenable Radius server configuration Command /cfg/sys/radiusIntrval Sshport TCP port numberTACACS+ server configuration Telnet enabledisable Port TCP port numberNTP server configuration System Snmp configurationDlight disableenable Command /cfg/sys/ssnmpCharacters SNMPv3 configurationName 1-64 characters User Security Model configuration V1v2 disableenableSNMPv3 View configuration Name 1-32 charactersTree 1-32 characters Mask 1-32 charactersView-based Access Control Model configuration SNMPv3 Group configurationUsmsnmpv1snmpv2 Level NoAuthNoPrivauthNoDel Deletes the vacmSecurityToGroup entry Cur SNMPv3 Community Table configurationUsmsnmpv1snmpv2 Uname SNMPv3 Target Address Table configuration SNMPv3 Target Parameters Table configurationAddr transport Address ip Port transportSNMPv3 Notify Table configuration Snmpv1snmpv2csnmp ModelSystem Access configuration Management Networks configurationUseroperadmin Name User Access Control configurationUser ID configuration Access enabledisable Port configurationHttps Access configuration Name 1-64 characters none Port link configuration Temporarily disabling a portPort ACL/QoS configuration Layer 2 configuration802.1x configuration Unauthautoforce-auth 802.1x Global configurationMode force 802.1x Port configuration Reauth onoffMode rstpmstp RevCommon Internal Spanning Tree configuration Bridge parameter menuPort parameter menu 4095Cist bridge configuration Cist port configurationSpanning Tree configuration Edge disableenableCost Link autop2psharedBridge Spanning Tree configuration Spanning Tree port configuration Cur Display current port Spanning Tree parametersFastfwd disableenable Forwarding Database configurationStatic FDB configuration Trunk configuration MAC address Vlan portClear mac MAC AddressVLAN 1-4095 Port port numberAll Add port numberLink Aggregation Control Protocol configuration IP Trunk Hash configurationLayer 2 IP Trunk Hash configuration Lacp Port configuration Vlan configurationTimeout shortlong Mode offactivepassiveList of port numbers Layer 3 configurationPort number Mask IP subnet mask IP interface configurationAddr IP address IP Static Route configuration Default Gateway configurationAddress Resolution Protocol configuration IP Forwarding configurationNetwork Filter configuration Dirbr disableenableLp 0-4294967294 none Route Map configurationAp AS number AS number AS IP Access List configuration Autonomous System Path configurationMetric 1-4294967294none Action permitdenyRouting Information Protocol configuration RIP Interface configuration Open Shortest Path First configuration RIP Route Redistribution configurationAdd 1-32 1-32all Remove 1-32 1-32allOsfp Area Index configuration Default 1-16777215 12noneMd5key 1-255 characters Redist fixedstaticripOspf Summary Range configuration Auth nonepasswordmd5Areaid IP address Type transitstubnssaOspf Interface configuration Mask IP address maskKey key stringnone Mdkey 1-255noneNbr IP address Ospf Virtual Link configurationKey password Ospf Host Entry configuration Ospf Route Redistribution configurationRem 1-32 1-32 ... all Export 1-16777215 12noneIgmp configuration Ospf MD5 Key configurationIgmp snooping configuration Aggr disableenableFastlv 1-4095 disableenable Srcip IP addressIgmp static multicast router configuration Igmp filtering configurationAdd port number 1-4095 FilterIgmp filtering port configuration Igmp filter definitionRange IP multicast address IP Multicast addressBootstrap Protocol Relay configuration Domain Name System configurationVirtual Router Redundancy Protocol configuration Vrrp Virtual Router configurationPreem disableenable Vrrp Virtual Router Priority Tracking configuration Vrrp Virtual Router Group configurationVrs disableenable Ifs disableenableVrrp Virtual Router Group Priority Tracking configuration Passw password Vrrp Interface configurationVrrp Tracking configuration QoS 802.1p configuration Quality of Service configurationAccess Control configuration Access Control List configuration Egrport port numberAction permitdenysetprio Stats edACL Ethernet Filter configuration ACL IP Version 4 Filter configurationFlags value 0x0-0x3f ACL TCP/UDP Filter configurationSport 1-65535 port mask ACL Meter configuration ACL Re-mark configurationEnable ed CirACL Re-mark Out-of-Profile configuration ACL Re-mark In-Profile configurationACL Re-mark In-Profile Update User Priority configuration ACL Group configuration Remote Monitoring configurationACL Packet Format configuration Owner 1-127 characters Rmon history configurationIfoid 1-127 characters Rmon event configuration Rmon alarm configurationDescn 1-127 characters Type nonelogtrapbothPort mirroring Rlimit -2147483647 to2147483647 Flimit -2147483647 toUplink Failure Detection configuration Port-based port mirroringAdd mirrored port inoutboth Rem mirrored portFailure Detection Pair configuration Link to Monitor configurationAddport port number Remport port numberSaving the active switch configuration Link to Disable configurationDump Addport port number Remport port numberConfiguration# gtcfg FTP/TFTP server filename Restoring the active switch configurationCommand /cfg/gtcfg FTP/TFTP server filename Operations Menu Operations-level port optionsOperations-level Vrrp options Reset ReauthOperations-level port 802.1x options Updating the switch software image Downloading new software to the switchSelecting a software image to run AddressUploading a software image from the switch Selecting a configuration blockBoot Options# ptimg Boot Options# confResetting the switch Accessing the IscliBoot Options# reset Boot Options# curMaintenance Menu System maintenance options Forwarding Database optionsFlags new Nvram flags word as 0xXXXXXXXXDebugging options ARP cache optionsBroadcastmartian IP Route Manipulation optionsIgmp Multicast Group options Igmp Snooping options Igmp Mrouter optionsClearing dump information Uuencode flash dumpFTP/TFTP system dump put Panic command Command /maint/panicConfirm dump and reboot y/n y Unscheduled system dumpsIndex
Related manuals
Manual 33 pages 57.51 Kb
Top Page Image Contents