HP xw460c Blade manual Configuring Simple Network Management Protocol support, Main# /cfg

Page 18

First-time configuration

Introduction

This chapter describes how to perform first-time configuration and how to change system passwords. To begin first-time configuration of the switch, perform the following steps.

1.Connect to the switch console. After connecting, the login prompt displays.

GbE2c Ethernet Blade Switch for HP c-Class Blade System.

Copyright(C)2006 Hewlett-Packard Development Company, L.P.

Password:

2.Enter admin as the default administrator password.

The system displays the Main Menu with administrator privileges.

[Main Menu]
info	- Information Menu
stats	- Statistics Menu
cfg	- Configuration Menu
oper	- Operations Command Menu
boot	- Boot Options Menu
maint	- Maintenance Menu
diff	- Show pending config changes [global command]
apply	- Apply pending config changes [global command]
save	- Save updated config to FLASH [global command]
revert	- Revert pending or applied changes [global command]
exit	- Exit [global command, always available]
>> Main#

3. From the Main Menu, enter the following command to access the Configuration Menu:

Main# /cfg

The Configuration Menu is displayed.

[Configuration Menu]

sys	- System-wide Parameter Menu
port	- Port Menu
l2	- Layer 2 Menu
l3	- Layer 3 Menu
qos	- QOS Menu
acl	- Access Control List Menu
rmon	- RMON Menu
pmirr	- Port Mirroring Menu
ufd	- Uplink Failure Detection Menu
dump	- Dump current configuration to script file
ptcfg	- Backup current configuration to FTP/TFTP server
gtcfg	- Restore current configuration from FTP/TFTP server
cur	- Display current configuration

Configuring Simple Network Management Protocol support

NOTE: SNMP support is enabled by default.

1.Use the following command to enable SNMP:

>># /cfg/sys/access/snmp disableread onlyread/write

2.Set SNMP read or write community string. By default, they are public and private respectively:

>># /cfg/sys/ssnmp/rcommwcomm

3.When prompted, enter the proper community string.

4.Apply and save configuration if you are not configuring the switch with Telnet support. Otherwise apply and save after the performing the “Optional Setup for Telnet Support” steps.

First-time configuration 18

Image 18

Contents HP GbE2c Ethernet Blade Switch for c-Class BladeSystem Page Contents Statistics Menu Configuration Menu 111 Index Command line interface Additional references Connecting to the switchIntroduction Establishing a console connectionEstablishing a Telnet connection Setting an IP addressTelnet GbE2c Ethernet Blade Switch IP address Establishing an SSH connectionAccessing the switch # ssh user@GbE2c Ethernet Blade Switch IP addressIdle timeout Typographical conventions AaBbCc123Main Menu Menu summaryGlobal commands DelayTraceroute host name IP address max-hops msec Command line history and editing Telnet hostname IP address portCommand abbreviation Command line interface shortcutsCommand stacking Tab completionMain# /cfg Configuring Simple Network Management Protocol support# /cfg/sys/access/snmp disableread onlyread/write # /cfg/sys/ssnmp/rcommwcommSetting passwords Changing the default administrator passwordSystem# apply System# save Changing the default user password Changing the default operator password Information Menu Menu overviewSystem Information Menu SNMPv3 Information MenuComm AdminshaSNMPv3 USM User Table information V1v2onlySNMPv3 Access Table information SNMPv3 View Table informationSNMPv3 Group Table information SNMPv3 Community Table informationPrefix SNMPv3 Target Address Table information SNMPv3 Target Parameters Table informationCommand /info/sys/snmpv3/notify NameTag V1v2trapv1v2trap SNMPv3 Notify Table informationSec Level SNMPv3 dump System information Show last 100 syslog messages System user informationCfg/sys/access/user/uid command Layer 2 information8021x Stp FDB information menu Find MAC address VlanPort port number Link Aggregation Control Protocol information Show all FDB informationLacp dump 802.1x information Command /info/l2/stp Port Auth ModeAuthenticator PAE State Spanning Tree informationPriority bridge Current RootPath-Cost HelloDesg 8017 P2P2,Edge Rapid Spanning Tree and Multiple Spanning Tree informationDesignated port Desg 8018Disabled DSB Common Internal Spanning Tree information Disabled DSB Trunk group informationDiscarding Disc , Learning LRN , Forwarding FWD , or Vlan information Layer 2 general informationLayer 3 information Gw IP address Route informationFind IP address If IP addressShow all IP Route information Show all ARP entry information Command /info/arp/dump IP address Flags MAC addressARP information VlanOspf information Nbr nbr router-id A.B.C.DDbase Sumaddr Nsumadd Routes Dump Ospf general information Ospf interface informationOspf Database information menu Ext adv-rtr A.B.C.D linkstateid A.B.C.Dself Advrtr router-id A.B.C.DAsbrsum adv-rtr A.B.C.D Linkstateid A.B.C.Dself Nw adv-rtr A.B.C.D linkstateid A.B.C.DselfOspf route codes information Routing Information Protocol informationRIP Routes information RIP user configuration IP informationIgmp multicast group information Command /info/l3/vrrp Vrrp information Igmp multicast router port informationVrrp information QoS Menu 8021p Show QOS 802.1p information QoS information802.1p information 8021pACL information Rmon Information MenuRmon history information IntervalRmon alarm information Command /info/rmon/eventRmon event information Link status information Command /info/port Port Tag Rmon Pvid Port informationVLANs Logical Port to GEA Port mapping Command /info/geaport Logical Port GEA Port0-based GEA UnitUplink Failure Detection Enabled LtM status Down Member Uplink Failure Detection informationCommand /info/dump Information dumpMenu information Ntp clearUfd clear Port Statistics Menu Authenticating 802.1x statisticsAuthSuccessesWhile Bridging statistics BackendNonNakResponsesFromSupplicant Ethernet statistics Dot3StatsSingleCollisionFrames Dot3StatsFCSErrorsDot3StatsInternalMacTransmitErrors Dot3StatsMultipleCollisionFramesInterface statistics Internet Protocol IP statistics Link statisticsPort Rmon statistics Layer 2 statistics FDB statisticsArp clear Lacp statisticsLayer 3 statistics Clrigmp 1- 4095 allIP statistics GEA Layer 3 statistics menuGEA Layer 3 statistics L3 bucket for An IP address DumpRoute statistics ARP statisticsDNS statistics Icmp statisticsTCP statistics UDP statistics Ospf statistics menu Command /stats/l3/ospfIgmp Multicast Group statistics Ospf stats MenuOspf global statistics Tx ls Updates Nbr changeTimers Kickoff Vrrp statisticsRIP statistics Command /stats/l3/ripManagement Processor statistics Packet statisticsAllocs 10ad41e8/10ad5790Access Control List ACL statistics menu CPU statisticsACL statistics Snmp statistics Only NTP statistics Statistics dump Command /stats/dumpUplink Failure Detection statistics Number of times LtM link in BlockingConfiguration Menu Viewing pending changes Saving the configurationViewing, applying, reverting, and saving changes Applying pending changesSystem configuration RemindersBannr 1-80 characters System host log configurationLine to end Host IP addressSecure Shell Server configuration Console disableenableLog featureall enabledisable Intrval Radius server configurationCommand /cfg/sys/radius Sshport TCP port numberTACACS+ server configuration Telnet enabledisable Port TCP port numberDlight disableenable NTP server configurationSystem Snmp configuration Command /cfg/sys/ssnmpSNMPv3 configuration Name 1-64 charactersCharacters User Security Model configuration V1v2 disableenableTree 1-32 characters SNMPv3 View configurationName 1-32 characters Mask 1-32 charactersUsmsnmpv1snmpv2 Level View-based Access Control Model configurationSNMPv3 Group configuration NoAuthNoPrivauthNoSNMPv3 Community Table configuration Usmsnmpv1snmpv2 UnameDel Deletes the vacmSecurityToGroup entry Cur Addr transport SNMPv3 Target Address Table configurationSNMPv3 Target Parameters Table configuration Address ip Port transportSNMPv3 Notify Table configuration Snmpv1snmpv2csnmp ModelSystem Access configuration Management Networks configurationUser Access Control configuration User ID configurationUseroperadmin Name Port configuration Https Access configurationAccess enabledisable Name 1-64 characters none Port link configuration Temporarily disabling a portLayer 2 configuration 802.1x configurationPort ACL/QoS configuration 802.1x Global configuration Mode forceUnauthautoforce-auth 802.1x Port configuration Reauth onoffMode rstpmstp RevPort parameter menu Common Internal Spanning Tree configurationBridge parameter menu 4095Cist bridge configuration Cist port configurationCost Spanning Tree configurationEdge disableenable Link autop2psharedBridge Spanning Tree configuration Spanning Tree port configuration Cur Display current port Spanning Tree parametersForwarding Database configuration Static FDB configurationFastfwd disableenable Clear mac MAC AddressVLAN 1-4095 Port port numberAll Trunk configurationMAC address Vlan port Add port numberIP Trunk Hash configuration Layer 2 IP Trunk Hash configurationLink Aggregation Control Protocol configuration Timeout shortlong Lacp Port configurationVlan configuration Mode offactivepassiveLayer 3 configuration Port numberList of port numbers IP interface configuration Addr IP addressMask IP subnet mask IP Static Route configuration Default Gateway configurationNetwork Filter configuration Address Resolution Protocol configurationIP Forwarding configuration Dirbr disableenableRoute Map configuration Ap AS number AS number ASLp 0-4294967294 none Metric 1-4294967294none IP Access List configurationAutonomous System Path configuration Action permitdenyRouting Information Protocol configuration RIP Interface configuration Add 1-32 1-32all Open Shortest Path First configurationRIP Route Redistribution configuration Remove 1-32 1-32allMd5key 1-255 characters Osfp Area Index configurationDefault 1-16777215 12none Redist fixedstaticripAreaid IP address Ospf Summary Range configurationAuth nonepasswordmd5 Type transitstubnssaKey key stringnone Ospf Interface configurationMask IP address mask Mdkey 1-255noneOspf Virtual Link configuration Key passwordNbr IP address Rem 1-32 1-32 ... all Ospf Host Entry configurationOspf Route Redistribution configuration Export 1-16777215 12noneIgmp configuration Ospf MD5 Key configurationFastlv 1-4095 disableenable Igmp snooping configurationAggr disableenable Srcip IP addressAdd port number 1-4095 Igmp static multicast router configurationIgmp filtering configuration FilterRange IP multicast address IP Igmp filtering port configurationIgmp filter definition Multicast addressBootstrap Protocol Relay configuration Domain Name System configurationVirtual Router Redundancy Protocol configuration Vrrp Virtual Router configurationPreem disableenable Vrs disableenable Vrrp Virtual Router Priority Tracking configurationVrrp Virtual Router Group configuration Ifs disableenableVrrp Virtual Router Group Priority Tracking configuration Vrrp Interface configuration Vrrp Tracking configurationPassw password Quality of Service configuration Access Control configurationQoS 802.1p configuration Action permitdenysetprio Access Control List configurationEgrport port number Stats edACL Ethernet Filter configuration ACL IP Version 4 Filter configurationACL TCP/UDP Filter configuration Sport 1-65535 port maskFlags value 0x0-0x3f Enable ed ACL Meter configurationACL Re-mark configuration CirACL Re-mark In-Profile configuration ACL Re-mark In-Profile Update User Priority configurationACL Re-mark Out-of-Profile configuration Remote Monitoring configuration ACL Packet Format configurationACL Group configuration Rmon history configuration Ifoid 1-127 charactersOwner 1-127 characters Descn 1-127 characters Rmon event configurationRmon alarm configuration Type nonelogtrapboth2147483647 Port mirroringRlimit -2147483647 to Flimit -2147483647 toAdd mirrored port inoutboth Uplink Failure Detection configurationPort-based port mirroring Rem mirrored portAddport port number Failure Detection Pair configurationLink to Monitor configuration Remport port numberDump Saving the active switch configurationLink to Disable configuration Addport port number Remport port numberRestoring the active switch configuration Command /cfg/gtcfg FTP/TFTP server filenameConfiguration# gtcfg FTP/TFTP server filename Operations Menu Operations-level port optionsReset Reauth Operations-level port 802.1x optionsOperations-level Vrrp options Updating the switch software image Downloading new software to the switchSelecting a software image to run AddressBoot Options# ptimg Uploading a software image from the switchSelecting a configuration block Boot Options# confBoot Options# reset Resetting the switchAccessing the Iscli Boot Options# curMaintenance Menu Flags new Nvram flags word as System maintenance optionsForwarding Database options 0xXXXXXXXXDebugging options ARP cache optionsIP Route Manipulation options Igmp Multicast Group optionsBroadcastmartian Igmp Snooping options Igmp Mrouter optionsUuencode flash dump FTP/TFTP system dump putClearing dump information Confirm dump and reboot y/n y Panic commandCommand /maint/panic Unscheduled system dumpsIndex

Related manuals

Manual 33 pages 57.51 Kb