HP NuDAQ I-9111DG/HR manual 9111DIChannel, 9111EDI

Page 50

cardNo:	The card number of PCI-9111 card initialized
DIData:	The value accessed from digital input port

@Return Code

ERR_NoError

5.7_9111_DI_Channel

@Description

This function is used to read data from digital input port. There are 16 digital input channels on PCI_9111. You can read each digital input channel by this function directly. As this function is performing, the digital input port is read and the value of the specified channel is stored in *data.

@ Syntax

C/C++ (DOS)

U16 _9111_DI_Channel (U16 cardNo, U16 di_ch_no , Boolean *di_data )

C/C++ (Windows 95)

U16 W_9111_DI_Channel (U16 cardNo, U16 di_ch_no , Boolean *di_data )

Visual Basic (Windows 95)

W_DAQ1210_DI_Channel (ByVal cardNo As Integer, ByVal di_ch_no As Integer, di_data As Byte) As Integer

@ Argument
cardNo:	The card number of PCI-9111 card initialized
di_ch_no:	The channel number to perform digital output, the value has
	to be set from 0 to 15.
di_data:	The value read from digital input channel, either 0 or 1.

@Return Code

ERR_NoError

ERR_InvalidDIChannel

5.8_9111_EDI

@Description

There are 4 extended digital input channels on PCI_9111. This function is used to read data from extended digital input ports. The retrieved data is stored in DIData and only the 4 LSBs of DIData is the valid input data.

@ Syntax

C/C++ (DOS)

U16 _9111_EDI (U16 cardNo, U16 *DIData)

C/C++ (Windows 95)

U16 W_9111_EDI (U16 cardNo, U16 *DIData)

40 ∙ C/C++ Library

Image 50

Contents NuDAQ Trademarks Getting service from Adlink QuestionsPage PCI PnP Registers Address Map Features Applications Specifications Software SupportingB l e o f C o n t e n t s Conversion Libraries Installation Programming GuideHardware Interrupt Clear Register Interrupt ControlTable of Contents ∙ What do you need VR Assignment Adjustment 9111utilHow to Use This Guide Page Features IntroductionSpecifications ApplicationsUnipolar 0~10V Bipolar -10V~+10V Software Supporting Programming LibraryDAQBenchTM ActiveX Controls PCIS-LVIEW LabVIEW DriverPCIS-VEE HP-VEE Driver DASYLabTM PROPCIS-ICL InControlTM Driver PCIS-OPC OPC ServerWhat You Have Installation∙ Software Installation Guide UnpackingPCI-9111s Layout PCB Layout of the PCI-9111Hardware Installation Outline Jumper Descriptions∙ CN 1 Digital Signal Input DI 0 ~ Device Installation for Windows SystemsConnectors Pin Assignment ∙ CN 2 Digital Signal Output do 0 ~ ∙ CN 3 Analog Input/Output, Extended I/O, Trigger SignalsConnect with ACLD-9137 Daughter Board ConnectionConnect with ACLD-8125 Connect with ACLD-9182Registers Format PCI PnP RegistersAddress Write Read I/O Address MapA/D Data Registers I/O AddressBit A/D Channel Control RegisterAddress Base + 0h Attribute read only Data Format Address Base + 6h Attribute write only Data Format BitAddress Base + 6h Attribute read only Data Format Bit A/D Input Signal Range Control RegisterA/D Channel Read Back Register Address Base + 8h Attribute write only Data Format BitAddress Base + 8h Attribute read only Data Format Bit A/D Trigger Mode Control RegisterA/D Range and Status Read back Register Address Base + 0Ah Attribute write only Data Format BitAddress Base + 0Ch Attribute write only Data Format Bit Mode DescriptionAddress Base + 0Eh Attribute write only Data Format Bit Address Base + 48h Attribute write only Data Format Bit 12 A/D Mode & Interrupt Control Read Back RegisterHardware Interrupt Clear Register Address Base + 0Ah Attribute read only Data Format BitAddress Base + 2h Attribute read only Data Format Address Base + 4h Attribute write only Data Format BitAddress Base + 4h Attribute read only Data Format Bit Address Base + 40h ~ Base + 46h 15 D/A Output RegisterAddress Base + 2h Attribute write only Data Format Bit Operation Theorem A/D Conversion1 A/D Conversion Procedure 2 A/D Signal Source ControlAnalog Input Signal Connection Signal Range 3 A/D Trigger Source Control4 A/D Data Transfer Modes External Trigger EITS=1, TPST=don‘t careFifo Half-Full Polling Pre-Trigger Control EOC Interrupt TransferTime 6 A/D Data Format FFFDual Interrupt System IRQ Level SettingInterrupt Control System Architecture Interrupt Source Control Extended Digital I/O PortD/A Conversion 44mV 88mVTimer/Counter Operation Introduction Digital Input and Output4 I/O Address Pacer Trigger SourcePre-Trigger Counter Libraries Installation ++ LibraryProgramming Guide Naming Convention Data Types++ DOS 9111Initial9111DO ++ Windows9111DOChannel 9111DI9111DIChannel 9111EDI9111EDO 10 9111EDOReadBack11 9111SetEDOFunction 12 9111DA 13 9111ADReadData14 9111ADReadDataRepeat 15 9111ADSetChannel16 9111ADGetChannel 17 9111ADSetRange Input Range Gain Gain Code18 9111ADGetRange 19 9111ADGetStatus20 9111ADSetMode 21 9111ADGetMode 22 9111INTSetReg24 9111ResetFIFO 23 9111INTGetReg25 9111ADSoftTrigger 26 9111Set825428 9111ADTimer 27 9111Get825429 9111CounterStart 30 9111CounterRead31 9111CounterStop 32 9111INTSourceControl 33 9111CLRIRQ 34 9111GetIRQChannel35 9111GetIRQStatus 36 9111ADFFHFPolling37 9111ADAquire 38 9111ADHRAquire39 9111ADINTStart 40 9111ADFFHFINTStart ++ Library ∙61 41 9111ADINTStatus 42 9111ADFFHFINTStatus43 9111ADFFHFINTRestart 44 9111ADINTStop Calibration What do you needFunctions of VRs A/D AdjustmentVR Assignment D/A Adjustment Unipolar Analog Output Bipolar Analog OutputRunning 9111util.exe Software Utility9111util System Configuration Calibration Functional Testing Function Testing Menu WindowIeeprom Product Warranty/Service