HP NuDAQ I-9111DG/HR manual Ieeprom

Page 82

Figure 8.2 A/D with Polling Test Window

7.2I_EEPROM

This file is used to enable or disable the interrupt of PCI-9111 board. This software is a text-driven program. Because the default interrupt on PCI-9111 board is “on”, users who doesn’t want to use interrupt function can use this utility to turn off the interrupt of their PCI-9111 board.

After finishing the DOS installation, you can execute the utility by typing as follows:

C> cd \ADLINK\DOS\9111\UTIL C> I_eeprom

At first, this program prompts you to input the card type —9111. After specifying the card type, this program shows the instructions to guide you to enable or disable the interrupt of your PCI-9111 board.

72 ∙ Software Utility

Image 82

Contents NuDAQ Trademarks Getting service from Adlink QuestionsPage B l e o f C o n t e n t s Features Applications Specifications Software SupportingPCI PnP Registers Address Map Conversion Libraries Installation Programming GuideHardware Interrupt Clear Register Interrupt ControlTable of Contents ∙ What do you need VR Assignment Adjustment 9111utilHow to Use This Guide Page Features IntroductionSpecifications ApplicationsUnipolar 0~10V Bipolar -10V~+10V Software Supporting Programming LibraryDAQBenchTM ActiveX Controls PCIS-LVIEW LabVIEW DriverPCIS-VEE HP-VEE Driver DASYLabTM PROPCIS-ICL InControlTM Driver PCIS-OPC OPC ServerWhat You Have Installation∙ Software Installation Guide UnpackingPCI-9111s Layout PCB Layout of the PCI-9111Hardware Installation Outline Jumper DescriptionsConnectors Pin Assignment Device Installation for Windows Systems∙ CN 1 Digital Signal Input DI 0 ~ ∙ CN 2 Digital Signal Output do 0 ~ ∙ CN 3 Analog Input/Output, Extended I/O, Trigger SignalsConnect with ACLD-9137 Daughter Board ConnectionConnect with ACLD-8125 Connect with ACLD-9182Registers Format PCI PnP RegistersAddress Write Read I/O Address MapA/D Data Registers I/O AddressBit A/D Channel Control RegisterAddress Base + 0h Attribute read only Data Format Address Base + 6h Attribute write only Data Format BitAddress Base + 6h Attribute read only Data Format Bit A/D Input Signal Range Control RegisterA/D Channel Read Back Register Address Base + 8h Attribute write only Data Format BitAddress Base + 8h Attribute read only Data Format Bit A/D Trigger Mode Control RegisterA/D Range and Status Read back Register Address Base + 0Ah Attribute write only Data Format BitAddress Base + 0Eh Attribute write only Data Format Bit Mode DescriptionAddress Base + 0Ch Attribute write only Data Format Bit Address Base + 48h Attribute write only Data Format Bit 12 A/D Mode & Interrupt Control Read Back RegisterHardware Interrupt Clear Register Address Base + 0Ah Attribute read only Data Format BitAddress Base + 4h Attribute read only Data Format Bit Address Base + 4h Attribute write only Data Format BitAddress Base + 2h Attribute read only Data Format Address Base + 2h Attribute write only Data Format Bit 15 D/A Output RegisterAddress Base + 40h ~ Base + 46h Operation Theorem A/D Conversion1 A/D Conversion Procedure 2 A/D Signal Source ControlAnalog Input Signal Connection Signal Range 3 A/D Trigger Source Control4 A/D Data Transfer Modes External Trigger EITS=1, TPST=don‘t careFifo Half-Full Polling Pre-Trigger Control EOC Interrupt TransferTime 6 A/D Data Format FFFInterrupt Control System Architecture IRQ Level SettingDual Interrupt System Interrupt Source Control Extended Digital I/O PortD/A Conversion 44mV 88mVTimer/Counter Operation Introduction Digital Input and OutputPre-Trigger Counter Pacer Trigger Source4 I/O Address Libraries Installation ++ LibraryProgramming Guide Naming Convention Data Types++ DOS 9111Initial9111DO ++ Windows9111DOChannel 9111DI9111DIChannel 9111EDI9111EDO 10 9111EDOReadBack11 9111SetEDOFunction 12 9111DA 13 9111ADReadData14 9111ADReadDataRepeat 15 9111ADSetChannel16 9111ADGetChannel 17 9111ADSetRange Input Range Gain Gain Code18 9111ADGetRange 19 9111ADGetStatus20 9111ADSetMode 21 9111ADGetMode 22 9111INTSetReg24 9111ResetFIFO 23 9111INTGetReg25 9111ADSoftTrigger 26 9111Set825428 9111ADTimer 27 9111Get825429 9111CounterStart 30 9111CounterRead31 9111CounterStop 32 9111INTSourceControl 33 9111CLRIRQ 34 9111GetIRQChannel35 9111GetIRQStatus 36 9111ADFFHFPolling37 9111ADAquire 38 9111ADHRAquire39 9111ADINTStart 40 9111ADFFHFINTStart ++ Library ∙61 41 9111ADINTStatus 42 9111ADFFHFINTStatus43 9111ADFFHFINTRestart 44 9111ADINTStop Calibration What do you needVR Assignment A/D AdjustmentFunctions of VRs D/A Adjustment Unipolar Analog Output Bipolar Analog Output9111util Software UtilityRunning 9111util.exe System Configuration Calibration Functional Testing Function Testing Menu WindowIeeprom Product Warranty/Service