GE 3800 230/208 Volt Electrical Supply HOW to Connect, If Using AN Electrical Subbase

Page 14

Installation Instructions

230/208 VOLT ELECTRICAL SUPPLY

HOW TO CONNECT

1Remove the room cabinet.

2Connect to electrical power.

3See the special instructions below for applicable supply voltages.

4Reinstall the room cabinet.

A power supply kit must be used to supply power to the Zoneline unit. The appropriate kit is determined by the voltage, the means of electrical connection and the amperage of the branch circuit.

Power supply kit

Connections of 208 or 230 volt circuits may be with a power supply kit or a junction box kit.

All wiring, including installation of the receptacle, must be in accordance with the NEC and local codes, ordinances and regulations. Local codes may require the use of an arc fault or leakage current detection device on the power cord. Be sure to select the correct cord for your installation.

Tandem

Perpendicular

Large Tandem

15 Amp.

20 Amp.

 

30 Amp.

230/208 volt receptacle configuration.

 

 

 

 

Branch Circuit and

 

Proper GE Power Cord

Unit Amperage Rating

 

 

with LCDI Device

 

 

 

 

 

 

 

15

 

 

RAK3153

 

 

 

 

 

 

 

20

 

 

RAK3203

 

 

 

 

 

 

 

30

 

 

RAK3303*

 

 

 

 

 

 

*Not approved for use on 7000 BTU models.

Power cords may include an arc fault interruption or a leakage current detection interruption device. A test and reset button is provided on the plug case or the inline case. The device should be tested on a periodic basis by first pressing the TEST button and then the RESET button. If the TEST button does not trip or if the RESET button will not stay engaged, discontinue use of the Zoneline and contact a qualified service technician.

Order Kit RAK4002A for 230/208 volt direct connection.

IF USING AN ELECTRICAL SUBBASE

230/208 volt models may be installed using one of the following electrical subbases:

Branch Circuit and

Proper GE

Unit Amperage Rating

Subbase Kit

 

 

 

15

RAK204D15P

 

 

 

20

RAK204D20P

 

 

 

30

RAK204D30P*

 

 

 

*Not approved for use on 7000 BTU models.

Electrical subbases provide an enclosure for direct connection or enclosed receptacles. The subbase kit includes the power cord.

The instructions provided with the selected subbase kit must be carefully followed. It is the responsibility of the installer to ensure the connection of components is done in accordance with these instructions and all electrical codes.

14

Image 14
Contents Air Conditioners Write the model and serial numbers here Model # Serial #Replacing an existing unit? Care and CleaningTroubleshooting Tips Consumer SupportAbout the controls on your Zoneline Troubleshooting Tips Consumer Support Air Direction Other features of your ZonelineCare and Cleaning To Remove the Room Cabinet Ventilation ControlAuxiliary Controls on your Zoneline Load Shedding Central Desk Control Care and Cleaning TipsRemote Thermostat-Class Freeze SentinelCare and Cleaning Temperature LimitingTroubleshooting Tips Consumer Support Heat SentinelTroubleshooting Consumer Support Auxiliary Controls-Terminal ConnectionsExternal Fan Obtained locally Care and Cleaning Remote ThermostatDoor Sensor Obtained locally Central Desk ControlCare and cleaning Safety Air Filters Instructions Operating InstructionsZoneline Components Before YOU BeginTools YOU will Need Read these instructions completely and carefullyReplacing AN Existing UNIT? New ducted installationExisting ducted installation Branch Circuit Proper GE 230/208 Volt Electrical Supply HOW to ConnectIf Using AN Electrical Subbase Volt Electrical Supply For Subbase InstallationFor Direct Connect Installation Remove Junction BOXReinstall Junction BOX Attach ConduitPower Connection Chart ConfigurationPrepare the Unit Installing the ZonelineInstall the Wall Case Exterior Grille Install the Unit Into the Wall Case Replace the Room CabinetOPTIONAL-DRAIN KIT Installation External DrainBefore you call for service… Problem Possible Causes What To DoOperation Air is not alwaysCool or hot during Air does not feelThings that are normal Normal Operating SoundsPage General Electric Company Consumer Product Ownership Registration GE Will Replace Zoneline WarrantyCleaning Warrantor General Electric Company. Louisville, KYConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio# de modèle # de série Transcrivez les numéros de modèle et de série iciSoutien au consommateur Conseils de dépannage Entretien et nettoyageRemise en place d’un appareil existant? FonctionnementLes commandes de votre Zoneline Autres caractéristiques de votre Zoneline Commandes auxiliaires sur votre Zoneline Entretien et nettoyage Garde de gel Délestage des charges Commande centraleThermostat à distance-Classe De dépannage Ventilateur toujours en marcheConseils de dépannage Limitation de températureGarde de chaleur Entretien et nettoyageCommandes auxiliaires-Bornes de raccordement Capteur de mouvement obtenu localementDe sécurité Ventilateur extérieur obtenu localement Commande centraleContacteur de porte obtenu localement Entretien et nettoyage Thermostat à distanceCarrosserie et boîtier côté chambre Entretien et nettoyageMesures de sécurité Fonctionnement Serpentin extérieurSécurité Fonctionnement Mise EN Garde Ne faitesFiltres à air Éléments Avant DE CommencerOutils Nécessaires DU ZonelineRemise EN Place D’UN Appareil EXISTANT? Nouvelle installation canaliséeInstallations canalisées existantes Alimentation Électrique 230/208 Volts Branchement Intensité en ampèresAlimentation Électrique DE 265 Volts Installation Avec SOUS-BASEInstallation Avec Branchement Direct Enlevez LA Boîte DE DérivationFixez LA Canalisation RÉ-INSTALLEZ LA Boîte DE DérivationRÉ-INSTALLEZ LE Couvercle DE LA Boîte DE Dérivation Tableau DE Contact Électrique De courantPréparation DE L’APPAREIL Installation DU ZonelineInstallation DU Boîtier Mural ET DE LA Grille Extérieure Installation DE L’APPAREIL Dans LE Boîtier Mural Remise EN Place DU Boîtier Côté ChambreEN OPTION-INSTALLATION DE LA Trousse DE Drainage Drainage extérieurPas en marche Avant d’appeler un réparateur…Problème Causes possibles Correctifs Autant qu’il devraitLe fonctionnement Des operations deRéchauffement ’air ne semble pasCes bruits sont normaux Bruits normaux de fonctionnementPage Page Page Ce qui n’est pas couvert Mesures de sécurité Fonctionnement Garantie ZonelineGE remplacera gratuitement Pour la période deService de réparations Soutien au consommateurAcondicionador Instrucciones de instalación¿Desea reemplazar una unidad ya instalada? Solucionar problemas Soporte al consumidorOperación Cuidado y limpieza Sólo la serie SeguridadControl de temperatura Control de modosControl de ventilación Solucionar problemas Consumidor Dirección del aireOtras características del Zoneline Cuidado y limpieza Cómo retirar el gabinete del ambienteControles auxiliares-Interruptores Solucionar problemas Calefacción-Ventilador inteligenteControles auxiliares del Zoneline Sólo calefacción eléctricaRegulación de consumo Control central Problemas Ventilador encendido constanteTermostato remoto-Clase Cuidado y limpieza Monitor de congelaciónRefuerzo de calor Sólo AZ3800 Limitación de temperaturaMonitor de calor Cuidado y limpiezaControles auxiliares-Conexiones terminales Sensor de movimientos disponible en forma localControl central Sensor de puerta disponible en forma localVentilador externo disponible en forma local Cuidado y limpieza Termostato remotoGabinete del ambiente y montante Cuidado y limpiezaSeguridad Operación Serpentinas externasFiltros de aire Solucionar problemas Soporte al consumidorPrecaución No utilice Componentes Antes DE ComenzarHerramientas Necesarias DEL Zoneline¿DESEA Cambiar UNA Unidad YA INSTALADA? Una nueva instalación con conductosSI Utiliza UNA SUB-BASE Eléctrica Suministro Eléctrico DE 265 Voltios Cómo Realizar LA ConexiónVuelva a Instalar LA Caja DE Conexiones Vuelva a Instalar LA Tapa DE LA Caja DE ConexionesTabla DE Conexiones Eléctricas @ 230/208 voltiosCómo Preparar LA Unidad Cómo Instalar EL ZonelineInstalación DEL Montante DE Pared Y LA Parrilla Exterior Cómo Instalar LA Unidad EN EL Montante DE Pared Opcional Instalación DE UN KIT DE Drenaje Drenaje externoSeguridad Operación Cuidado y limpieza Problema Causas posibles Qué hacerAntes de llamar para solicitar servicio… Sopote al consumidor Estos sonidos son normales Sonidos normales de operaciónNotas Notas Notas Limpieza Garantía de ZonelineGE reemplazará Por el período dePiezas y accesorios Soporte al consumidor Página Web de GE AppliancesSolicite una reparación Póngase en contacto con nosotros

3800 specifications

The GE 3800 is a sophisticated locomotive developed by General Electric, notable for its advanced technological features and robust design. As a member of the GE Dash 8 series, it was primarily built to cater to freight transport needs, delivering reliability and performance across various terrains.

One of the most noteworthy features of the GE 3800 is its powerful GE FDL-16 engine. This V16 four-stroke engine is known for its efficiency and durability, producing a significant amount of horsepower while maintaining low emissions. The engine's design allows for easy maintenance, which is essential for minimizing downtime in freight operations. With the capability of generating up to 3,800 horsepower, the GE 3800 can handle heavy loads while providing excellent tractive effort, making it ideal for freight-hauling.

Another critical technology integrated into the GE 3800 is its advanced electronic control system. The locomotive is equipped with a Digital Electronic Control (DEC) system that monitors and optimizes various functions, such as engine performance, braking, and traction control. This system enhances the locomotive's responsiveness, ensuring better handling of freight trains, especially in varied weather conditions.

The GE 3800 also features a robust braking system that includes dynamic and air brakes. The dynamic braking system allows for energy conservation, converting kinetic energy into electrical energy during deceleration, which can be reused when accelerating or transferred to the grid. This feature not only enhances safety but also contributes to lower operational costs.

In terms of design, the GE 3800 boasts a sturdy chassis that allows it to withstand the rigors of heavy-duty freight transport. Its aerodynamic profile reduces drag, improving fuel efficiency during operations. The locomotive is equipped with advanced wheel and axle assemblies that enhance stability and reduce wear and tear, prolonging the lifespan of the train’s components.

Safety is a primary concern in locomotive design, and the GE 3800 includes numerous safety features such as redundant systems, crash-worthy designs, and advanced signaling and communication technologies. These elements ensure that the locomotive can operate safely in busy rail networks.

Overall, the GE 3800 is a blend of power, efficiency, and modern technology, making it a preferred choice for freight operators around the world. Its combination of a powerful engine, advanced electronic control systems, robust construction, and safety features ensures that it remains a significant player in the rail transport industry.