Omega Speaker Systems iSE-TC manual DIP Switches, DIP Switch Location

Page 10

2.2 DIP Switches

The iSE is shipped with all DIP switches in "OFF" position.

DIP Switch Usage

1) N/C - not used

2) To change to default factory settings

3) To enable/disable DHCP

4) N/C - not used

Figure 2.3 DIP Switch Location

To set the iSE to factory default settings, slide DIP switch #2 to ON position. Power the iSE on and wait about 10 seconds until the iSE fully boots up. Set the DIP switch #2 back to OFF position (it does not matter if the iSE is powered ON or OFF, just make sure that the DIP switch is set to OFF, otherwise, every time the unit is power-cycled the factory settings will take over.

To enable the DHCP, besides using DIP switch #3, set the iSE’s IP address to 0.0.0.0. An iSE with IP address of 0.0.0.0 will request an IP address, gateway address, and subnet mask from the DHCP server over the Ethernet

6

Image 10

Contents User’s Guide Page Dhcp DNS List of Figures ISE and iLD Big Display on the Ethernet NetworkFeatures Part Introduction Page ISE and iLD Big Display on the Ethernet Network Part 2 Hardware Wall MountingDIP Switches DIP Switch LocationParts of the iSE Unit Parts of iSE UnitDisassembly Instruction Opening the UnitCrossover Cable Wiring Relay and I/O Contact Wiring ConnectionsNetwork Communication Interfaces 1 10Base-T RJ-45 Pinout Running on Battery Power Battery and S5 Jumper LocationFlash Memory Format Data Record TestPart Network Configuration 3.1 Network ProtocolsEthernet MAC Address Subnet Mask DhcpDNS SectionPort Number Default IP AddressExample C\Telnet 192.168.1.200 Testing the Connection Part OperationsIConnect Software ISERVER Home Setting a New IP Address over the Network Access ControlPrompted for a password, as shown in Figure Setup and Operation Using the iSE WebLogin and Administrator Passwords Read Sensor Java Runtime Environment 1.4 Setup instructions Read SensorAccessing iSE units using the internet Java Runtime Environment 1.5 5.0 Setup instructionsDiagnostics Adjustable Chart Fla sh ArchiveRetrieving Data from Flash OptionDhcp can be enabled by setting the dip switch number #2 RTC is set, and recording is in progress Configuration#1 RTC is not set and Flash Card is empty #4 RTC is not set and the Flash Card is not emptyReal Time Clock Flash Recording SettingsRemote Access Tunneling MegaBytes Flash Card 22 Kbytes Used SpaceConfiguration/Device Setup Temperature 1 and TemperatureInput 2 Status Unlatch, Latch, Clear Latch, Chart SP Flash RecordingConfiguration Configuration Input Contact Closure Terminal ServerConfiguration Remote Access 12 Sensor Parameters Temperature Sensor ParametersTA71.34F TA72.48F TD-1.19F TA71.34FTA72.48FTD-1.19FTelnet Setup HTTPget ProgramHTTPget using Port Srhc SrtcSrtf SrhfArp -s 192.168.1.200 00-03-34-00-06-b6 HTTPget and ARP to setup Device IP AddressWhere 15 ARP Commands and Responses ARP ProtocolILog Software 16 iLog Software Logging DataInstallation Mail Notifier SoftwareEmail Setup OptionsDevice Setting and Configuration Device setup requires 19 iSE Mail Notifier Device SettingPart Specifications Sensor Specifications Thermocouple InputEnvironmental PowerInterfaces PackagingNetwork Interface Part Approvals Information CE Approval Measurement CategoryAppendix Aglossary Appendix BIP Address Or Dotted Notation Appendix CIP NetmaskAddress Class Mask Binary Value Mask Decimal Value Mask Dotted Notation Mask Binary Mask BitsDec Binary Appendix D Hex Ascii Chart Dec BinaryAscii Char No Parity No parityDec Hex Ctrl Key Ascii Control Codes Definition Appendix D Ascii Chart ContinuationChar Equiv Appendix E ILog Error Messages Error # Description Page Page WARRANTY/DISCLAIMER Shop on line at omega.com