Omega Speaker Systems iSE-TC manual Dhcp, Dns, Subnet Mask, Section, IP Address

Page 17

3.3 DHCP

DHCP, Dynamic Host Configuration Protocol enables individual computers or devices to extract their IP configurations from a server (DHCP server). If the DHCP is enabled on your iSE, as soon as the iSE is connected to the network, there is an exchange of information between DHCP server and the iSE. During this process the IP address, the Gateway address, and the Subnet Mask will be assigned to the iSE by the DHCP server. Note that the DHCP server must be configured correctly to do such assignment.

If fixed or static IP address is desired, the DHCP must be disabled. The iSE is shipped with DHCP disabled (factory default). The DHCP can be enabled by setting the DIP switch # 3 to the “ON” position (refer to Figure 3.2).

DIP switch # 3 shown in “ON” position

OFF4 3 2 1

ON

3.4 DNS

Figure 3.2 DIP Switch on the Bottom Side of iSE

 

DNS, Domain Name System enables individual computers and devices to be recognized

over a network based on a specific name instead of an IP address. For example, instead

of having to use http://192.168.1.200 (IP address), you would use only http://eis03ec or

any eight character name stored as Host Name under the Access Control page in the

iSE Home Page. The default DNS name for an iSE is "eis" followed by the last four

digits of the MAC address of that particular iSE.

1. It is very important to communicate with the network administrator in order to

 

understand the DHCP and its existing configurations on the host server,

 

before enabling the DHCP on the iSE.

2. The iSE is shipped with a default static IP address of

 

192.168.1.200 and Subnet Mask of 255.255.255.0.

3. On Novell networks or Windows 2000 Server where the DCHP is an updated

 

function of DNS, this feature may be beneficial since a particular name can

 

be assigned eliminating the need for the IP address, as described in

 

Section 3.4.

3.5 IP Address

Every active device connected to the TCP/IP network must have a unique IP address.

This IP address is used to build a connection to the iSE. Every computer using TCP/IP

should have a unique 32-bit address. It is divided into two portions, the network ID and

the host ID. For instance, every computer on the same network uses the same network

ID. At the same time, all of them have a different host ID. For more details about the IP

address see Appendix B.

13

Image 17
Contents User’s Guide Page Dhcp DNS ISE and iLD Big Display on the Ethernet Network List of FiguresFeatures Part Introduction Page ISE and iLD Big Display on the Ethernet Network Wall Mounting Part 2 HardwareDIP Switch Location DIP SwitchesParts of iSE Unit Parts of the iSE UnitOpening the Unit Disassembly InstructionNetwork Communication Interfaces 1 10Base-T RJ-45 Pinout Relay and I/O Contact Wiring ConnectionsCrossover Cable Wiring Battery and S5 Jumper Location Running on Battery PowerData Record Test Flash Memory FormatEthernet MAC Address Network Configuration 3.1 Network ProtocolsPart DNS DhcpSubnet Mask SectionExample C\Telnet 192.168.1.200 Default IP AddressPort Number Part Operations Testing the ConnectionIConnect Software ISERVER Home Access Control Setting a New IP Address over the NetworkLogin and Administrator Passwords Setup and Operation Using the iSE WebPrompted for a password, as shown in Figure Read Sensor Read Sensor Java Runtime Environment 1.4 Setup instructionsDiagnostics Java Runtime Environment 1.5 5.0 Setup instructionsAccessing iSE units using the internet Fla sh Archive Adjustable ChartOption Retrieving Data from FlashDhcp can be enabled by setting the dip switch number #1 RTC is not set and Flash Card is empty Configuration#2 RTC is set, and recording is in progress #4 RTC is not set and the Flash Card is not emptyRemote Access Tunneling Flash Recording SettingsReal Time Clock MegaBytes Flash Card 22 Kbytes Used SpaceTemperature 1 and Temperature Configuration/Device SetupFlash Recording Input 2 Status Unlatch, Latch, Clear Latch, Chart SPConfiguration Terminal Server Configuration Input Contact ClosureConfiguration Remote Access Sensor Parameters 12 Sensor Parameters TemperatureTA71.34FTA72.48FTD-1.19F TA71.34F TA72.48F TD-1.19FHTTPget Program Telnet SetupHTTPget using Port Srtf SrtcSrhc SrhfWhere HTTPget and ARP to setup Device IP AddressArp -s 192.168.1.200 00-03-34-00-06-b6 ARP Protocol 15 ARP Commands and Responses16 iLog Software Logging Data ILog SoftwareMail Notifier Software InstallationOptions Email Setup19 iSE Mail Notifier Device Setting Device Setting and Configuration Device setup requiresThermocouple Input Part Specifications Sensor SpecificationsInterfaces PowerEnvironmental PackagingNetwork Interface Measurement Category Part Approvals Information CE ApprovalAppendix Aglossary Appendix BIP Address Address Class Mask Binary Value Mask Decimal Value Appendix CIP NetmaskOr Dotted Notation Mask Dotted Notation Mask Binary Mask BitsAscii Appendix D Hex Ascii Chart Dec BinaryDec Binary Char No Parity No parityChar Equiv Appendix D Ascii Chart ContinuationDec Hex Ctrl Key Ascii Control Codes Definition Appendix E ILog Error Messages Error # Description Page Page WARRANTY/DISCLAIMER Shop on line at omega.com