Omega Speaker Systems iSE-TC manual Part Approvals Information CE Approval, Measurement Category

Page 50

PART 7

 

 

 

APPROVALS INFORMATION

 

7.1 CE APPROVAL

 

 

 

 

This product conforms to the EMC directive 89/336/EEC amended by 93/68/EEC,

 

 

and with the European Low Voltage Directive 72/23/EEC.

 

 

Electrical Safety EN61010-1:2001

 

Safety requirements for electrical equipment for measurement, control and laboratory.

Basic Insulation

 

 

Pollution Degree 2

 

 

Dielectric withstand Test per 1 min

1500Vac

•

Input Power to Ethernet Output:

•

Input Power to Relays:

1500Vac

•

Ethernet Output to Relays:

1500Vac

Measurement Category I

 

Category I are measurements performed on circuits not directly connected to the Mains

Supply (power). Unit measures Temperature.

 

Transients Overvoltage Surge (1.2/50uS Pulse)

•

Input Power:

500V Transients Overvoltage

•

Ethernet:

1500V Transients Overvoltage

Note:

The ac/dc power adaptor must have Safety Qualified Agency Approvals

 

 

for CE with Double Insulation rating.

 

 

 

The ac/dc power adaptor is 9Vdc.

 

 

 

The minimum output current rating is 500mA.

EMC EN61000-6-1:2001 (Immunity) and EN61000-6-3:2001 (Emmissions)

Immunity requirements for residential, commercial and light-industrial environments

•

EMC Emissions

Table 1, Class B

 

•

EMC Immunity

Table 1: Enclosure

 

 

 

 

Table 2: Signal Lines Ports

 

 

 

Table 3: Dc input/Dc output Ports

EMC EN61326:1997 + and A1:1998 + A2:2001

 

Immunity and Emissions requirements for electrical equipment for measurement, control

and laboratory.

Table 4, Class B of EN61326

•

EMC Emissions

•

EMC Immunity

Table 1 of EN61326

 

Note:

I/O lines / sensor cables require shielded cables and these cables must be located

 

 

on conductive cable trays or in conduits.

Refer to the EMC and Safety installation considerations (Guidelines) of this manual for additional information.

7.2FCC

This device complies with Part 15, Subpart B, Class B of the FCC rules.

46

Page 49 Page 51
Image 50
Page 49 Page 51
Contents User’s Guide Page Dhcp DNS List of Figures ISE and iLD Big Display on the Ethernet NetworkFeatures Part Introduction Page ISE and iLD Big Display on the Ethernet Network Part 2 Hardware Wall MountingDIP Switches DIP Switch LocationParts of the iSE Unit Parts of iSE UnitDisassembly Instruction Opening the UnitNetwork Communication Interfaces 1 10Base-T RJ-45 Pinout Relay and I/O Contact Wiring ConnectionsCrossover Cable Wiring Running on Battery Power Battery and S5 Jumper LocationFlash Memory Format Data Record TestEthernet MAC Address Network Configuration 3.1 Network ProtocolsPart Subnet Mask DhcpDNS SectionExample C\Telnet 192.168.1.200 Default IP AddressPort Number Testing the Connection Part OperationsIConnect Software ISERVER Home Setting a New IP Address over the Network Access ControlLogin and Administrator Passwords Setup and Operation Using the iSE WebPrompted for a password, as shown in Figure Read Sensor Java Runtime Environment 1.4 Setup instructions Read SensorDiagnostics Java Runtime Environment 1.5 5.0 Setup instructionsAccessing iSE units using the internet Adjustable Chart Fla sh ArchiveRetrieving Data from Flash OptionDhcp can be enabled by setting the dip switch number #2 RTC is set, and recording is in progress Configuration#1 RTC is not set and Flash Card is empty #4 RTC is not set and the Flash Card is not emptyReal Time Clock Flash Recording SettingsRemote Access Tunneling MegaBytes Flash Card 22 Kbytes Used SpaceConfiguration/Device Setup Temperature 1 and TemperatureInput 2 Status Unlatch, Latch, Clear Latch, Chart SP Flash RecordingConfiguration Configuration Input Contact Closure Terminal ServerConfiguration Remote Access 12 Sensor Parameters Temperature Sensor ParametersTA71.34F TA72.48F TD-1.19F TA71.34FTA72.48FTD-1.19FTelnet Setup HTTPget ProgramHTTPget using Port Srhc SrtcSrtf SrhfWhere HTTPget and ARP to setup Device IP AddressArp -s 192.168.1.200 00-03-34-00-06-b6 15 ARP Commands and Responses ARP ProtocolILog Software 16 iLog Software Logging DataInstallation Mail Notifier SoftwareEmail Setup OptionsDevice Setting and Configuration Device setup requires 19 iSE Mail Notifier Device SettingPart Specifications Sensor Specifications Thermocouple InputEnvironmental PowerInterfaces PackagingNetwork Interface Part Approvals Information CE Approval Measurement CategoryAppendix Aglossary Appendix BIP Address Or Dotted Notation Appendix CIP NetmaskAddress Class Mask Binary Value Mask Decimal Value Mask Dotted Notation Mask Binary Mask BitsDec Binary Appendix D Hex Ascii Chart Dec BinaryAscii Char No Parity No parityChar Equiv Appendix D Ascii Chart ContinuationDec Hex Ctrl Key Ascii Control Codes Definition Appendix E ILog Error Messages Error # Description Page Page WARRANTY/DISCLAIMER Shop on line at omega.com
Top Page Image Contents