Omega Speaker Systems iSE-TC manual Flash Memory Format, Data Record Test

Page 15

2.9 Flash Memory Format

A 2 Meg flash memory card is included with your product. This memory card is already formatted; however, the following procedure describes how to format your memory card. Once the memory card is formatted, all the data that had previously been

recorded will be replaced by simulated test data (see Figure 2.10).

1) Unplug the AC adaptor from the unit.

2) Hold down the ºC/ºF button and connect the AC adaptor back into the unit. Release the ºC/ºF button.

3) You will see the following message appear on the LCD: *ºWAITº* *FLASH*.

4) Wait for about 60 seconds and a new message should appear: *ºWAITº* *OKAY*.

5) Press the ºC/ºF button once and this message will appear: DATA-RECORD-TEST.

6) Press the TIME button and this message will appear: DATA RECORD TEST -

DATA RECORD TEST.

8) Again, press the ºC/ºF button, the firmware version will appear, followed by *OKAY*.

9) Unplug the AC adaptor and plug it back in. The flash memory card is now formatted. To verify whether the formatting was completed correctly, you should be able to see the following graph on the WEB server’s “Chart” page.

Figure 2.10 Chart of Simulated Data

11

Image 15

Contents User’s Guide Page Dhcp DNS ISE and iLD Big Display on the Ethernet Network List of FiguresFeatures Part Introduction Page ISE and iLD Big Display on the Ethernet Network Wall Mounting Part 2 HardwareDIP Switch Location DIP SwitchesParts of iSE Unit Parts of the iSE UnitOpening the Unit Disassembly InstructionRelay and I/O Contact Wiring Connections Crossover Cable WiringNetwork Communication Interfaces 1 10Base-T RJ-45 Pinout Battery and S5 Jumper Location Running on Battery PowerData Record Test Flash Memory FormatNetwork Configuration 3.1 Network Protocols PartEthernet MAC Address Section DhcpDNS Subnet MaskDefault IP Address Port NumberExample C\Telnet 192.168.1.200 Part Operations Testing the ConnectionIConnect Software ISERVER Home Access Control Setting a New IP Address over the NetworkSetup and Operation Using the iSE Web Prompted for a password, as shown in FigureLogin and Administrator Passwords Read Sensor Read Sensor Java Runtime Environment 1.4 Setup instructionsJava Runtime Environment 1.5 5.0 Setup instructions Accessing iSE units using the internetDiagnostics Fla sh Archive Adjustable ChartOption Retrieving Data from FlashDhcp can be enabled by setting the dip switch number #4 RTC is not set and the Flash Card is not empty Configuration#1 RTC is not set and Flash Card is empty #2 RTC is set, and recording is in progressMegaBytes Flash Card 22 Kbytes Used Space Flash Recording SettingsRemote Access Tunneling Real Time ClockTemperature 1 and Temperature Configuration/Device SetupFlash Recording Input 2 Status Unlatch, Latch, Clear Latch, Chart SPConfiguration Terminal Server Configuration Input Contact ClosureConfiguration Remote Access Sensor Parameters 12 Sensor Parameters TemperatureTA71.34FTA72.48FTD-1.19F TA71.34F TA72.48F TD-1.19FHTTPget Program Telnet SetupHTTPget using Port Srhf SrtcSrtf SrhcHTTPget and ARP to setup Device IP Address Arp -s 192.168.1.200 00-03-34-00-06-b6Where ARP Protocol 15 ARP Commands and Responses16 iLog Software Logging Data ILog SoftwareMail Notifier Software InstallationOptions Email Setup19 iSE Mail Notifier Device Setting Device Setting and Configuration Device setup requiresThermocouple Input Part Specifications Sensor SpecificationsPackaging PowerInterfaces EnvironmentalNetwork Interface Measurement Category Part Approvals Information CE ApprovalAppendix Aglossary Appendix BIP Address Mask Dotted Notation Mask Binary Mask Bits Appendix CIP NetmaskAddress Class Mask Binary Value Mask Decimal Value Or Dotted NotationChar No Parity No parity Appendix D Hex Ascii Chart Dec BinaryAscii Dec BinaryAppendix D Ascii Chart Continuation Dec Hex Ctrl Key Ascii Control Codes DefinitionChar Equiv Appendix E ILog Error Messages Error # Description Page Page WARRANTY/DISCLAIMER Shop on line at omega.com