Omega Speaker Systems iSE-TC manual IConnect Software

Page 20

4.1 iConnect Software

The iSE may also be assigned an IP Address by using the iConnect software. a) Download the iConnect software from the website listed in this manual.

b) Install iConnect software on a networked PC. This software is compatible with Windows 95, 98, NT, 2000, and XP.

c) Use iConnect to assign an IP address to the iSE and access its web pages for configuration. You can also use any standard web browser to access the iSE’s web pages. Consult with your IT department for obtaining an IP address.

Figure 4.2 Assigning an IP Address using iConnect 1) Place the IP address in this box.

2) Take the MAC address from the label attached to the bottom of the iSE and place it in this box.

3) Click here to send the above IP address to the iSE.

4) After the IP address is assigned to the iSE, click here to access it’s web pages.

5) Click here to Ping the iSE whose IP address is shown in the IP address box.

6) Click here to find all the iSE’s on your network .

7) The IP addresses for the iSE’s found by the iConnect will be listed here.

8) These fields indicate the IP address and the subnet mask of the PC on which the iConnect is running.

16

Image 20

Contents User’s Guide Page Dhcp DNS List of Figures ISE and iLD Big Display on the Ethernet NetworkFeatures Part Introduction Page ISE and iLD Big Display on the Ethernet Network Part 2 Hardware Wall MountingDIP Switches DIP Switch LocationParts of the iSE Unit Parts of iSE UnitDisassembly Instruction Opening the UnitNetwork Communication Interfaces 1 10Base-T RJ-45 Pinout Relay and I/O Contact Wiring ConnectionsCrossover Cable Wiring Running on Battery Power Battery and S5 Jumper LocationFlash Memory Format Data Record TestEthernet MAC Address Network Configuration 3.1 Network ProtocolsPart Dhcp DNSSubnet Mask SectionExample C\Telnet 192.168.1.200 Default IP AddressPort Number Testing the Connection Part OperationsIConnect Software ISERVER Home Setting a New IP Address over the Network Access ControlLogin and Administrator Passwords Setup and Operation Using the iSE WebPrompted for a password, as shown in Figure Read Sensor Java Runtime Environment 1.4 Setup instructions Read SensorDiagnostics Java Runtime Environment 1.5 5.0 Setup instructionsAccessing iSE units using the internet Adjustable Chart Fla sh ArchiveRetrieving Data from Flash OptionDhcp can be enabled by setting the dip switch number Configuration #1 RTC is not set and Flash Card is empty#2 RTC is set, and recording is in progress #4 RTC is not set and the Flash Card is not emptyFlash Recording Settings Remote Access TunnelingReal Time Clock MegaBytes Flash Card 22 Kbytes Used SpaceConfiguration/Device Setup Temperature 1 and TemperatureInput 2 Status Unlatch, Latch, Clear Latch, Chart SP Flash RecordingConfiguration Configuration Input Contact Closure Terminal ServerConfiguration Remote Access 12 Sensor Parameters Temperature Sensor ParametersTA71.34F TA72.48F TD-1.19F TA71.34FTA72.48FTD-1.19FTelnet Setup HTTPget ProgramHTTPget using Port Srtc SrtfSrhc SrhfWhere HTTPget and ARP to setup Device IP AddressArp -s 192.168.1.200 00-03-34-00-06-b6 15 ARP Commands and Responses ARP ProtocolILog Software 16 iLog Software Logging DataInstallation Mail Notifier SoftwareEmail Setup OptionsDevice Setting and Configuration Device setup requires 19 iSE Mail Notifier Device SettingPart Specifications Sensor Specifications Thermocouple InputPower InterfacesEnvironmental PackagingNetwork Interface Part Approvals Information CE Approval Measurement CategoryAppendix Aglossary Appendix BIP Address Appendix CIP Netmask Address Class Mask Binary Value Mask Decimal ValueOr Dotted Notation Mask Dotted Notation Mask Binary Mask BitsAppendix D Hex Ascii Chart Dec Binary AsciiDec Binary Char No Parity No parityChar Equiv Appendix D Ascii Chart ContinuationDec Hex Ctrl Key Ascii Control Codes Definition Appendix E ILog Error Messages Error # Description Page Page WARRANTY/DISCLAIMER Shop on line at omega.com