Omega Speaker Systems iSE-TC manual HTTPget and ARP to setup Device IP Address, Where

Page 41

4.5.2 HTTPget and ARP to setup Device IP Address

Use the iConnect software, which may be downloaded from our website, to do these IP changes whenever possible.

Use ARP first to assign the mac address to a static IP address in computer arp table by this command:

arp –s 192.168.1.200 00-03-34-00-06-b6

Then use the following command to assign new IP to the device: httpget –r–S "00000000" 192.168.1.200:1

where:

“00000000” is admin. password. If the password is wrong, the unit will ignore the new IP. If the new IP is taken, you will get the message " New IP is Assigned" after the HTTPget command. The device will reset automatically. (TX and RX led is on for 2 seconds).

“192.168.1.200” is an example of an IP adress. It is replaced with an IP address suitable for your network

“00-03-34-00-06-b6” is replaced with your iSE product MAC address.

37

Image 41

Contents User’s Guide Page Dhcp DNS ISE and iLD Big Display on the Ethernet Network List of FiguresFeatures Part Introduction Page ISE and iLD Big Display on the Ethernet Network Wall Mounting Part 2 HardwareDIP Switch Location DIP SwitchesParts of iSE Unit Parts of the iSE UnitOpening the Unit Disassembly InstructionNetwork Communication Interfaces 1 10Base-T RJ-45 Pinout Relay and I/O Contact Wiring ConnectionsCrossover Cable Wiring Battery and S5 Jumper Location Running on Battery PowerData Record Test Flash Memory FormatEthernet MAC Address Network Configuration 3.1 Network ProtocolsPart DNS DhcpSubnet Mask SectionExample C\Telnet 192.168.1.200 Default IP AddressPort Number Part Operations Testing the ConnectionIConnect Software ISERVER Home Access Control Setting a New IP Address over the NetworkLogin and Administrator Passwords Setup and Operation Using the iSE WebPrompted for a password, as shown in Figure Read Sensor Read Sensor Java Runtime Environment 1.4 Setup instructionsDiagnostics Java Runtime Environment 1.5 5.0 Setup instructionsAccessing iSE units using the internet Fla sh Archive Adjustable ChartOption Retrieving Data from FlashDhcp can be enabled by setting the dip switch number #1 RTC is not set and Flash Card is empty Configuration#2 RTC is set, and recording is in progress #4 RTC is not set and the Flash Card is not emptyRemote Access Tunneling Flash Recording SettingsReal Time Clock MegaBytes Flash Card 22 Kbytes Used SpaceTemperature 1 and Temperature Configuration/Device SetupFlash Recording Input 2 Status Unlatch, Latch, Clear Latch, Chart SPConfiguration Terminal Server Configuration Input Contact ClosureConfiguration Remote Access Sensor Parameters 12 Sensor Parameters TemperatureTA71.34FTA72.48FTD-1.19F TA71.34F TA72.48F TD-1.19FHTTPget Program Telnet SetupHTTPget using Port Srtf SrtcSrhc SrhfWhere HTTPget and ARP to setup Device IP AddressArp -s 192.168.1.200 00-03-34-00-06-b6 ARP Protocol 15 ARP Commands and Responses16 iLog Software Logging Data ILog SoftwareMail Notifier Software InstallationOptions Email Setup19 iSE Mail Notifier Device Setting Device Setting and Configuration Device setup requiresThermocouple Input Part Specifications Sensor SpecificationsInterfaces PowerEnvironmental PackagingNetwork Interface Measurement Category Part Approvals Information CE ApprovalAppendix Aglossary Appendix BIP Address Address Class Mask Binary Value Mask Decimal Value Appendix CIP NetmaskOr Dotted Notation Mask Dotted Notation Mask Binary Mask BitsAscii Appendix D Hex Ascii Chart Dec BinaryDec Binary Char No Parity No parityChar Equiv Appendix D Ascii Chart ContinuationDec Hex Ctrl Key Ascii Control Codes Definition Appendix E ILog Error Messages Error # Description Page Page WARRANTY/DISCLAIMER Shop on line at omega.com