Omega Speaker Systems iSE-TC manual Part, Network Configuration 3.1 Network Protocols

Page 16

PART 3

NETWORK CONFIGURATION 3.1 Network Protocols

The iSE can be connected to the network using standard TCP/IP protocols. It also supports ARP, HTTP (WEB server), DHCP, DNS and Telnet protocols.

3.2 Ethernet (MAC) Address

MAC (Media Access Control) address is your computer's unique hardware number. When you're connected to the LAN from your computer, a correspondence table relates your IP address to your computer's physical (MAC) address. The MAC address can be found on a label attached to your device and contains 6 bytes (12 characters) of hexadecimal numbers XX:XX:XX:XX:XX:XX hex

For example: 0A:0C:3D:0B:0A:0B

Remove the small label with the default IP address and there will be room to put your IP address. See Figure 3.1

 

1

JTAG CONNECTOR

4 N/C 3 DHCP 2 DEFAULT 1 N/C

OFF

 

 

ON

SCREW FOR

 

GROUNDING UNIT

 

REMOVE DEFAULT IP ADDRESS LABEL AND PUT NEW CUSTOMER'S IP ADDRESS

iSE’S VERSION #

Figure 3.1 Labeling

MICRO- PROCESSOR VERSION #

MAC ADDRESS LABEL IN HEX CODE

12

Image 16
Contents User’s Guide Page Dhcp DNS List of Figures ISE and iLD Big Display on the Ethernet NetworkFeatures Part Introduction Page ISE and iLD Big Display on the Ethernet Network Part 2 Hardware Wall MountingDIP Switches DIP Switch LocationParts of the iSE Unit Parts of iSE UnitDisassembly Instruction Opening the UnitCrossover Cable Wiring Relay and I/O Contact Wiring ConnectionsNetwork Communication Interfaces 1 10Base-T RJ-45 Pinout Running on Battery Power Battery and S5 Jumper LocationFlash Memory Format Data Record TestPart Network Configuration 3.1 Network ProtocolsEthernet MAC Address Dhcp DNSSubnet Mask SectionPort Number Default IP AddressExample C\Telnet 192.168.1.200 Testing the Connection Part OperationsIConnect Software ISERVER Home Setting a New IP Address over the Network Access ControlPrompted for a password, as shown in Figure Setup and Operation Using the iSE WebLogin and Administrator Passwords Read Sensor Java Runtime Environment 1.4 Setup instructions Read SensorAccessing iSE units using the internet Java Runtime Environment 1.5 5.0 Setup instructionsDiagnostics Adjustable Chart Fla sh ArchiveRetrieving Data from Flash OptionDhcp can be enabled by setting the dip switch number Configuration #1 RTC is not set and Flash Card is empty#2 RTC is set, and recording is in progress #4 RTC is not set and the Flash Card is not emptyFlash Recording Settings Remote Access TunnelingReal Time Clock MegaBytes Flash Card 22 Kbytes Used SpaceConfiguration/Device Setup Temperature 1 and TemperatureInput 2 Status Unlatch, Latch, Clear Latch, Chart SP Flash RecordingConfiguration Configuration Input Contact Closure Terminal ServerConfiguration Remote Access 12 Sensor Parameters Temperature Sensor ParametersTA71.34F TA72.48F TD-1.19F TA71.34FTA72.48FTD-1.19FTelnet Setup HTTPget ProgramHTTPget using Port Srtc SrtfSrhc SrhfArp -s 192.168.1.200 00-03-34-00-06-b6 HTTPget and ARP to setup Device IP AddressWhere 15 ARP Commands and Responses ARP ProtocolILog Software 16 iLog Software Logging DataInstallation Mail Notifier SoftwareEmail Setup OptionsDevice Setting and Configuration Device setup requires 19 iSE Mail Notifier Device SettingPart Specifications Sensor Specifications Thermocouple InputPower InterfacesEnvironmental PackagingNetwork Interface Part Approvals Information CE Approval Measurement CategoryAppendix Aglossary Appendix BIP Address Appendix CIP Netmask Address Class Mask Binary Value Mask Decimal ValueOr Dotted Notation Mask Dotted Notation Mask Binary Mask BitsAppendix D Hex Ascii Chart Dec Binary AsciiDec Binary Char No Parity No parityDec Hex Ctrl Key Ascii Control Codes Definition Appendix D Ascii Chart ContinuationChar Equiv Appendix E ILog Error Messages Error # Description Page Page WARRANTY/DISCLAIMER Shop on line at omega.com