Omega Speaker Systems iSE-TC manual Parts of the iSE Unit, Parts of iSE Unit

Page 11

2.3 Parts of the iSE Unit

				Figure 2.4 Parts of the iSE Unit
				Figure 2.4 Parts of the iSE Unit
	Table 2.1 Parts of iSE Unit
	ETHERNET			RJ45 interface for 10BASE-T connection.
	ETHERNET			RJ45 interface for 10BASE-T connection.
	RESET			Button: Used for power reseting the iSE.
	ACTIVITY			LED (Red) Blinking: Indicates network activities (receiving or sending packets).
	NET LINK			LED (Green) Solid: Indicates good network link.
	DIAGNOSTICS			LED (Yellow) Blinking: Indicates transmitting data from iSE to flash memory
				card. When DHCP enabled, it remains solid until DHCP IP address is received.
	°C/°F			LED (Green) Blinking: Indicates receiving data by the iSE from flash memory.
	°C/°F			Button: Change display units of measurement from °C to °F
	TIME			Button: Change display from DATE and TIME to TEMP
	BKLT			Button: Display Back Light
	When using the			small push buttons, hold the button until “WAIT” is displayed on the LCD and
	When using the
	then release.	7
		7

Image 11

Contents User’s Guide Page Dhcp DNS ISE and iLD Big Display on the Ethernet Network List of FiguresFeatures Part Introduction Page ISE and iLD Big Display on the Ethernet Network Wall Mounting Part 2 HardwareDIP Switch Location DIP SwitchesParts of iSE Unit Parts of the iSE UnitOpening the Unit Disassembly InstructionNetwork Communication Interfaces 1 10Base-T RJ-45 Pinout Relay and I/O Contact Wiring ConnectionsCrossover Cable Wiring Battery and S5 Jumper Location Running on Battery PowerData Record Test Flash Memory FormatEthernet MAC Address Network Configuration 3.1 Network ProtocolsPart Section DhcpDNS Subnet MaskExample C\Telnet 192.168.1.200 Default IP AddressPort Number Part Operations Testing the ConnectionIConnect Software ISERVER Home Access Control Setting a New IP Address over the NetworkLogin and Administrator Passwords Setup and Operation Using the iSE WebPrompted for a password, as shown in Figure Read Sensor Read Sensor Java Runtime Environment 1.4 Setup instructionsDiagnostics Java Runtime Environment 1.5 5.0 Setup instructionsAccessing iSE units using the internet Fla sh Archive Adjustable ChartOption Retrieving Data from FlashDhcp can be enabled by setting the dip switch number #4 RTC is not set and the Flash Card is not empty Configuration#1 RTC is not set and Flash Card is empty #2 RTC is set, and recording is in progressMegaBytes Flash Card 22 Kbytes Used Space Flash Recording SettingsRemote Access Tunneling Real Time ClockTemperature 1 and Temperature Configuration/Device SetupFlash Recording Input 2 Status Unlatch, Latch, Clear Latch, Chart SPConfiguration Terminal Server Configuration Input Contact ClosureConfiguration Remote Access Sensor Parameters 12 Sensor Parameters TemperatureTA71.34FTA72.48FTD-1.19F TA71.34F TA72.48F TD-1.19FHTTPget Program Telnet SetupHTTPget using Port Srhf SrtcSrtf SrhcWhere HTTPget and ARP to setup Device IP AddressArp -s 192.168.1.200 00-03-34-00-06-b6 ARP Protocol 15 ARP Commands and Responses16 iLog Software Logging Data ILog SoftwareMail Notifier Software InstallationOptions Email Setup19 iSE Mail Notifier Device Setting Device Setting and Configuration Device setup requiresThermocouple Input Part Specifications Sensor SpecificationsPackaging PowerInterfaces EnvironmentalNetwork Interface Measurement Category Part Approvals Information CE ApprovalAppendix Aglossary Appendix BIP Address Mask Dotted Notation Mask Binary Mask Bits Appendix CIP NetmaskAddress Class Mask Binary Value Mask Decimal Value Or Dotted NotationChar No Parity No parity Appendix D Hex Ascii Chart Dec BinaryAscii Dec BinaryChar Equiv Appendix D Ascii Chart ContinuationDec Hex Ctrl Key Ascii Control Codes Definition Appendix E ILog Error Messages Error # Description Page Page WARRANTY/DISCLAIMER Shop on line at omega.com