Omega Speaker Systems iSE-TC manual Configuration Input Contact Closure, Terminal Server

Page 34

4.3.5 Configuration (continued)

G) Input Contact Closure

Contact 1: Disable, Normally Open, Normally Close

Contact 2: Disable, Normally Open, Normally Close

Disabled: Contact is dysfunctional.

Normally Open: Contact is open. If the contact is closed, there will be an Output High or Low,.depending on which output is selected. Read Sensor page will display: Normal

Normally Close: Contact is closed. If the contact is open, there will be an Output High or Low, depending on which output is selected. Read Sensor page will display: Active.

Active Contact Output: Active High, Active Low. The Output can be High or Low when the status on the input contact is changed.

Output Type: Unlatch, Latch, Clear Latch

H) Terminal Server

TCP/UDP*: The iSE supports TCP and UDP protocols (default is TCP). If UDP is selected, it can be configured either for Broadcast UDP or Directed UDP. In case of Broadcast UDP, the iSE will transmit the data to every node on the network. This can be accomplished if the Remote IP Address is set to 255.255.255.255.

The Broadcast UDP is a practical solution when one iSE needs to communicate with multiple nodes over the network. In the case of directed UDP, the iSE will transmit the data to a specific node on the network. This can be accomplished if the Remote IP Address is set to the IP address of that specific node.

Server Type: Continuous mode sends the temperature to the Ethernet, every two seconds. It is mainly used to send readings to a remote display.

Command mode (default) needs a command to query the iSE to send the reponse back to querying device.

Forward CR: Forward CR can be enabled and disabled. If enabled the iSE will forward a <CR> along with the data to a network host.

Number of Connections: The range is from 0 to 5. If 0 is selected, the Terminal Server feature is disabled. This means that no network connection can be made to the sensor connected to the iSE. If 1 is selected, only one network connection can be made to the iSE’s. Any number more than 1 would allow that number of network hosts to read from the iSE simultaneously (default is 5).

Port: Port 2000 is the default TCP port for the iSE’s port to which the sensors are connected. Ports 1000 (used for HTTPget, refer to Section 4.5), 2002, 2003, and 2004 are reserved for internal use.

Terminal Server usually describes a device that exchanges data between Ethernet/TCPIP networks and RS-232/RS-485 systems. With this iSE, the data is obtained digitally from the sensor (irrelevant to RS-232 or RS-485 interface) and can be accessed from anywhere on the network.

A computer program, such as Mail Notifier, OPC Server, iLog, iFlash or HTTPget can send TCP requests and obtain readings using the Terminal Server feature.

30

Page 33 Page 35
Image 34
Page 33 Page 35
Contents User’s Guide Page Dhcp DNS List of Figures ISE and iLD Big Display on the Ethernet NetworkFeatures Part Introduction Page ISE and iLD Big Display on the Ethernet Network Part 2 Hardware Wall MountingDIP Switches DIP Switch LocationParts of the iSE Unit Parts of iSE UnitDisassembly Instruction Opening the UnitCrossover Cable Wiring Relay and I/O Contact Wiring ConnectionsNetwork Communication Interfaces 1 10Base-T RJ-45 Pinout Running on Battery Power Battery and S5 Jumper LocationFlash Memory Format Data Record TestPart Network Configuration 3.1 Network ProtocolsEthernet MAC Address Subnet Mask DhcpDNS SectionPort Number Default IP AddressExample C\Telnet 192.168.1.200 Testing the Connection Part OperationsIConnect Software ISERVER Home Setting a New IP Address over the Network Access ControlPrompted for a password, as shown in Figure Setup and Operation Using the iSE WebLogin and Administrator Passwords Read Sensor Java Runtime Environment 1.4 Setup instructions Read SensorAccessing iSE units using the internet Java Runtime Environment 1.5 5.0 Setup instructionsDiagnostics Adjustable Chart Fla sh ArchiveRetrieving Data from Flash OptionDhcp can be enabled by setting the dip switch number #2 RTC is set, and recording is in progress Configuration#1 RTC is not set and Flash Card is empty #4 RTC is not set and the Flash Card is not emptyReal Time Clock Flash Recording SettingsRemote Access Tunneling MegaBytes Flash Card 22 Kbytes Used SpaceConfiguration/Device Setup Temperature 1 and TemperatureInput 2 Status Unlatch, Latch, Clear Latch, Chart SP Flash RecordingConfiguration Configuration Input Contact Closure Terminal ServerConfiguration Remote Access 12 Sensor Parameters Temperature Sensor ParametersTA71.34F TA72.48F TD-1.19F TA71.34FTA72.48FTD-1.19FTelnet Setup HTTPget ProgramHTTPget using Port Srhc SrtcSrtf SrhfArp -s 192.168.1.200 00-03-34-00-06-b6 HTTPget and ARP to setup Device IP AddressWhere 15 ARP Commands and Responses ARP ProtocolILog Software 16 iLog Software Logging DataInstallation Mail Notifier SoftwareEmail Setup OptionsDevice Setting and Configuration Device setup requires 19 iSE Mail Notifier Device SettingPart Specifications Sensor Specifications Thermocouple InputEnvironmental PowerInterfaces PackagingNetwork Interface Part Approvals Information CE Approval Measurement CategoryAppendix Aglossary Appendix BIP Address Or Dotted Notation Appendix CIP NetmaskAddress Class Mask Binary Value Mask Decimal Value Mask Dotted Notation Mask Binary Mask BitsDec Binary Appendix D Hex Ascii Chart Dec BinaryAscii Char No Parity No parityDec Hex Ctrl Key Ascii Control Codes Definition Appendix D Ascii Chart ContinuationChar Equiv Appendix E ILog Error Messages Error # Description Page Page WARRANTY/DISCLAIMER Shop on line at omega.com
Top Page Image Contents