Omega Speaker Systems iSE-TC manual Part Operations, Testing the Connection

Page 19

PART 4

OPERATIONS

This iSE can be used and configured in several ways, depending on user’s preference and network setup. It can be configured using a Web browser, like Netscape or Internet Explorer. It can also be configured using the iConnect Configuration Software.

If DHCP and DNS servers are used, the connection is very simple, no need to find the right IP address or watch for network conflicts, these are all done for you by your network DHCP and DNS server. All that is left for you to do, is to enable DHCP on the iSE (see Section 2.2) and use a straight network cable to connect the iSE to a hub and power it up.

If DHCP is not the preferred method, you can configure your PC’s network connection with an IP address of 192.168.1.x that is in the same range as the iSE’s default IP address (192.168.1.200) and connect to the iSE using a cross-over network cable between your PC’s network port and the iSE. After you’re done with configuring the iSE, you can always set your PC back to its original settings.

On your computer, from the MS-DOS Prompt window type "ping 192.168.1.200” and press Enter. If DHCP and DNS servers are used type “ping eisxxxx”, where xxxx are the last four digits of the iSE’s MAC address, located on the back of the device. You should get a reply as shown in Figure 4.1.

You can use the iSE host name (eisxxxx) instead of its IP address only if your DHCP server is configured to communicate with your DNS. Please consult with your IT department for details.

4.0 Testing the Connection

C:\>ping eis03ec

Pinging eis03ec with 32 bytes of data:

Reply from eis03ec: bytes=32 time=15ms TTL=60

Reply from eis03ec: bytes=32 time=8ms TTL=60

Reply from eis03ec: bytes=32 time=8ms TTL=60

Reply from eis03ec: bytes=32 time=8ms TTL=60

Pinging statistics for eis03ec:

Packets: Sent=4, Received=4, Lost=0 (0% loss)

Approximate round trip times in milli-seconds:

Minimum=8ms, Maximum=15ms, Average=9ms

Figure 4.1 Pinging the iSE from MS-DOS Prompt

This proves that the connection is proper and you can get into configuration or run mode using the Telnet or Web browser.

15

Image 19

Contents User’s Guide Page Dhcp DNS ISE and iLD Big Display on the Ethernet Network List of FiguresFeatures Part Introduction Page ISE and iLD Big Display on the Ethernet Network Wall Mounting Part 2 HardwareDIP Switch Location DIP SwitchesParts of iSE Unit Parts of the iSE UnitOpening the Unit Disassembly InstructionCrossover Cable Wiring Relay and I/O Contact Wiring ConnectionsNetwork Communication Interfaces 1 10Base-T RJ-45 Pinout Battery and S5 Jumper Location Running on Battery PowerData Record Test Flash Memory FormatPart Network Configuration 3.1 Network ProtocolsEthernet MAC Address Section DhcpDNS Subnet MaskPort Number Default IP AddressExample C\Telnet 192.168.1.200 Part Operations Testing the ConnectionIConnect Software ISERVER Home Access Control Setting a New IP Address over the NetworkPrompted for a password, as shown in Figure Setup and Operation Using the iSE WebLogin and Administrator Passwords Read Sensor Read Sensor Java Runtime Environment 1.4 Setup instructionsAccessing iSE units using the internet Java Runtime Environment 1.5 5.0 Setup instructionsDiagnostics Fla sh Archive Adjustable ChartOption Retrieving Data from FlashDhcp can be enabled by setting the dip switch number #4 RTC is not set and the Flash Card is not empty Configuration#1 RTC is not set and Flash Card is empty #2 RTC is set, and recording is in progressMegaBytes Flash Card 22 Kbytes Used Space Flash Recording SettingsRemote Access Tunneling Real Time ClockTemperature 1 and Temperature Configuration/Device SetupFlash Recording Input 2 Status Unlatch, Latch, Clear Latch, Chart SPConfiguration Terminal Server Configuration Input Contact ClosureConfiguration Remote Access Sensor Parameters 12 Sensor Parameters TemperatureTA71.34FTA72.48FTD-1.19F TA71.34F TA72.48F TD-1.19FHTTPget Program Telnet SetupHTTPget using Port Srhf SrtcSrtf SrhcArp -s 192.168.1.200 00-03-34-00-06-b6 HTTPget and ARP to setup Device IP AddressWhere ARP Protocol 15 ARP Commands and Responses16 iLog Software Logging Data ILog SoftwareMail Notifier Software InstallationOptions Email Setup19 iSE Mail Notifier Device Setting Device Setting and Configuration Device setup requiresThermocouple Input Part Specifications Sensor SpecificationsPackaging PowerInterfaces EnvironmentalNetwork Interface Measurement Category Part Approvals Information CE ApprovalAppendix Aglossary Appendix BIP Address Mask Dotted Notation Mask Binary Mask Bits Appendix CIP NetmaskAddress Class Mask Binary Value Mask Decimal Value Or Dotted NotationChar No Parity No parity Appendix D Hex Ascii Chart Dec BinaryAscii Dec BinaryDec Hex Ctrl Key Ascii Control Codes Definition Appendix D Ascii Chart ContinuationChar Equiv Appendix E ILog Error Messages Error # Description Page Page WARRANTY/DISCLAIMER Shop on line at omega.com