High End Systems SHOWGUN user manual Chapter Setup and Configuration, Unpacking the Fixture

Page 19

Chapter 2:

Setup and Configuration

SHOWGUN® fixture setup includes mounting, connecting to power and DMX linking and configuration.

Use the following steps to set up and configure your SHOWGUN® fixture:

1.Unpack the fixture.

2.Install power cord cap for your location.

3.Mount the fixture upright or suspended from a standard truss.

4.Connect the fixture to a DMX controller via DMX cabling.

5.Connect the fixture to power.

6.Configure the fixture for DMX control.

Unpacking the Fixture

The SHOWGUN® fixture ships in a road case specifically designed to protect the product during transport. When unpacking, inspect the fixture for physical damage to components. High End Systems® assumes no responsibility for products that are damaged during transport. Return a product for repair in its road case.

Before sending anything to the factory, call your High End Systems dealer/distributor for a Return Material Authorization (RMA) number. The factory cannot accept any goods shipped without an RMA number.

Installing a Power Cord Cap

The SHOWGUN® fixture’s custom power cord ships without a power cord cap. Use the information in this section to install the correct power cord cap for your location.

Because of the variety of power cord caps used worldwide, High End Systems, Inc. cannot make specific recommendations for the power cord cap. Contact a local authority for the type of power cord cap needed. When installing the power cord cap, note that the cores in the mains lead are colored according to the following code:

green and yellow = earth

blue = neutral

brown = live

SHOWGUN® User Manual

7

Image 19
Contents High End Systems, Inc , All Rights Reserved Americas Contacting High End SystemsAccording to ISO/IEC Guide 22 and EN45104 Declaration of ConformityProduct Modification Warning Important Safety InformationInjury and/or damage to equipment FCC Information Safety SymbolsFreight Warranty InformationLimited Warranty Returning an Item Under Warranty for RepairVii Viii Table of Contents Showgun Menu System Fixture Programming Maintenance and Troubleshooting Chapter Product Overview Showgun FeaturesFixture Construction OperationPart Description Part Number Related Products and AccessoriesMechanical SpecificationsElectrical PowerOperational EnvironmentalCable and Connector Specifications Lamp SpecificationsLithoPattern Specifications Installing a Power Cord Cap Chapter Setup and ConfigurationUnpacking the Fixture Mounting the Fixture Installing a Line Cord Cap U.K. OnlyVatic Fitter Heads Information Danmark Truss Mounting Mounting the Fixture UprightLinking Showgun Fixtures Cable ConnectorsConnecting to the Link Powering On the FixtureFixture Homing Shutting Down the Fixture Setting the DMX Start ChannelNavigating the Menu System Chapter Showgun Menu SystemShowgun Display Fixture Software Version DMX Start Channel Display in Menu Locked ModeError Message Display Navigational BasicsExiting the Menu System Unlocking the Menu SystemMenu Map Level Option/Setting Description/NotesFollowing sensors LevelDetermining DMX Start Channel Assignment Setting DMX Start ChannelMenu System Options DMX Address MenuChannel Location Fixture Channels Start FixtureType Used per Channel Link Fixture Set Parameters Menu Factory Default SettingsPan/Tilt Swap Tilt Invert Pan InvertLamp Life Limit Data Loss TimeoutHoming the Fixture Fixture Mode MenuTest Options Menu Crossloading Fixture SoftwareLamp State Copying the Boot CodeDisplay Test Motor Setup Encoder Disable Code MenuDMX Values Menu Information MenuSensor Status Menu Unique NumberFixture Hours Temperatures MenuLamp Strikes Fixture Hours ResetLamp HR/Strike Reset Lamp HoursModule Version Display ErrorsNext DMX Channel DMX Programming Options Chapter Fixture ProgrammingDMX Programming Overview Full Speed verses MSpeed ControlPan and Tilt Showgun DMX ParametersChannel Function Color Function Description Color MixingCMY Color Tri ColorLED Tracking System Dimming LED Tracking SystemRGB Color LED Tracking FunctionsShutter/Lamp Function Shutter Channel Shutter and Lamp EffectsMSpeed Motor Speed Zoom and FocusMacros Control Setting Description Control SettingsChapter Replacing Fuses Chapter Maintenance and TroubleshootingFixture Component Replacement Fuse Fuse Location and Access Symptom of FailureReplacing the Lamp Replacement FusesFuse Fuse Type and Rating Manufacturer HES Part Number Chapter Driver Boards Phase BoardsPan Board Phase BoardReplacing Lithopatterns Microfresnel Lens Cleaning the Showgun FixtureAchromatic Lens Filter ReflectorSoft Edge Flag Bulk Head Accessing the Bulk HeadsProduction Homing Iris and Gobo Bulk HeadFlag Calibration Example Connect dimmer flag motors directly to 2-phase driverCalibrate the flags AdjustmentChapter Power Supply TroubleshootingPower Board Connection Functions Supply Powered Board LED States State Problem? DescriptionAppendix a MSpeed Conversion Table Dec Appendix B Important Safety Information Appendix B Important Safety Information Appendice C Importantes Informations Sur La Sécurité Warnung Zum Schutz Vor Verletzungen Anhang C Wichtige Hinweise Für Ihre SicherheitWarnung Zum Schutz Vor Brandgefahr Warnung Zum Schutz Gegen Gefährliche KörperströmeAdvertencia Para Protección Continua Contra Incendios Apéndice C Información Importante De SeguridadAvvertenza Per Non Ferire Ad Altre Persone Appendice C Importanti Informazioni Di SicurezzaAvvertenza Per Prevenire Incendi Avvertenza Per Prevenire Le Scosse ElettricheVigtig Sikkerhedsinformation Appendix B Important Safety Information