High End Systems SHOWGUN user manual Control Settings, Control Setting Description

Page 47

CHAPTER 4

Fixture Programming

Control Settings

The Control parameter activates certain Fixture functions. To access all SHOWGUN® Control settings (except for Pan & Tilt MSpeed Off), first select a control channel value, then set the Shutter channel to “0.”

NOTE: The Control channel should not be crossfaded.

Control Setting

Description

 

 

Safe

Disables all Control settings for normal operation.

 

 

Pan & Tilt MSpeed Off

Sets Pan & Tilt MSpeed to ignore MSpeed settings.

 

 

Display Off

Sets display to off.

 

 

Display Bright

Brightens the display characters.

 

 

Home

Remotely homes the fixture.

 

 

Lamp On

Remotely restrikes the fixture’s lamp.

 

 

Lamp Off

Remotely extinguishes the fixture’s lamp.

 

 

Shutdown

Remotely deactivates the fixture. When a fixture is shut

 

down, the lamp is extinguished, power to the motors is

 

disabled, and the LED display reads “SHUT DOWN”. If a fixture is

 

in shutdown mode, you must home the fixture to bring it back

 

into operation.

 

 

SHOWGUN® User Manual

35

Image 47
Contents High End Systems, Inc , All Rights Reserved Americas Contacting High End SystemsAccording to ISO/IEC Guide 22 and EN45104 Declaration of ConformityProduct Modification Warning Important Safety InformationInjury and/or damage to equipment FCC Information Safety SymbolsFreight Warranty InformationLimited Warranty Returning an Item Under Warranty for RepairVii Viii Table of Contents Showgun Menu System Fixture Programming Maintenance and Troubleshooting Fixture Showgun FeaturesChapter Product Overview Construction OperationPart Description Part Number Related Products and AccessoriesMechanical SpecificationsElectrical PowerOperational EnvironmentalLithoPattern Specifications Lamp SpecificationsCable and Connector Specifications Unpacking the Fixture Chapter Setup and ConfigurationInstalling a Power Cord Cap Vatic Fitter Heads Information Danmark Installing a Line Cord Cap U.K. OnlyMounting the Fixture Truss Mounting Mounting the Fixture UprightLinking Showgun Fixtures Cable ConnectorsFixture Homing Powering On the FixtureConnecting to the Link Shutting Down the Fixture Setting the DMX Start ChannelShowgun Display Chapter Showgun Menu SystemNavigating the Menu System Fixture Software Version DMX Start Channel Display in Menu Locked ModeError Message Display Navigational BasicsExiting the Menu System Unlocking the Menu SystemMenu Map Level Option/Setting Description/NotesFollowing sensors LevelDetermining DMX Start Channel Assignment Setting DMX Start ChannelMenu System Options DMX Address MenuType Used per Channel Link Fixture FixtureChannel Location Fixture Channels Start Pan/Tilt Swap Factory Default SettingsSet Parameters Menu Tilt Invert Pan InvertLamp Life Limit Data Loss TimeoutHoming the Fixture Fixture Mode MenuTest Options Menu Crossloading Fixture SoftwareLamp State Copying the Boot CodeDisplay Test Motor Setup Encoder Disable Code MenuDMX Values Menu Information MenuSensor Status Menu Unique NumberFixture Hours Temperatures MenuLamp Strikes Fixture Hours ResetLamp HR/Strike Reset Lamp HoursNext DMX Channel Display ErrorsModule Version DMX Programming Options Chapter Fixture ProgrammingDMX Programming Overview Full Speed verses MSpeed ControlChannel Function Showgun DMX ParametersPan and Tilt Color Function Description Color MixingCMY Color Tri ColorLED Tracking System Dimming LED Tracking SystemRGB Color LED Tracking FunctionsShutter/Lamp Function Shutter Channel Shutter and Lamp EffectsMacros Zoom and FocusMSpeed Motor Speed Control Setting Description Control SettingsChapter Replacing Fuses Chapter Maintenance and TroubleshootingFixture Component Replacement Fuse Fuse Location and Access Symptom of FailureFuse Fuse Type and Rating Manufacturer HES Part Number Replacement FusesReplacing the Lamp Chapter Driver Boards Phase BoardsPan Board Phase BoardReplacing Lithopatterns Achromatic Lens Cleaning the Showgun FixtureMicrofresnel Lens Filter ReflectorSoft Edge Flag Bulk Head Accessing the Bulk HeadsProduction Homing Iris and Gobo Bulk HeadFlag Calibration Example Connect dimmer flag motors directly to 2-phase driverCalibrate the flags AdjustmentChapter Power Board Connection Functions Supply Powered TroubleshootingPower Supply Board LED States State Problem? DescriptionAppendix a MSpeed Conversion Table Dec Appendix B Important Safety Information Appendix B Important Safety Information Appendice C Importantes Informations Sur La Sécurité Warnung Zum Schutz Vor Verletzungen Anhang C Wichtige Hinweise Für Ihre SicherheitWarnung Zum Schutz Vor Brandgefahr Warnung Zum Schutz Gegen Gefährliche KörperströmeAdvertencia Para Protección Continua Contra Incendios Apéndice C Información Importante De SeguridadAvvertenza Per Non Ferire Ad Altre Persone Appendice C Importanti Informazioni Di SicurezzaAvvertenza Per Prevenire Incendi Avvertenza Per Prevenire Le Scosse ElettricheVigtig Sikkerhedsinformation Appendix B Important Safety Information