High End Systems SHOWGUN user manual Chapter

Page 60

CHAPTER 5

Maintenance and Troubleshooting

11.To adjust a flag horizontally, position the flag loosely against the outside standoff and tighten the set screw. Lightly tap on the flag making it hit the inside standoff.

The flag should be close enough to the standoff so when you tap on it you should hear a clicking sound. If not, try to calibrate again by moving the flag while it is still tightened to the motor. Loosen the set screw, position the flag almost against the standoff, tighten the set screw, test with tapping the flag.

Moving the flag while the screw is still tight and then loosening the set screw will position the flag at another point on the motor.

12.Remove the service harness and reattach the connectors to the 2-phase driver board.

13.Reinsert the bulk head and replace the two 4M socket caps.

14.Home the fixture and test flags. Make sure they are not hitting when fully closing from the console or the menu system.

48

SHOWGUN® User Manual

Image 60
Contents High End Systems, Inc , All Rights Reserved Contacting High End Systems AmericasDeclaration of Conformity According to ISO/IEC Guide 22 and EN45104Important Safety Information Product Modification WarningFCC Information Safety Symbols Injury and/or damage to equipmentWarranty Information Limited WarrantyReturning an Item Under Warranty for Repair FreightVii Viii Table of Contents Showgun Menu System Fixture Programming Maintenance and Troubleshooting Showgun Features Chapter Product OverviewFixture Operation ConstructionRelated Products and Accessories Part Description Part NumberSpecifications MechanicalPower OperationalEnvironmental ElectricalLamp Specifications Cable and Connector SpecificationsLithoPattern Specifications Chapter Setup and Configuration Installing a Power Cord CapUnpacking the Fixture Installing a Line Cord Cap U.K. Only Mounting the FixtureVatic Fitter Heads Information Danmark Mounting the Fixture Upright Truss MountingCable Connectors Linking Showgun FixturesPowering On the Fixture Connecting to the LinkFixture Homing Setting the DMX Start Channel Shutting Down the FixtureChapter Showgun Menu System Navigating the Menu SystemShowgun Display Display in Menu Locked Mode Error Message DisplayNavigational Basics Fixture Software Version DMX Start ChannelUnlocking the Menu System Exiting the Menu SystemLevel Option/Setting Description/Notes Menu MapLevel Following sensorsSetting DMX Start Channel Menu System OptionsDMX Address Menu Determining DMX Start Channel AssignmentFixture Channel Location Fixture Channels StartType Used per Channel Link Fixture Factory Default Settings Set Parameters MenuPan/Tilt Swap Pan Invert Tilt InvertData Loss Timeout Lamp Life LimitFixture Mode Menu Test Options MenuCrossloading Fixture Software Homing the FixtureCopying the Boot Code Display Test Motor SetupEncoder Disable Code Menu Lamp StateInformation Menu Sensor Status MenuUnique Number DMX Values MenuTemperatures Menu Fixture HoursFixture Hours Reset Lamp HR/Strike ResetLamp Hours Lamp StrikesDisplay Errors Module VersionNext DMX Channel Chapter Fixture Programming DMX Programming OverviewFull Speed verses MSpeed Control DMX Programming OptionsShowgun DMX Parameters Pan and TiltChannel Function Color Mixing CMY ColorTri Color Color Function DescriptionLED Tracking System RGB ColorLED Tracking Functions LED Tracking System DimmingShutter and Lamp Effects Shutter/Lamp Function Shutter ChannelZoom and Focus MSpeed Motor SpeedMacros Control Settings Control Setting DescriptionChapter Chapter Maintenance and Troubleshooting Fixture Component ReplacementFuse Fuse Location and Access Symptom of Failure Replacing FusesReplacement Fuses Replacing the LampFuse Fuse Type and Rating Manufacturer HES Part Number Chapter Phase Boards Driver BoardsPhase Board Pan BoardReplacing Lithopatterns Cleaning the Showgun Fixture Microfresnel LensAchromatic Lens Reflector FilterAccessing the Bulk Heads Production HomingIris and Gobo Bulk Head Soft Edge Flag Bulk HeadConnect dimmer flag motors directly to 2-phase driver Flag Calibration ExampleAdjustment Calibrate the flagsChapter Troubleshooting Power SupplyPower Board Connection Functions Supply Powered State Problem? Description Board LED StatesAppendix a MSpeed Conversion Table Dec Appendix B Important Safety Information Appendix B Important Safety Information Appendice C Importantes Informations Sur La Sécurité Anhang C Wichtige Hinweise Für Ihre Sicherheit Warnung Zum Schutz Vor BrandgefahrWarnung Zum Schutz Gegen Gefährliche Körperströme Warnung Zum Schutz Vor VerletzungenApéndice C Información Importante De Seguridad Advertencia Para Protección Continua Contra IncendiosAppendice C Importanti Informazioni Di Sicurezza Avvertenza Per Prevenire IncendiAvvertenza Per Prevenire Le Scosse Elettriche Avvertenza Per Non Ferire Ad Altre PersoneVigtig Sikkerhedsinformation Appendix B Important Safety Information